Denver TFD-1906DVBT User Manual

TFD-1906DVBT AC/DC
19 TFT LCD TV+DVD COMBO/DVBT" Operating Instructions
PAL/SECAM B/G,D/K, I
AC 110-240V 50/60Hz SCART IN, PC IN TELETEXT NTSC PLAYBACK INSIDE DVD SUPPORT FORMAT: SVCD, VCD, WMA, HDCD, KODAK PICTURE CD, DVD MPEG4
TABLE OF CONTENTS
Table of Contents
Specifications
Installation
Important Safety Instruction
Warnings and Cautions
Setup
Functional Parts(TV)
Functional Parts(DVD)
Rear view of TV set
Remote Control unit
TELETEXT Operations
Remote Control Operation(DVD)
Remote Control Unit
MENU Screens
5-7
9
10
11
12-13
14
15-16
17
18-19
1
Inital Settings(DVD)
DVBT Setup Menu Setting
2
Troubleshooting Tips
3
The Causes of interference
4
8
20-21
22-25
26
27
1
SPECIFICATIONS
Receiving System:
Colour System:
LCD Panel:
Ext.Antenna:
Ext. In/Out:
Speaker:
Audio Output:
Power Consumption:
Dimension:
B/G, D/K, I
PAL, SECAM
482.6mm(19 inch) diagonal
75 Ohm Coaxial Cable
PC Input, SCART IN
16 Ohm x 2
3W
AC 110-240V 50/60Hz,60W / 12V
W466 xD206 xH415.7(mm)
Net Weight:
7.0KG
Note:Design and specifications are subject to change without prior notice.
OPEN/CLOSE POWER
Q.
Q.
-/---/--
VIEW
VIEW
FORMAT
SUB.T
INFO
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
MENU
VOL-
SYS.
PROG-
STOP
REVEAL SIZE
PAGE PAGE
TEXT
INDEX
ANGLE SLOW
TITLE
DVD MENU PROGRAM SUBTITLE
EPG
ENTER
DVD SETUP
GOTO
RADIO
LANG
P.PP.P
SWAPSWAP
RECALL
TEXT
VOL+
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
REMOTE CONTROL
Transmitting System :Infrared
Power Supply :DC 3V
2
INSTALLATION
Thank you very much for your purchase of this product, the most natural Colour Television Receiver. To enjoy your set to the full from the very beginning, read this manual carefully and keep it handy for ready reference.
INSTALLATION
Locate the receiver in the room where direct light does not strike the screen.
Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing.
Allow enough space between the receiver and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure.
This TV operates on a DC supply provided by the AC-DC adaptor. The voltage is as Indicated on the label on the back cover.Only use the AC-DC adaptor supplied with the TV and never apply an AC mains to the TV directly. The AC-DC adaptor operates on and AC mains supply, the voltage is as indicated on the label of the AC-DC adaptor. Connect the DC plug of the AC-DC adaptor to the DC 12V socket at the back of the TV. Connect the AC-DC adaptor and its mains cord. Insert the mains plug in the wall socket having a mains voltage of 110-240V. Do not install the receiver in a location near heat sources such as radiator, air ducts, direct sunlight ,or in a place somewhere like close compartment and close area.
Do not cover the ventilation openings when using the set.
CAUTION
Never tamper with any components inside your set, or any other adjustment controls not mentioned in this manual. The LCD panel used in this product is made of glass. Therefore,it can break When the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.When you clean up dust or stick of a water drop on the LCD panel. The power cord should be pulled out from the plug receptacle, then wipe the receiver with dried soft cloth .During thunder and lighting , unplug the power cord and antenna cord to prevent your TV set from damage. All television receivers are high voltage instruments. All "inside work" on your receiver should be performed only by the TV service personnel.
If some abnormal phenomena happens , may be you have some mis-opertion,please take off power and restart your TV set .
3
IMPORTANT SAFETY INSTRUCTION
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lighting flash with arrow head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
4
WARNINGS AND CAUTIONS
Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver.
Do not insert anything in the ventilation holes. If metal or something flammable enters, it may result in fire or electric shock.
Caution
Caution
Caution
Do not place objects on this unit, it may damage the screen surface.
Caution
Do not squash power supply cord under the television receiver.
Caution
Do not throw anything at the set. The screen glass may explode by impact and cause serious injury.
5
WARNINGS AND CAUTIONS
Never stand on, lean on, or suddenly push the television or its stand. You should pay special attention to children. Serious injury may result if it should fall.
Do not place your television on an unstable cart , stand , shelf or table. Serious injury to an individual, and damage to the television, may result if it should fall.
Caution
Caution
Caution
6
When the television receiver is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet .
Caution
Do not block the ventilation holes in the back cover. Adequate ventilation is essential to prevent failure of electrical component.
Warning
Avoid exposing the television receiver to direct sunlight and other source of the heat. Do not stand the television receiver directly on other produces which give off heat .E.g.video cassette players. Audio amplifiers. Do not place naked flame sources, such as lighted candle on the television. Do not expose the LCD screen surface to the sun, it may damage the screen surface.
WARNINGS AND CAUTIONS
Take care not to connect many appliances to the same mains socket as this could result in fire or electric shock.
High voltages are used in the operation of this television receiver. Do not remove the cabinet back from your set. Refer servicing to qualified service personnel.
Warning
Warning
Warning
To prevent fire or electrical shock hazard, Do not expose the television receiver to rain or moisture.
Warning
For you own safety, Do not touch any part of the set, main lead or aerial lead during lighting storms.
Caution
If the television is to be built into a Compartment or similarly enclosed, the minimum distances must be maintained. Heat build-up can reduce the service life of your television, and can also be dangerous.
7
¼ò ½é¼ò ½é
SETUP
Remote Control Battery Installation
Requires two AAA batteries(supplied).
Procedure
1. Turn the remote control face down. Remove battery cover by pressing down on the marking on the cover and sliding it off in the direction indicated.
2. Install batteries matching(+) and(-) polarity signs.
3. Replace the battery cover by sliding in reverse until the lock snaps. Note: Incorrect installation can cause battery leakage and corrosion that will damage the Remote control. Precautions Replace batteries in pair. Do not mix battery types(zinc carbon with alkaline). Do not recharge, heat, short-circuit, disassemble, or burn batteries.
4.If you cause a static discharge when touching the unit, and the unit fails to function, simply unplug the unit from the AC outlet, wait a few minutes, and plug it back in. The unit should return to normal operation.
8
FUNCTIONAL PARTS(TV)
Front View of LCD Set
9 8 7 6 5 4
TV/DVD
V- V+
P-
MENU
P+
3
STANDBY
1. LED indicator lamp
2. Remote Sensor
3. Standby Button
4. ButtonTV/DVD
5. MENU Button
6. P+ Button
7. P- Button
8. V+Button
9. V- Button
2
1
To turn the TV power ON Put the TV set on the correct place, then connect the DC plug of the AC-DC adaptor to the DC 12V socket at the back of the TV set. Connect the adaptor main cord to the wall outlet ,then the LED indicator lamp turns red/green and the TV set is at Standby/work Mode. At Standby Mode, if Standby Button is pressed the power indicator will change to green. It takes a few seconds before the picture appears.
To turn the TV power OFF Press the Standby Button to make the TV set in Standby Mode, then disconnect the power plug from the wall outlet.
NOTE If TV is the selected input without signal received and NO operation is performed for about 5 minutes continuously, the TV set will enter standby mode. For any inputs other than TV, the TV set will not enter standby mode automatically without users instruction. If you are not going to use this TV set for a long time, switch off the set and disconnect the power plug from the wall outlet.
9
FUNCTIONAL PARTS(DVD)
3 4
6
2
1
1. DVD Slot
2. Open/Close
3. Stop
4. Play/Pause
5. Preview
6. Next
7. Repeat
Switch this LCD-TV Set to DVD status, insert the disk to DVD slot, and the player will suck it in.
Notes:
1.Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.
2.Do not use irregularly shaped CDs (e.g., Heartshaped or octagonal)since they may result in malfunctions.
3.Some playback operations of DVDs and Video CDs may be intentionally programmed by software manufacturers. This unit plays DVDS and Video CDs according to disc content designed by the software manufacturer, therefore some playback features may not be available or other functions may be added.
10
REAR VIEW OF TV SET
DC IN 12V HEADPHONE PC IN FULL-SCART
RF INPUT(ANT.)
TO DC IN 12V
TO POWER SOURCE
DC IN 12V
VGA
PC IN
AUDIO
Full-SCART
ANT .
NOTE
Precautions when connecting to other equipment
When using external equipment with this TV set, please read the instruction manual of the external equipment.
Switch off all power supplies to the equipment and TV set before connection.
Always ensure that the input and output terminals are correctly connected.
11
REMOTE CONTROL UNIT
POWER ON/STANDBY button
OPEN/CLOSE POWER
P.PP.P
Q.
Q.
-/---/--
FORMAT
SUB.T
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
VOL-
MENU
VIEW
VIEW
INFO
SWAPSWAP
RECALL
TEXT
VOL+
Press this button to switch on the TV when at standby mode or enter standby mode.
MUTE button
Press this button to mute or restore sound.
P.P Button
Press this button to select the desired picture mode: NORMAL/SOFT/RICH/CUSTOM.
DISPLAY Button
Press this button to display the setting on the screen.
SLEEP Button Press this button to set the sleep timer, the order shown below(minutes):
0 - 15 - 30 - 45 - 6 0
When the preset length of time has passed, the TV set enters standby mode.
AV/TV/DVD Button
Press ¡°AV/TV/DVD¡± button,the will be some word show on the right top of the screen, press ¡°PROG+/-¡± to select the AV source, and then press ¡°VOL+/-¡±to enter AV mode.
P.PP.P
SYS.
REVEAL SIZE
PAGE PAGE
INDEX
ANGLE SLOW
DVD MENU PROGRAM SUBTITLE
DVD SETUP
RADIO
PROG-
TEXT
ENTER
12
STOP
TITLE
EPG
GOTO
LANG
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
TV PC SCART DVD DVB-T
DIGIT Button(0-9)
This TV allows you to select channels from 0 to 255. Press this button to select one-digit,two digit or three -digital channels input options. To select a one-digit channel(e.g. Channel 8),press this ¡°-/--¡±button to change channel selection to ¡°-¡±on screen display and press the ¡°8¡±button only. To select a two-digit channel(e.g. Channel 28),press this ¡°-/--¡±button to change channel selection to ¡°--¡±on screen display and press¡°2¡± and ¡°8 ¡± buttons. To select a three-digit channel(e.g. Channel 128), press this¡°-/--¡±button to change channel selection to ¡°---¡±on screen display and press¡°1¡±,¡°2¡±and ¡°8¡± buttons.
REMOTE CONTROL UNIT
MENU Button
OPEN/CLOSE POWER
P.PP.P
Q.
Q.
-/---/--
VIEW
VIEW
SWAPSWAP
Press this button to enter the menu screens for various optional adjustable settings.
PROG+/- Button
Press the program up button to select the program forwards. Press the program Down button to select the program Backwards.
VOL+/- Button
Press volume up/down buttons to adjust sound level.
Q.VIEW Button
Press this button to return to the previously viewed program.
FORMAT
SUB.T
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
VOL-
SYS.
REVEAL SIZE
PAGE PAGE
INDEX
ANGLE SLOW
DVD MENU PROGRAM SUBTITLE
DVD SETUP
RADIO
MENU
PROG-
TEXT
ENTER
INFO
STOP
TITLE
EPG
GOTO
LANG
RECALL
TEXT
VOL+
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
SWAP Button
You can adjust your TV program list order, press this button, the program swap menu will displayed, as shown below. E.g. to swap channel 0 and 7 , press ¡°SWAP¡± button, press¡°PROG+/-¡± to choose .FROM and press ¡°VOL+/-¡± to set the channel number as ¡°0¡±,and as the same way to set the TO as¡°7¡±,last to do choose the¡°SAVE¡± and press ¡°VOL+/-¡± to implement this fuction.
FROM CH 0
TO CH 7
SAVE
13
TELETEXT OPERATIONS
For models with Teletext function only.
OPEN/CLOSE POWER
P.PP.P
Q.
Q.
-/---/--
FORMAT
SUB.T
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
VOL-
SYS.
REVEAL SIZE
PAGE PAGE
INDEX
ANGLE SLOW
DVD MENU PROGRAM SUBTITLE
DVD SETUP
RADIO
MENU
PROG-
TEXT
ENTER
VIEW
VIEW
INFO
STOP
TITLE
EPG
GOTO
LANG
SWAPSWAP
RECALL
TEXT
VOL+
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
TEXT Button
Press this button to enter or exit the teletext mode.
INDEX Button
Press the button to go to the index page.
REVEAL Button
Press this button to reveal the hidden information for some Teletext pages(e.g. answers to puzzles or riddles). Press again to hide the information.
MIX Button
Press this button enter to mix mode.(For SUBTITLE or NEWSFLASH page, please use mix mode). Press this button again to exit.
SIZE Button
Press this button to change the Teletext screen display mode among the following:
- Upper half screen enlarged
- Lower half screen enlarged
- Normal screen state
STOP Button Press this button to hold the Teletext page on display to prevent the page from changing. Press again to release the hold state.
SUB.PAGE
Press this button to display subpage.
COLOUR Button (optional)
Press this button to access directly to the corresponding pages displayed at the lower part of the Teletext screen.
14
REMOTE CONTROL OPERATION(DVD)
DVD Mode:
OPEN/CLOSE POWER
POWER
Press this button to switch television on or off.
P.PP.P
Q.
Q.
-/---/--
FORMAT
SUB.T
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
VOL-
SYS.
REVEAL SIZE
PAGE PAGE
INDEX
ANGLE SLOW
DVD MENU PROGRAM SUBTITLE
DVD SETUP
RADIO
MENU
PROG-
TEXT
ENTER
VIEW
VIEW
INFO
STOP
TITLE
EPG
GOTO
LANG
SWAPSWAP
RECALL
TEXT
VOL+
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
OPEN/CLOSE Button
Press OPEN/CLOSE button to load disc on disc tray. Hold the disc without touching either of its surfaces, position it with the printed title side facing up, align it with the guides, and place it in its proper position. In case of interactive DVDs with playback control, a menu appears on the TV screen.
DVD MENU Button
If play some DVD discs, press this button back to root menu screen.
PROGRAM Button
Place a track on the program list.
Press PROGRAM button, then the ¡°PROGRAM¡± will appear on TV screen now you can press¡°> ¡÷¨Œ¡±
> ¡÷¨Œ
and¡°ENTER¡±button to select ¡°START¡± option and enjoy the desired tracks.
SUBTITLE Button
To press this button, you can change the subtitle language from one selected to the initial settings to a different language, if available.
DVD SETUP Button
You can enjoy picture frame forward by pressing this button.
AUDIO Button
To press this button, you can change the audio language from the one selected at settings to a different language, if available.
GOTO Button
Press this button to go to desired position. The player provides 3 search mode When the above items are showed on TV screen, you can input number to locate desire sector, then press PLAY to commence play The number you input is invalid if it is beyond the track's capcity.
DISPLAY Button
To display player OSD.
PREV/NEXT Button
Press these button to go to the previous/next chapter(DVD).
FR/FF Button
These buttons allow skipping ahead/back at 5-level speed. Press ¡°PLAY¡±button to return to normal playback.
15
REMOTE CONTROL OPERATION(DVD)
OPEN/CLOSE POWER
P.PP.P
Q.
Q.
-/---/--
FORMAT
SUB.T
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
VOL-
SYS.
REVEAL SIZE
PAGE PAGE
INDEX
ANGLE SLOW
DVD MENU PROGRAM SUBTITLE
DVD SETUP
RADIO
MENU
PROG-
TEXT
ENTER
VIEW
VIEW
INFO
STOP
TITLE
EPG
GOTO
LANG
SWAPSWAP
RECALL
TEXT
VOL+
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
DVD Mode:
REPEAT Button
To press this button you can repeatedly play a title(DVD) or all tracks(CD) when¡°ALL ¡±appears on TV screen, you can repeatedly play a chapter (DVD) or a single track(CD) when¡°Repeat chapter¡±appears on TV screen, you can cancel repeat functions when no¡°Repeat off¡±appears on TV screen.
PLAY/PAUSE Button
Press this button to start playback. Press this button again to pause playback.
STOP Button
When this button is pressed once, the unit records the stopped point, from where playback will resume (resume function) if ¡°PLAY¡±is pressed after wards. But if STOP button is pressed again instead of PLAY button, there will be no resume function.
TITLE button
DVD disc: Press TITLE button, then the DVD menu or titles available on the disc will be displayed. Then you can use " " and ENTER button to select programs.
ZOOM button
1.Press ZOOM during playback or still playback to activate the Zoom function. The square frame appears briefly in the right bottom of the picture.
2. Each press of the ZOOM button changes the TV screen in the following sequence:
3. Use the buttons to move through the zoomed picture.
4. To resume normal playback, press ZOOM button until screen becomes 1X.
Note:Zoom may not work on some DVDs.
N
ANGLE button
If the disc contains scenes recorded at different camera angles, you can change to a different camera angle during playback. Press ANGLE repeatedly during playback to select a desired angle. Note that the number of the current angle appears on screen.
Note:
N
The angle indicator will blink on the TV screen during scenes recorded at different angles as an indication that angle switching is possible.
16
SLOW Button
Press this button during playback to activate the slow function. Each press on this button change the TV screen in the follow sequence:1/2 - 1/4 - 1/8 - 1/16 normal play
REMOTE CONTROL UNIT (DVB-T)
OPEN/CLOSE POWER
P.PP.P
Q.
Q.
-/---/--
FORMAT
SUB.T
REPEAT
DVB-T MENU
EXIT
MUTE TV/AV/DVD
PROG+
VOL-
SYS.
MENU
PROG-
VIEW
VIEW
INFO
SWAPSWAP
RECALL
TEXT
VOL+
DVB-T Mode:
FORMAT: used to change the TV picture aspect
SUB.T(SUBTITLE): used to switch subtitles on or off
INFO: used to display information for the channel being viewed
RECALL: reverts to previous channel
EXIT: used to return to TV
DVBT-MENU: used to open and close the menu windows
TEXT: used to open the interactive digital text
PAGE</>:digital text page up and down
EPG: Electronic Programmer Guide used to open and close the EPG
FAV: Favorites Button used to open the favorites menu
AUDIO:To press this button, you can change the audio
language from the one selected at settings to a different language, if available.
RADIO: to switch between TV picture and FM audio signal
LANG: LANGUAGE to open or close the language menu
TEXT
ENTER
STOP
TITLE
EPG
GOTO
LANG
MIX
SUB.PAGE
ZOOM
FAV
AUDIO
AUDIO
DISPLAY
PAUSE
REVEAL SIZE
PAGE PAGE
INDEX
ANGLE SLOW
DVD MENU PROGRAM SUBTITLE
DVD SETUP
RADIO
PAUSE: to pause or play the picture
ENTER: used to confirm a selection within a menu
17
MENU SCREENS
This TV allows you to adjust any setting from the menu screens using ¡°MENU¡±,¡°VOL+/-¡±and ¡°PROG+/-¡± buttons.
Press ¡°MENU¡±button to display the menu, press¡°PROG+/-¡±to change menu from one to another, ¡°VOL+/-¡± to enter the chosen menu, press¡°PROG+/-¡±to select the item, and then press ¡°VOL+/-¡±to adjust each item. Press ¡°MENU¡± again to exit the menu mode.
PICTURE
CONTRAST
BRIGHTNESS
TINT
CH
COLOUR
SHARPNESS
COLOUR TEMP
PICTURE MODE
ADJUST SELECT EXIT
SOUND
VOLUME
COOL
NORMAL
PICTURE MENU You can adjust the contrast, brightness, tint(NTSC only) colour,sharpness. COLOUR TEMP: NORMAL / WARM / COOL PICTURE MODE: NORMAL / SOFT / RICH /CUSTOM
SOUND MENU
Enter sound menu, you can adjust VOLUME.
CH
ADJUST SELECT EXIT
TUNE
AUTO SCAN
CHANNEL 1
COLOUR SYS. PAL
SOUND SYS. B/G
CH
SKIP OFF
MANUAL
FINE TUNE
ADJUST SELECT EXIT
18
152.25MHz
152.25MHz
TUNE MENU AUTO SCAN: Press¡°VOL+/-¡±to begin auto search program, and press menu to exit auto search. CHANNEL: The number is the current channel, and you can also change channel from one to another.
COLOUR SYS. PAL/NTSC/SECAM (optional) SOUND SYS. B/G,D/K,I,M,L,L¡¯(optional)
SKIP: Set this item on to skip the channel which you are watching. MANUAL: To start searching until a program is searched, or press¡°MUNE¡± to exit. Fine Tune: Frequency data can be fine-tuned in upward or downward by the VOL+/- buttons.
MENU SCREENS
SETUP
BLUE SCREEN ON
TXT LANGUAGE WEST
ASPECT 16:9
CH
ADJUST SELECT EXIT
OSD
LANGUAGE ENGLISH
HPOS
VPOS
CH
DURATION
HALF TONE
ADJUST SELECT EXIT
SETUP MENU BULE SCREEN: You can set background ON or OFF. TXT LANGUAGE. ASPECT: You can set the picture display mode 16:9, 4:3 ,ZOOM1,and ZOOM2,PANORAMA.
OSD MENU You can choose the language, adjust the H-position, V-position, duration and halftone.
PC MENU(under PC mode only)
PC
CONTRAST
BRIGHTNESS
HPOS
CH
VPOS
CLOCK
PHASE
AUTO CONFIG
ADJUST SELECT EXIT
You can adjust the CONTRAST, BRIGHTNESS
HPOS/VPOS Press the VOL+/- buttons to adjust the picture Horizontal and Vertical position.
CLOCK Press the VOL+/- to minimize any vertical bars or stripes visible on the screen background.
PHASE When necessary, adjust the pixel phase of the picture to avoid picture interference.
AUTO CONFIG To adjust the screen position automatically. It will take a few seconds and during this process the screen will be black.
NOTE:
If the set is cold ,there may be a small¡°flicker¡± when the set is switched on. It is normal, There is nothing wrong with the set. If possible, use the VESA 1024X768@60HZ video mode to obtain the best image quality for your LCD monitor. Under other resolutions some scaled or processed pictures may appear on the screen. Some dot defects may appear on the screen, like red, green or blue Spots, However,this will have no impact or effect on the monitor performance. Do not press the LCD screen with your finger for a long time as it may incur some damage to the screen.
19
INITAL SETTINGS(DVD)
COMMON PROCEDURES OF INITIAL SETTINGS
Press SETUP button to get the setup menu. Use
direction buttons " " to select the preferred item .
After finishing settings, press SETUP again to TV
display.
The following menu items can be changed:
GENERAL: selects the GENERAL PAGE menu.
AUDIO : selects the Audio menu.
DOLBY : selects the DOLBY DIGITAL SETUP menu.
PREFERENCE: selects the PREFERENCE PAGE menu.
GENERAL SETUP PAGE
General
-- --
General Setup Page
TV display Angle Mark Osd Lang Eng
Screen Saver
Go To General Setup Page
Audio
Ps On
On
The following me u items can be changed:
Dolby
On Off
Video
English Japanese
Preference
Normal/Ps Normal/Lb
On
Wide 16:9
Off
n
TV DISPLAY: selects the aspect ratio of the playback picture. NORMAL/PS: pan scan display.
&
NORMAL/LB: letterbox display. WIDE: widescreen display. ANGLE MARK: viewing angles change option (if available). See changing the angles on page 10.
SCREEN SAVER: this is to turn on/off screen saver.
AUDIO SETUP PAGE
General
-- --
Speaker Setup Page
Downmix
Speaker Setup Page
Audio
Stereo
Dolby
Video
LT/RT Stereo
Preference
This page is for setup speaker output.
DOWNMIX Stereo
LT/RT: 2ch output, main channel with surround. STEREO: 2ch output, main right channel with right surround; main left channel with left surround.
DOLBY DIGITALSETUP PAGE
General
-- --
Dolby Digital Setup
Dual Mono
Dynamic
Go To Dolby Digital Setup
Audio
Dolby
FULL
3/4
1/2
1/4
OFF
Video
Preference
Stereo L-Mono R-Mono Mix-Mono
The following menu items can be changed: DUAL MONO: Reproduction mode, used only when the input consists of two independent audio channels(1/1 mode). Possible selections are: STEREO: Reproduce both channels as is. L-MONO: Reproduce the left channel only. R-MONO: Reproduce the right channel only. The default is STEREO. DYNAMIC: Dynamic range compression.
20
VIDEO DIGITALSETUP PAGE
General
--
Video Setup Page
Sharpness
Brightness
Contrast
Go To Video Setup Page
Audio
Low
00
00
Dolby
Video
--
The following menu items can be changed:
Sharpness: sharpness value. Brightness: brightness value. Contrast: contrast value.
Preference
High
Medium
Low
INITAL SETTINGS(DVD)
PREFERENCE SETUP PAGE
Change
Dolby
2 G 3 Pg 4 Pg 13 5 Pgr 6 R 7 Nc17 8 Adult
Video
English French Spanish Chinese Japanese Korean Russian
Preference
English French Spanish Chinese Japanese Korean Russian
English French Spanish Chinese Japanese Korean Russian
General
-- --
Preference Page
Audio Eng
Subtitle
Disc Menu Eng
Parental
Password
Default
Go To Preference Page
Audio
Reset
The following menu items can be changed:
AUDIO: Selects a language for audio(if available). SUBTITLE: Selects a language for subtitles(if available). DISC MENU: Selects a language for DISC menus (if available). PARENTAL[DVD only]: This is to disable the playing of specified DVDs which are unsuitable for children. Some
DVDs are encoded with specific rating level. If the rating level of the disc is higher than that preset in the setup operation, playback of the disc will be prohibited. After selecting one of the PARENTAL items the screen will change to the PASSWORD page, and password is required , The factory initial setting is 1369.
PASSWORD: Selects the menu setup PASSWORD CHANGE PAGE.
PASSWORD CHANGE PAGE
OLD PASSWORD [ XXXX ]
PASSWORD CHANGE PAGE
NEW PASSWORD [ YYYY ]
CONFIRM PASSWORD [ YYYY ]
OK
OLD PASSWORD: Enter the OLD password, (Factory setting is 1369), and the cursor will jump automatically to
NEW PASSWORD.
NEW PASSWORD: Enter the NEW password. Enter 4 digits from the remote control unit numeric buttons, and the
cursor will automatically jump to CONFIRM PASSWORD.
CONFIRM PASSWORD: Confirm the NEW password by entering it again. If the confirmation is incorrect, the cursor
will stay in this column. After entering, the correct new password again, the cursor will jump automatically to OK.
OK: When cursor is on this button, press ENTER key to confirm setting.
DEFAULT: Back to the factory setting.
21
DVBT SETUP MENU SETTING
General Operation&General Setup Page
First Time Installation
1 A First Time Installation Wizard appears. Press ¡°ENTER¡± to select ¡°YES¡±. 2 Press ¡°UP¡± button / ¡°DOWN¡± button to select the item you wish to set up, and then press ¡°LEFT¡± button / ¡°RIRHT¡± button to switch to your preferred setting. 3 Press ¡°UP¡± button / ¡°DOWN¡± button to select ¡° NEXT¡±, and then press¡°ENTER¡± to continue to the next page. 4 To start Auto Search, press ¡°ENTER¡± to select ¡°YES¡±. All the receivable programs (including TV and Music) will be listed respectively on the screen. This process may take a few minutes to be done. 5 After Program Search is done, press ¡°UP¡± button / ¡°DOWN¡± button to select and start watching TV programs.
No channels are stored in your unit. A First Time Installation Wizard will appear automatically on the screen. Continue with the OSD (On-Screen-Display) to do the following setting.
*To return to the MAIN MENU
---Press EXIT button. *To finish the setup operation
---Press DVBT-MENU to exit from Main Menu screen.
Main Menu
Most of the Settings of your DVB player can be done by following the OSD instructions (*Main Menu). For details on how to set up by using your remote control. In Advance: Press DVBT-MENU to display the Main Menu.
MAIN MENU
Program list Program search
Parental control System setting Game(not for sale) Accessory Personal style
22
DVBT SETUP MENU SETTING
General Setup Page
The following is the overview of the seven settings:
Program List
TV Program List Music Program List Sort
Enter parental PIN
Enter PIN
Game
GAME Mine Tetris Gomoku Calender
P erso nal S tyl e
Displ ay T ype Sc ar t Output Ant en na Po wer Count ry OSD Language
P arental Cont rol
P erso nal S tyl ePerso nal S tyl e
Menu Colo r
T ransp arency L evel
Bo rder P atter n
En tr y A nimati on
OK
BLUE
6
R ound
Ri ght
1
3
5
7
Program Search
Automatic Search Manual Search
System Setting
TV standard Display TYPE
Video output Antenna power Regional setting Language Time setting System schedule
ACCESSORY
System Information Factory Default System update
2
4
6
TV Program Editing
Before editing your TV program, make sure you have finished with program search,
which should be done by completing the First Time Installation Wizard. If not, you have
to set up your TV programs first. Please refer to¡°Program Search¡± for details.
1 Under Main Menu, press ¡°ENTER¡± to select ¡°Program List ¡±. 2 Under Program List, press ¡°ENTER¡± to select ¡°TV Program List ¡±. 3 A Program edit table Window appears. You can use this table to edit your Favorite
TV Programs, re-arrange your TV program numbers and delete the TV programs you dislike.
Switch Program Setting
Step 1. In the Program edit table, press RIGHT button / LEFT button to highlight ¡°¡±¡°¡±
¡°¡±Move section.
Step 2. Under Move section, press UP button / DOWN button to highlight the¡°¡±¡°¡±¡°¡±
corresponding program box you wish to change and press ENTER .¡°¡±
Step 3. Press UP button / DOWN button to highlight the corresponding program ¡°¡±¡° ¡± box you wish to exchange, and then press ENTER . You will see a Double-Arrows¡°¡±¡° ¡±
icon appear on this box, representing that 2 program numbers are switched.
Step 4. Repeat Step 2 through Step 3 to switch more programs.
23
DVBT SETUP MENU SETTING
Speaker Setup Page
Program Search
To Enjoy the high quality of digital TV signals through the Set Top Box, you have to search for all the available TV program first. This unit provides you with 2 ways of program search, including Automatic Search and Manual Search
Automatic Search
1 Under Main Menu, press ¡°DOWN¡± button and ¡°ENTER¡± to select ¡°Program
Search¡±.
2 Under Program Search, press ¡°ENTER¡± to select ¡°Automatic Search¡±. 3 An Automatic Search window appears on the screen. All the receivable TV/Music
programs will be listed respectively in the TV List/Music boxes below. This process may take several minutes to be done
In Advance:
After Program Search is done, you can start watching TV or listening to Music programs by pressing ¡° UP¡± button / ¡°DOWN¡± button.
Manual Search
You can locate specific programs by selecting frequency numbers.
1 Under Main Menu, press ¡°DOWN¡± button and ¡°ENTER¡± to select ¡°Program Search¡±. 2 Under Program Search, press ¡°DOWN¡± button and ¡°ENTER¡± to select ¡°Manual
Search¡± 3 An Manual Search window appears on the screen. Press ¡°RIGHT¡± button / ¡°LEFT¡± button to select¡° Channel Number ¡±,and the corresponding frequency number will show from down below. 4 Press ¡°DOWN¡± button to highlight ¡°ENTER¡±, and press ¡°ENTER¡±.
24
DVBT SETUP MENU SETTING
Dolby Digital Setup
System Setting
This function allows you to set up the normal aspect ratio (picture display shape) according to source signal and monitor format of your TV, or your own viewing preference.
Regional Settings
This function allows you to set the time zone of your location and corresponding bandwidth of the digtial signals all at once simply by selecting the country you are
currently in.
1 Under Main Menu, press DOWN button/ UP button to select System Setting .¡°¡±¡°¡± ¡° ¡± 2 Under System Setting, press ENTER button to select Regional setting .¡°¡±¡° ¡± 3 Press LEFT button / RIGHT button/ ENTER button select the country where¡°¡±¡°¡±¡°¡±
you' re in
MAIN MENU
System Setting
TV standard Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
Regional Setting
Country
OSD Language
Time Zone
England
English
GMT+08:00
OSD Language/Audio Language/Teletext language
This function allows you to set the language of your OSD (On-Screen Display) Menu. 1 Under Main Menu, press DOWN button/ UP button to select System Setting 2 Under System Setting, press ENTER button to select OSD Language 1st Audio language 2nd audio language DVB subtitle 3 Press UP button / DOWN button and ENTER to select the preferred OSD
¡±¡° ¡±¡° ¡±
¡°¡± ¡° ¡± ¡° ¡±
¡°¡±¡°¡± ¡° ¡±
¡°¡±¡° ¡±¡°
language. Audio language / DVB subtitle language.
MAIN MENU
System Setting
TV standard Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
Language
OSD language English 1st Audio language English 2st Audio language English DVB subtitle English
25
TROUBLESHOOTING TIPS
Before calling for service, you can check the following items on symptoms and solutions.
No picture:
Check other channel, maybe station problem. Adjust the tuning control. Ensure that the input setting is at TV state. Ensure that the LCD is on. Ensure that the equipment is connected properly.
No sound and distorted sound:
Ensure that the input settings for the TV and sound are proper. Adjust the tuning control. Probably local interference, such as an appliance. Re-orient aerial(if indoor type). Ensure that the equipment is connected properly.
No remote Control:
Check the battery are installed with the correct polarity. Point the remote control unit at the remote control sensor and operate. Remove the obstacles between the remote control and the remote control sensor. Operate the remote control unit at a distance of not more than 8 meters from the remote control sensor.
Troubleshooting tips(PC mode):
¡°NO SYNC SIGNAL¡± or¡°POWER SAVE¡± displayed
Check if the wire is connected correctly. Ensure the computer or other equipments are at power on mode. Ensure the computer is not at power save mode. Ensure the TV input setting is at pc mode.
¡°Invalid Scan Fred¡±displayed
Check if the input setting is compatible to the monitor specification. Check if the wire is connected correctly.
Led lamp indicator on but no picture
Check the monitor setting :contrast ,brightness. Check if the wire is connected correctly.
Some unusual spots on screen:
Some dot defects may appear on the screen, like red, green or blue, Spots, However, this will have no impact or effect on the monitor performance.
26
THE CAUSES OF INTERFERENCE
Incorporated in your TV receiver are the most up-to-date devices to eliminate interference.Local radiation however, can create disturbances which visibly affect your picture. Proper installation, a good aerial are your best safe-guards against these disturbances.
RF INTERFERENCE
Moving ripples across the screen are caused by nearby transmitting or receiving short-wave radio equipment.
DIATHERMY
Herringbone pattern and partial picture loss can result from the operation of diathermy equipment from a nearby doctor's surgery or hospital.
SNOW
Weak TV signals from long distant stations result in an instead picture and give the effect of falling snow. An antenna adjustment or antenna amplifier may be needed.
GHOST
Multiple image caused by TV signals reflected back from surrounding buildings, hills, aircraft, ect. Is minimized by correct aerial positioning.
CAR IGNITION
Nearby cars and electrical motors can cause small streaks across the picture or make the picture roll.
27
»ù±¾²Ù×÷»ù±¾²Ù×÷
Loading...