Page 1
I. PARTS:
A. Fill Station Assembly
B. 4 pcs. ea. Mounting screws and anchors
C. 1 pc. Outlet Tubing, 10’ long
D. 1 pc. Tubing clamp
E. Metering Tip Kit
F. 1 pc. ea. Tubing with foot strainer, ceramic weight
G. Priming ring
H. Worm clamp (For 607-2B only)
II. INSTALLATION:
CAUTION: ALL WORK DONE SHOULD ADHERE TO ALL APPLICABLE PLUMBING CODES.
1. Hold assembly to wall, locate positions of mounting screws. Drill holes in wall about 1” deep. Mount
assembly to wall using screws and anchors provided.
2. Install priming ring in outlet tubing (large diameter), a few inches from one end. Slip tubing over threads of
injector, with priming ring close to the injector. Secure with tubing clamp and cut to convenient length.
3. Attach water supply hose (not provided) to water inlet and tighten. Note: For the 607-2B Hi-Flow Station,
attach water supply tube (not provided) to the water inlet barb and secure with worm clamp.
DEMA MODEL 607-2 & 607-2B
HI-FLOW FILL STATION
INSTALLATION INSTRUCTIONS
III. CHEMICAL ADJUSTMENT:
CAUTION: Be careful when working with hazardous chemicals.
1. Select metering tip using Table 1 as a guide. Screw tip into inlet barb of injector.
2. Cut inlet tube to convenient length, at least 18” long to insure priming but not more than 6’ (greater lifts reduce
injection capacity).
3. Slip ceramic weight over tubing and insert end with foot strainer into chemical. Attach other end to inlet barb
of injector.
Table 1: Induction readings taken at 50-psi
inlet pressure & 9 GPM.
METERING
TIPS
COLOR OZ/GAL RATIO
Clear 0.21 606.3 – 1
Purple 0.26 496.9 – 1
Yellow 0.44 288.6 – 1
Green 0.83 155.0 – 1
Pink 0.95 134.1 – 1
Turquoise 1.57 81.6 – 1
Black 2.01 63.6 – 1
Gray 2.64 48.4 – 1
Red 3.40 37.7 – 1
Blue 4.11 31.1 – 1
Brown 5.64 22.7 – 1
White 7.19 17.8 – 1
Orange 8.71 14.7 – 1
None 14.88 8.6 - 1
Induction rates may vary from product to product,
I-679 Pg. 1 of 4
Rev. E0901
1 CPS
NOTE: IN ORDER FOR UNIT TO
OPERATE PROPERLY, FLOW
RATE NEEDS TO BE 10 GPM OR
GREATER.
Page 2
field test are recommended.
DEMA MODEL 607-2 & 607-2B
HI-FLOW FILL STATION
INSTALLATION INSTRUCTIONS
RETURNS: NO MERCHANDISE MAY BE RETURNED FOR CREDIT WITHOUT DEMA’S
WRITTEN PERMISSION. RETURN MERCHANDISE AUTHORIZATION
NUMBER REQUIRED IN ADVANCE OF RETURN.
WARRANTY: DEMA products are warranted against defective material and workmanship under normal use and
service for one year from the date of manufacture. This limited warranty does not apply to any
products which have a normal life shorter than one year or failure and damage caused by
chemicals, corrosion, improper voltage supply, physical abuse, or misapplication. Rubber and
synthetic rubber parts such as “o”- rings, diaphragms, squeeze tubing and gaskets are considered
expendable and are not covered under warranty. This warranty is extended only to the original
buyer of DEMA products. If products are altered or repaired without prior approval of DEMA,
this warranty will be void.
Defective units or parts should be returned to the factory with transportation prepaid. If
inspection shows them to be defective, they will be repaired or replaced without charge, F.O.B.
factory. DEMA assumes no liability for damages. Return merchandise authorization number, to
return units for repair or replacement, must be granted in advance of return.
I-679 Pg. 2 of 4
Rev. E0901
Page 3
I-679 Pg. 3 of 4
Rev. E0901
Page 4
90-7
60-9
100-12L
90-71-10
90-73-9
73-3
90-72-1
61-9-
65-2
90-70-19U
(FOR 607-2B ONLY)
93-44
(FOR 607-2 ONLY)
61-107
100-58P
100-38
(FOR 607-2 ONLY)
16-9-6
60-49
76-2-1
(FOR 607-2B ONLY)
PART NO.
16-9-6
60-47-2
60-49
60-9
61-107
65-2
66-54
73-3
76-2-1
66-54
DESCRIPTION
TUBING CLAMP
OUTLET TUBING (1" ID X 12 FT. LONG)
PRIMING RING
SIPHON BREAKER (1/2" NPT)
CERAMIC WEIGHT (1/2" ID)
BALL VALVE (3/8" NPT)
MOUNTING SCREW & ANCHOR KIT (4 EA)
BUSHING (3/4" MPT X 1/2" FPT)
WORM CLAMP (FOR 607-2B ONLY)
60-47-2
PART NO.
90-7
90-70-19U
90-71-10
90-72-1
93-44
100-38
100-58P
100-12L
DESCRIPTION
STREET ELBOW (1/2" NPT)
HOSE BARB ( 3/8" NPT X 1/2" BARB)
REDUCING NIPPLE (3/8" NPT X 1/2" NPT)
INJECTOR ASSEMBLY
PIPE NIPPLE (1/2" NPT X 5" LONG)90-73-961-9- METERING TIP-SPECIFY SIZE
SWIVEL ADAPTER ASSY (FOR 607-2 ONLY)
STRAINER WASHER (FOR 607-2 ONLY)
FOOT STRAINER
VINYL TUBING (3/8" ID X 8' LONG)
I-679 Pg. 4 of 4
Rev. E0901
Loading...