50 13 266900
Sub-1G module
PPM N1U_SB1
Essential Points for Safety
・ Request a specialist to dispose of the product.
・ Take care to ensure no water or other liquid gets on the SUB_1G.
・ The product may malfunction or may be damaged by static electricity. Be sure to remove any static electricity on the body, through such means
as touching a metal object nearby, prior to coming into contact with the product.
・ Store the product in a location with the temperature ranging between -30 and +70°C , with the humidity ranging from 30 to 85% RH.
Do not install the product in the following places:
・ Do not expose to extreme fluctuation temperature.
・ Do not expose to salt air.
・ Do not expose to corrosive substances, explosive / flammable GAS, chemicals.
・ Do not install in direct sunlight.
・ Do not install in a place exceeding the operating temperature range (-25 to +55°C)
・ Do not install above 3000m MSL or higher.
・ Do not expose to water vapor, oil vapor, smoke, cotton dust, metal powder, sawdust.
※If installed outdoor, please put it in box which is suitable for outdoor use.
.
Quick Installation Guide
Warning
Do not allow any fire producing objects to be near the product, or apply any spray, including combustible gases, to the product.
The product may ignite or explode in the unlikely event such an occurrence takes place.
Do not touch the product with wet hands. The product may cause injury due to electric shock or equipment malfunction may occur in
the unlikely event such an occurrence takes place.
Do not disassemble or modify the product. The product may cause injury or fire due to electric shock in the unlikely event such an
occurrence takes place.
When installing the SUB_1G on a wall made of materials that are not wood, be sure to acquire plastic anchors available on the
market to secure SUB_1G on the wall surface. There is danger of injury from the product falling in some rare cases.
Do not install the product in the following types of locations:
There is danger of burnout in some rare cases.
・Locations that are exposed to rain water, such as outdoors or under eaves and the like.
・Locations that are exposed to steam or where the moisture level is 30 to 85% RH, such as lavatories, changing rooms, work sites ,
kitchens and the like.
Do not use organic solvents (paint thinners, benzene and the like), strong alkaline substances or strong acidic substances to clean the
case of the product. There is danger of discoloring the case or the equipment malfunctioning in some rare cases.
Do not install the product in a place that is subject to significant effects of vibration and impact.
There is danger of injury from the product falling in some rare cases.
Scope of Delivery
NO.
Product
name
Caution
Qty Remarks Shape
SUB_1G Module
■ SUB_1G Module
1
2
Quick Installation
3
4
SUB_1G
Antenna
Guide
Screw SUB_1G screws
1 unit Main unit
1 piece
1 copy
2 pieces
Install antenna to enhance
Wireless Signals.
Installation guide
Name
Network standard support
Data rates
Modulation techniques
Bandwidth
Explanation
FCC/CE/TELEC/NCC
5860bps (BW: 500kHz)
2930bps (BW: 250kHz)
FSK/OOK
FCC: 500kHz
CE: 250kHz
TELEC: 500kHz
NCC: 500kHz
SUB_1G Antenna
FCC Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation
FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
FCC Section 15.105 Information to the user.
NOTE:
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE :
FCC Radiation Exposure Statement :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Installation Diagram
■ Install antenna to enhance Wireless Signals.
The top of the antenna must face up toward the sky.
SUB_1G Antenna
LED Description
■ Install SUB_1G to Data collector.
2
1
2
* Screw torque required for
assembling: 0.6 N.m
2
1
2
Status
Upgrade N1
Upgrade Module
No Host
Module Not Ready
Ext. Idle
Int. Idle
Normal
Power ON
Red LED
Slow Flash
Slow Flash
OFF
Slow Flash
OFF
OFF
OFF
Yellow LED
OFF
Slow Flash
Slow Flash
OFF
ON
Slow Flash
OFF
Light Green LED
OFF
Green LED
Slow Flash
OFF
Slow Flash
OFF
OFF
OFF
ON
Description
Update N1 card.
Update RF module.
No back-end devices are connected.
Waiting for module initialization.
No Ext. data transmission for more than 300 seconds.
No Int. data transmission for more than 600 seconds.
Connecting.
Description
When the device is receiving power.
Powered off.
Version 01181025