Page 1
DEMA 5800V & 5800V.B
Choose a location on the wall that will allow gravity feed of the chemical to the dish machine. You don't want to be
more than 5' from the bottom of the Viking Bowl to the bulkhead fitting in the dish machine tank wall. The 5/8" I.D. clear
PVC tubing from the Bowl should run down to the injection point. If mounting on the side of the dish machine, use ¼-20 x
¾” bolts.
1. Use the compression nut (E) on the fitting on top of the Viking Bowl to secure the stainless steel tube to the Bowl. Attach
the stainless steel tube to the ELBOW fitting in the side of the plastic or metal vacuum breaker.
2. Mount the Viking Bowl using screws and anchors provided. Allow enough room above the bowl to insert and remove
containers of product.
3. Run and secure a 1/4" OD water line from the output side of your detergent control solenoid or timer valve to the straight
fitting in the bottom of your plastic or metal vacuum breaker – this is the vacuum breaker inlet fitting. NOTE: Do NOT
tap a hot water line AFTER a booster heater for a feed line to the solenoid and Bowl. The temperature of the water that
will flow to the bowl must not exceed 140 degrees Fahrenheit.
4. On the side of the dish machine tank, locate or make (with a Greenlee punch) a 7/8" hole for the 77-degree elbow above
the water line. Try to dispense in an area with good water circulation. A good location is across from the inlet to the
circulation pump. Avoid installing in the tank corners. Install the elbow assembly in this hole.
5. Attach the clear feed tubing to the bottom of the Viking Bowl. Pull the other end of the tubing in line with the elbow and
cut off any extra so the line doesn’t sag. Attach it to the elbow.
6. Power the detergent dispenser and check for leaks at all connections. Tighten any loose compression nuts. A small
trickle of water from the spray nozzle is normal when the solenoid / timer valve is active and no product container is in
place.
Water Pressure: Minimum 15 PSI / Maximum 40 PSI Dynamic
Water Temperature: Some solid products are run with cold water. We do not recommend using water that is
Notes:
- The Viking Bowl accepts a standard 6” jug with a 100MM neck finish.
- Colored Viking Bowls are available – call for details.
- Private label logo is available on the Viking Bowl - call for details.
- Viking manufactures screen caps for encapsulated detergent - call for details.
Nozzles:
- The Viking Bowl comes with a Standard Spray Nozzle installed. The standard nozzle is used for both powder and solid
products.
- The Cone Nozzle provides the same spray pattern as the Standard Nozzle but it is cone shaped to shed water and product
after feeding is complete.
- The Powder Nozzle provides a low flat spray and should be used with powdered products only.
- The NDB Nozzle is for locations where low water pressure is too low. It has a smaller orifice and will provide a better
spray pattern at lower pressures. It will produce lower flow rates than any of the other nozzles.
I-1029 Rev. A-37101 7/28/11 www.demaeng.com www.viking-injector.com Page 1 of 2
VIKING BOWL INSTALLATION INSTRUCTIONS
SPECIFICATIONS & RECOMMENDED OPERATING CONDITIONS
If necessary, pressure can be adjusted by installing an in-line regulator to control the water
pressure to the Viking Bowl.
more than 140 degrees Fahrenheit.
Page 2
VIKING BOWL PARTS LIST
ITEM
NO.
DESCRIPTION
DEMA PART
NO.
VIKING PART NO.
1 SPRAY ARM WITH BRASS PLUG 58.300 VOA INTPLUG V80
2 STAINLESS STEEL BALL 58.301 CHA VKBSSBL 000
3 MPT FITTING WITH O-RING 58.302 VOA NY11MPT V81
4 ¼” JACO NUT W/ RING & FERRULE 58.303 CHA 1/4JACP 000
5 PLATED BRASS COLLAR 58.304 CHA VBBRCOL 000
6 FLIPPER / PADDLE SPRING 58.305 CHA SPRAYSP 000
7 SAFETY FLIPPER / PADDLE 58.306 MOA VBFLPR M71
8 7.5” STAINLESS STEE TUBE 58.307 CHA VKBWLTB 000
PLASTIC DEMA VACUUM BREAKER 58.308 VOA VVBDEMA V19
9
OPTIONAL WATTS 288AC ¼”
VACUUM BREAKER WITH FITTINGS
58.309 VOA BRVBWFT V55
COMPLETE
10 #8 X ½” HI/LOW SS SCREW 58.310 CHA 8X1/2SS 000
11 STANDARD NOZZLE (PWD. & SOL) 58.311 VOA STDNOZ V71
12 5’ LENGTH OF 5/8” X 7/8” TUBING 58.312 CBA 5’#26TB 000
13 BLANK GREY FACEPLATE 58.313 M OA VBFCP LT M7 3
14
COMPLETE SPRAY ARM (INTERNAL
ASSEMBLY INCL 1-7 + 11)
58.314 VOA VBINTAS V49
15 POWDER NOZZLE (POWDER ONLY) 58.315 VOA POWDNOZ V73
16 CONE NOZZLE (POWDER & SOLID) 5 8.316 VOA CONENOZ V70
17 NDB NOZZLE (FOR LOW PRESSURE) 58.317 VOA NDBNOZ V72
18
ELBOW (BULKHEAD) FITTING
COMPLETE
58.318 VOA 77ELAS V41
19 STANDARD HARDWARE BAG 58.319 CHH VB HARDW 000
I-1029 Rev. A-37101 7/28/11 www.demaeng.com www.viking-injector.com Page 2 of 2
Loading...