PG-04
A2A
Pulse Generator Card for VFD-V Series
Instruction Sheet
1-1 PG-04 Appearance
O
u
t
p
u
V
P
t
t
e
r
m
i
n
a
l
Input terminal
CH1
A1A1B1
Z1
B1
Z1
Pulse input terminal
Power
VP
2 B2
CH2
B2
1-2 Explanations of the terminals of PG-04 Card
Terminals Explanation
VP
Output voltage of encoder: +12V±5% 200mA
DCM Common point of the power supply and the signal
A1,
A1
B1
B1,
Z1
Z1,
A2,
A2
B2
B2,
A/O, B/O,
Z/O
The input signal of encoder (select output type of the encoder from FJP1)
The power supply can be single-phase and 2-phase and the Max. is
500KP/Sec.
The input signal of encoder (select output type of the encoder from FJP4)
The power supply can be single-phase and 2-phase and the Max. is
500KP/Sec.
The output signal of encoder can set the dividing frequency by using
parameter 10-20.
The Max. output of Open Collector is DC24V 100mA.
Grounding
1
1-3 Wiring Notes
1. Using the shielded wire to prevent interference, and do not line up in parallel with
circuits of AC200V or above.
2. Recommended wire size: 0.21~0.81mm
3. Wire length
The Output Types of the Encoder Max. Wire Length Wire Gauge
2
(AWG24~AWG18).
Voltage 50m
1.25mm
2
(AWG18) or above
Open Collector 50m
Line Driver 300m
2
1.25mm
(AWG18) or above
Complementary 70m
2
1-4 Wiring Examples
Wiring Diagram 1
Non-Fuse breaker
NFB
R
S
T
-
+1
R/L1
S/L2
T/L3
Jumper
+2/B1
Braking Resistor(Option)
B2
U/T1
V/T2
W/T3
W
U
V
Motor
M
3~
FWD/STOP
REV/STOP
Multi-step1
Factory Default
Multi-step2
Multi-step3
Multi-step4
Reset
E.F.
Digital common
MPG
10-08
10-12
Line driver
Main circuit (power) terminals
24V
FWD
REV
Mi1
Mi2
Mi3
Mi4
Mi5
Mi6
DCM
VP
A2
A2
B2
B2
DCM
Control circuit terminals
VP
Multi-function input terminals
DCM
A1
A1
B1
B1
Z1
Z1
VP
DCM
A/O
B/O
Z/O
PG
Line driver
Line driver encoder
Shielded leads & Cable
3
Wiring Diagram 2
Non-Fuse breaker
NFB
R
S
T
-
+1
R/L1
S/L2
T/L3
Jumper
+2/B1
Braking Resistor(Option)
B2
U/T1
V/T2
W/T3
W
U
V
Motor
M
3~
FWD/STOP
REV/STOP
Multi-step1
Factory Default
Multi-step2
Multi-step3
Multi-step4
Reset
E.F.
Digital common
EH-PLC
Y0
Y0
Y1
Y1
COM
Y0
Y0
Y1
Y1
Phase difference
Main circuit (power) terminals
24V
FWD
REV
Mi1
Mi2
Mi3
Mi4
Mi5
VP
Multi-function input terminals
DCM
A1
A1
B1
B1
Z1
PG
Line driver
Z1
Mi6
DCM
Line driver encoder
VP
A2
A2
B2
B2
DCM
o
90
Control circuit terminals
DCM
A/O
B/O
Z/O
Shielded leads & Cable
Recommended Wiring for Resistors
Pull High Resistor
VP
A/O
B/O
Z/O
DCM
4
330
330 330
1-5 Installation
For 1-5HP For 7.5 HP and above
Step 1: Insert 3 PCB supports into control board.
Step 2: Press the PG card on the control board to be fixed to tighten the 3 screws with a
torque of 4-6kgf-cm. If the PG card is not fixed on the control board, it may cause
screw idle running and cannot turn the screw into supports.
5
1-6 The corresponding output types of encoder
Output Types of the Encoder FJP1 FJP4
VCC
Voltage
Open collector
Line driver
VCC
VCC
O/P
0V
O/P
0V
TP
oc
TP
oc
TP
oc
TP
oc
Q
TP
oc
Q
TP
O/P
oc
TP
oc
TP
oc
Complementary
0V
ASIA
DELTA ELECTRONICS, INC.
TAOYUAN Plant/
31-1, SHIEN PAN ROAD,
KUEI SAN INDUSTRIAL ZONE TAOYUAN
333, TAIWAN, R.O.C
TEL: 886-3-362-6301
FAX: 886-3-362-7267
6
NORTH/SOUTH AMERICA
DELTA PRODUCTS CORPORATION
Sales Office/
P.O. BOX 12173, 5101 DAVIS DRIVE, RTP,
NC 27709, U. S. A.
TEL: 1-919-767-3813
FAX: 1-919-767-3969
2007-07-16
5011614303-G4E3
EUROPE
DELTRONICS (Netherlands) B.V.
Sales Office/
Industriegebied Venlo Nr. 9031,
Columbusweg 20, NL-5928 LC Venlo
The Netherlands
TEL: 31-77-324-1930
FAX: 31-77-324-1931
Loading...