Denver BTB-410 User Manual

BLUETOOTH SPEAKER WITH LED LIGHTS

Model No.: BTB-410

Read this booklet thoroughly before using and save it for future reference

Guide to the Appliance

Unit must be fully charged before use

1. TWEETER X 2

2. FUNCTION/STANDBY

BUTTON

3. P-MODE/M./ECHO BUTTON

4. 10/M./FOLD.- BUTTON

5. /TUN.- BUTTON

6. VOL.- BUTTON

7. /TUN.+ BUTTON

8. VOL.+ BUTTON

9. /PAIR/SCAN BUTTON

10. 10/M./FOLD.+ BUTTON

11. EQ/LIGHT BUTTON

12. PARI INDICATOR

13. CHARGE INDICATOR

14. LCD DISPLAY

15. SPEAKER X 2

16. HANDLE

17. MIC VOL. KNOB

18. 6.3mm MIC JACK 1

19. 6.3mm MIC JACK 2

20. LIGHT BAR

21. 3.5mm AUX IN JACK

22. USB PORT

23. POWER ON/OFF BUTTON

24. VENTILATION HOLES

25. AC SOCKET

26. Antenna

Getting Started

POWER SOURCE

This unit works with rechargeable lead-acid battery (the battery capacity 4000mAh). Fully charge the unit (around 7 hours) before using the product for the first time. The playback time has about 2 hours after full charging. Unplug the AC Power cord from the AC socket to work on the battery pack after fully charged. Plugging the AC Power cord while the battery pack is attached initiates the charging of this battery, the charge LED indicator lights red during charging, when the battery is fully charged the indicator will turn to green. When the unit is with low battery, the LED indicator will flash in red. Warning: Do not change the battery, only high-qualified personnel can perform this operation.

OPERATION INSTRUCTION

BASIC FUNCTION

Eng-1

TURNING THE UNIT ON/OFF

Press the power ON/OFF button on the rear cabinet to switch the unit on or off. NOTE: In USB/Bluetooth/AUX mode, when the unit is not providing the main function for around 15 minutes, the unit will automatically switch into standby

mode. Press the FUNCTION/ button to turn on the unit again. Please note that low volume setting in the audio source may be recognized as “no audio signal”, this will affect the capability of signal detection from the device and can also originate an automatic switch into standby mode. If this happens please reactivate the audio signal transmission or increase the volume setting on the audio source player in order to resume playback. Electrostatic Discharge hints – The unit may reset or may not reset to normal operation mode due to electrostatic discharge, just switch it off and reconnect again.

SETTING THE FUNCTION MODE

To change the function modes, press the FUNCTION/ button repeatedly to choose USB/AUX/BLUETOOTH/RADIO function.

ADJUSTING THE VOLUME

1. Press the VOL.+ or VOL.- button to increase or decrease the music volume.

2. Rotate the MIC VOL. knob on the unit to increase or decrease the microphone volume.

EQUALIZER (EQ) FUNCTION

This unit has a built-in equalizer system, press the EQ/LIGHT button on unit to select a setting that best matches the music style: FLAT, POP, CLASSIC, JAZZ, and ROCK.

MICROPHONE ECHO ADJUSTMENT

Press and hold the P-MODE/M./ECHO button on unit to turn on or turn off the microphone echo effect. When the echo effect is on, the display will show “ECHO”.

FLASHING LIGHT

There are 5 modes for the DISCO LED lighting above the speakers. Press and hold the EQ/LIGHT button to choose the desired light mode. To turn off the light effect, press and hold the EQ/LIGHT button until OFF shows on the display. L-1: Blue LED will be on constantly when it is selected. L-2: Blue LED will be on flashing mode. L-3: Red LED will be on constantly. L-4: Red LED will be on flashing mode. L-5: 7 colors LED will be on flashing mode.

+ 3 hidden pages