LVTTL Tx Disable input and Rx Signal Detect
output
Description
DELTA’s GE-PON OLT transceiver
OPEP-33-B4L3R is designed for Gigabit Ethernet
Passive Optical Network transmission.
The module is contained in a 2x5 SFF
package with a 9/125um SC pigtail single mode
fiber.
The module consists 1490nm un-cool DFB
laser, InGaAs/InP APD, Preamplifier and WDM filter
in a high-integrated optical sub-assembly, and it
receives up to 1.25Gbps of burst-mode data at
1310nm, and transmits 1.25Gbps of continuous
data at 1490nm.
Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Application
IEEE 802.3ah 1000BASE-PX20-D
GE-PON OLT
Burst Mode Application
FTTx WDM Broadband Access
OPEP-33-B4L3R data link more than 20km in
9/125um single mode fiber.
DELTA ELECTRONICS, INC.
1 Revision: S1
03/27/2007
www.deltaww.com
OPEP-33-B4L3R
1. Absolute Maximum Ratings
Parameter SymbolMin. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Storage Ambient Humidity HA 5 95 %
Power Supply Voltage VCC -0.3 4 V
Signal Input Voltage -0.3 Vcc+0.3V
Receiver Damage Threshold +4 dBm
Lead Soldering Temperature T
Lead Soldering Time t
260 ºC
SOLD
10 sec
SOLD
2. Recommended Operating Conditions
Parameter SymbolMin. Typ. Max. Unit Note
Ambient Operating Temperature TA 0 70 ºC
Ambient Humidity HA 5 95 %
Power Supply Voltage VCC 3.13 3.3 3.47 V
Power Supply Current ICC 350 mA
Power Supply Noise Rejection 100 mVp-p
Data Rate
1.25
-100ppm
1.25
1.25
+100ppm
Gbps
Transmission Distance 20+ km
Without air flow
Non-condensing
100Hz to 1MHz
3. Specification of Transmitter
Parameter Symbol Min. Typ. Max. Unit Note
Average Launched Power (B.O.L) PO
Average Launched Power (E.O.L) PO
Launched power (Peak.) PP
Extinction Ratio ER
λ
σ
C
Center Wavelength
Spectrum Width (-20dB)
Side Mode Suppression Ratio SMSR 30 dB
Transmitter OFF Output Power P
Off
Optical Rise/Fall Time tr/tf 260 ps Note (3)
Total Jitter tJ 153 ps Note (4)
Optical Return Loss Tolerance ORLT 15 dB
Relative Intensity Noise RIN15OMA -115 dB/Hz
Optical Transmitter Reflectance -10 dB
Transmitter and Dispersion Penalty TDP 2.3 dB
Output Eye Mask
{X1,X2,Y1,Y2,Y3}
Compliant with IEEE 802.3ah
{0.22,0.375,0.20,0.20,0.30}
Note (1). Launched power (avg.) is power coupled into a single mode fiber with master connector.
B.O.L=Before of Life; E.O.L= End of Life
Note (2). The 20dB width for SLM Laser is taken as 6.07 times the RMS width
Note (3). These are unfiltered 20-80% values.
7
Note (4): Measure at 2
-1 NRZ PRBS pattern
+3 +7
+2 +7
+10
9
dBm Note (1)
dBm Note (1)
dBm
dB
1480 1490 1500 nm DFB Laser
0.44 nm Note (2)
-39
dBm
Note (5)
DELTA ELECTRONICS, INC.
2 Revision: S1
03/27/2007
www.deltaww.com
N
N
Note (5). Transmitter eye mask definition
OPEP-33-B4L3R
1+ Y 3
1
1- Y1
0.5
ormalized Amplitude
- Y2
Y1
0
X1 X2
ormalized Time
1- X2
1- X1
1
4. Specification of Receiver
Parameter Symbol Min. Typ. Max. Unit Note
Input Optical Wavelength
λ
IN
Receiver Sensitivity PIN
Input Saturation Power (Overload) P
SAT
Signal Detect -Assert Power PA - -30 dBm
Signal Detect -Deassert Power PD -44 dBm Note (2)
Signal Detect Hysteresis PA-PD 0.5 2 6 dB
Data Output Rise/Fall time tr/tf 260 ps Note (3)
Receiver Reflectance -12 dB
Receiver Threshold Setting Time T
RTS
Guard Time GT 0 128 ns
Dynamic Range DR 21.5 dB
Note (1). Measured with Light source 1310nm, ER=9dB; BER =<10
This assurance should be met with asynchronous data flowing out of the optical transmitter of
the system under test. The output data pattern from the transmitter of the system under test is a
repetition of alternate 0/1 pattern as defined for this measurement.
Note (2). When SD deasserted, the data output is Low-level (fixed)
Transmitter
Total Supply Current ICC A mA Note (1)
Differential line input Impedance RIN 80 100 120 Ohm
Differential Data Input Swing VDT 400 1600 mV
Data Input Voltage- High VIH-VCC -1.165 -0.880V
Data Input Voltage- Low VIL-VCC -1.810 -1.475V
Transmitter Disable Input-High V
Transmitter Disable Input-Low V
2 Vcc V
DISH
0 0.8 V
DISL
Receiver
Total Supply Current ICC B mA Note (1)
Differential Data Output Swing VDR 400 1800 mV
Data Output Voltage-High VOH-VCC -1.085 -0.880V
Data Output Voltage-Low VOL-VCC -1.830 -1.555V
Signal Detect Output Voltage-High V
Signal Detect Output Voltage-Low V
2 Vcc+0.3V
LOSH
0 0.8 V
LOSL
Note (1). A (TX)+ B (RX) = 350mA (Not include termination circuit)
p-p
LVPECL
LVTTL
p-p
LVPECL
LVTTL
4 Revision: S1
03/27/2007
DELTA ELECTRONICS, INC.
www.deltaww.com
OPEP-33-B4L3R
6. Pin Description
Tx/Rx Pin No. I/O Pin Name Description
1
2
Rx
Tx
3 O
4 O
5 O
6
7
8 I
9 I
10 I
VeeR
VccR
SD Normal Optical Input indicated by logic “High”, and No Optical
RD(n)
RD(p)
VccT
VeeT
Tx_Dis
TD(p)
TD(n)
MS
Receiver Ground
+3.3V Receiver Power Supply
Input indicated by logic “Low”.
Inverted Receiver Data Output
Non-Inverted Receiver Data Output
+3.3V Transmitter Power Supply
Transmitter Ground
LVTTL Logic “High” or “Open” to Disable Transmitter, and Enable
Transmitter by Logic “Low”.
Non-Inverted Transmitter Data Input
Inverted Transmitter Data Input
Mounting studs/ connect this pin to Chassis ground
MS
Bottom View
MS
DELTA ELECTRONICS, INC.
5 Revision: S1
03/27/2007
www.deltaww.com
7. Recommended Interface Circuit
OPEP-33-B4L3R
DELTA GEPON OLT Modul e
Tx_Di s
Protocol IC
SerDes IC
3.3V
10uF
3.3V
130ohm
100nF
Z0=50o hm
Z0=50o hm
150ohm150ohm
82ohm
1uH
Z0=50ohm
1uH
3.3V
82ohm
100nF
100nF
82ohm
3.3V
10uF100nF
100nF
130ohm
130ohm
6. VccT
8. Tx_Dis
9. TD(p)
Transmitter
10. TD(n)
7. VeeT
2. VccR
5. RD(p)
SD
DELTA ELECTRONICS, INC.
130ohm
3.3V
Z0=50ohm
82ohm
6 Revision: S1
4. RD(n)
3. SD
1. VeeR
www.deltaww.com
Receiver
03/27/2007
OPEP-33-B4L3R
8. Outline Dimensions
Parameter Unit Description Note
Mechanical Dimensions mm 49.5x13.34x9.6
Connector Type - SC/UPC connector IEC-61754-4
Minimum Fiber Bending Radius mm 20
Maximum Fiber Contact Temperature ºC 85
Tensile Force on Pigtail Kg 1
Maximum Fiber Stress Allowance kpsi 200
Fiber length (L) mm 540 +/-20