Last Update ALLU 03/06/2015
Installation Instruction
DEEP RINGO S LED SOFT S1
A
A
B
B
A
+
1
Ref: 202 28 28120
79
79
79
PLASTERKIT 161 200 x 200 175 x 175
207 01 161
CONCRETE BOX 161 202 x 202 x 186 207 x 207
270 11 161
Enkel geschikt voor toestellen op zeer lage spanning (minder dan 50 V AC)
Convient uniquement pour les produits à très basse tension (moins de 50 V AC)
Geeignet für Güter mit sehr niedriger Spannung (unter 50 V AC)
Only suited for goods at very low voltage (below 50 V AC)
Se recomieda únicamente para aquellos productos de tensión muy baja (menos de 50 V AC)
Vale unicamente per i prodotti a tensione molto bassa (inferiore a 50 V AC)
75 x 75 x 90
max.25
0-25mm
75
90
Tc
Tc = 80°C max
Beschermd tegen vaste voorwerpen die groter zijn dan 12 mm
Protégé contre les objets solides de plus de 12 mm
Geschützt gegen Festkörper größer als 12 mm
Protected against solid objects greater than 12 mm
Protegido contra objetos sólidos superiores a 12 mm
Protetto contro oggetti solidi più grandi di 12 mm
Beschermd tegen vaste voorwerpen die groter zijn dan 1,0 mm - Beschermd tegen sproeiwater
Protégé contre les objets solides de plus de 1,0 mm - Protégé contre les pulvérisations d'eau
Geschützt gegen Festkörper größer als 1,0 mm - Geschützt gegen Sprühwasser
Protected against solid objects greater than 1,0 mm - Protected against spraying water
Protegido contra objetos sólidos superiores a 1,0 mm - Protegido contra agua pulverizada
Protetto contro oggetti solidi più grandi di 1,0 mm - protetto contro gli spruzzi d' acqua
MOUNTING KIT 75
117 x 117 x 22
Ø121
202 00 75
1
SOFT DIM
ELECTRICAL CONNECTION
-
+
-
+
FE
Falling Edge dimming
ONLY WITH
POWER SUPPLY
300 90 915 ED8
220-240V / 50-60Hz
650mA / 10W / 12-16Vdc
75 x 75 x 90
2
3
2
Ref: 202 28 28120
Installation Instruction
4
on
o
- Use only power supplies that are certied according to the applicable IEC or UL safety standards.
- Use only SELV power supplies.
- Check the ratings of the power supply with those of the luminaire.
The maximum current rating must be taken into account.
The indicated typical voltage must not be used to select a constant voltage power supply but is indented to used
to select a constant current power supply that is able to cover that typical voltage.
- Take appropriate ESD measures. Avoid touching bare conductors.
- Leds or led luminaires that require a current controlled power supply must never be connected in parallel.
- Leds can be damaged by the contact with certain chemicals or chemical gasses.
Therefore led domes or led engines should never be cleaned with chemical substances.
The following substances have proven to have a negative inuence on the performance and
must not be used in the direct environment of a led luminaire.
Methyl acetate or ethyl acetate (i.e., nail polish remover)
Cyanoacrylates (i.e., “Superglue”)
Glycol ethers (including Radio Shack® Precision Electronics Cleaner - dipropylene glycol monomethyl ether)
Formaldehyde or butadiene (including Ashland PLIOBOND® adhesive)
Dymax 984-LVUF conformal coating
Loctite Sumo Glue
Gorilla Glue
Bleach, Bleach-containing cleaners, sprays
Loctite 384 adhesive
Loctite 7387 activator
Loctite 242 threadlocker
- Remove insulation and/or provide sucient ventilation so that the indicated max Tc is not surpassed.
- Leds are susceptible to switching transients. Therefore switching must be done in the primary circuit
of the power supply.
- DELTA LIGHT recommands to use the power supplies that are indicated in the Lighting Bible.
- Respect polarity
- Don’t test LED luminaires one by one on a powersupply that is switched on.
DO NOT TOUCH OR CLEAN THE LED ARRAY!
!
Loading...