Delta Electronics OPBD-155E1J1R User Manual
1x9 Bi-Directional Transceiver Module for Fast
Ethernet, ATM, SONET OC-3/SDH STM-1
OPBD-155E1J1R
Description
FEATURES
RoHS compliant
Industry Standard 1 x 9 Footprint
Single Mode Fiber, Bi-Directional
Transmission with 1310nm Transmitter and
1550nm Receiver
Link Distance up to 15km
Single +5V power supply and PECL logic
interface
Wave Solderable and Aqueous Washable
Bellcore GR-468 compliant
Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Application
DELTA’s 1x9 Bi-Directional transceiver is
designed for point-to-point Bi-Directional Optical
Network transmission. The module consists
1310nm FP laser, InGaAs PIN, Preamplifier and
WDM filter in a high-integrated optical
sub-assembly, and it receives up to 155Mbps of
continuous data at 1550nm, and transmits
155Mbps of continuous data at 1310nm.
The module is contained in a 1x9 industry
standard package with a SC receptacle connector,
and support PECL electrical signal Interface and
receiver signal detect output.
1 Revision: S2
DELTA ELECTRONICS, INC.
TTC TS-1000
ITU-T G.985
IEEE 802.3ah 100BASE-BX/ Fast Ethernet
SONET OC-3/SDH STM-1/ ATM Network
FTTx Broadband Access System
Performance
OPBD-E1J1R data link up to 15km in 9/125um
single mode fiber.
03/09/2007
www.deltaww.com
Optica
esse
Spec
G.957
OPBD-155E1J1R
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Operating Ambient Temperature Ta -10 80 ºC
Storage Ambient Humidity HA 5 95 %
Power Supply Voltage VCC -0.5 6 V
Signal Input Voltage -0.3 Vcc+0.3 V
Optical Input Power (Peak) 0 dBm
Lead Soldering Temperature T
Lead Soldering Time t
260 ºC
SOLD
10 sec
SOLD
2. Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Ambient Operating Temperature TA 0 70 ºC
Ambient Humidity HA 5 85 %
Without air flow
Non-condensing
Power Supply Voltage VCC 4.75 5 5.25 V
Power Supply Current ICC 250 mA
Power Supply Noise Rejection 100 mVp-p
100Hz to 1MHz
Data Rate 10 155.52 Mbps
Transmission Distance 15 km
3. Optical Specification of Transmitter
Parameter Symbol Min. Typ. Max. Unit Note
Average Launched Power PO
Launched power (Peak.)
Extinction Ratio ER
Center Wavelength
Spectrum Width (RMS)
λ
σ
C
-14 -11 -8
-5
8.5
dBm Note (1)
dBm
dB
1260 1310 1360 nm FP Laser
6
nm
Optical Rise/Fall Time tr/tf 1.3 ns Note (2)
Total Jitter tJ 1 ns Note (3)
Optical Return Loss Tolerance ORLT 14 dB
Relative Intensity Noise RIN -116 dB/Hz
Output Eye Mask
Compliant with Bellcore TR-NWT-000253
and ITU recommendation G.957
Note (4)
Note (1). Launched power (avg.) is power coupled into a single mode fiber.
Note (2). These are unfiltered 20-80% values.
Note (3). Measure at 2
Note (4). Eye Mask definition
23
-1 NRZ PRBS pattern
1.20
1.00
0.80
e
d
u
t
0.50
i
l
p
m
0.20
A
0.00
-0.20
l Pulse Mask with B
Mean level of logical "1"
Mean level of logical "0"
0.350.150.00
Time
0.65
l Filter
0.85
1.00
ified in ITU-T
DELTA ELECTRONICS, INC.
2 Revision: S2
03/09/2007
www.deltaww.com
OPBD-155E1J1R
4. Optical Specification of Receiver
Parameter Symbol Min. Typ. Max. Unit Note
λ
Input Optical Wavelength
IN
Receiver Sensitivity PIN
Input Saturation Power (Overload) P
-3 dBm
SAT
Signal Detect -Assert Power PA - -30 dBm
Signal Detect -Deassert Power PD -44 dBm Note (2)
Signal Detect Hysteresis PA-PD 0.5 2.5 6 dB
Optical Receiver Reflectance -14 dB Note (3)
Output Data Rise/Fall time tr/tf 1.5 ns Note (4)
S/X Endurance 10 dB Note (5)
Optical Isolation 25 dB Note (6)
Note (1). Measured with 1520nm, ER=10dB; BER =<10
Note (2). When SD deasserted, the data output is Low-level (fixed)
Note (3). When the terminal is viewed from the optical path, the reflection toward the optical path of the
optical signal with a central wavelength of 1480nm to 1580nm transmitted to terminal.
Note (4). These are 20%~80% values
Note (5). X=10 MHz, Rectangular BER =10
-10
Note (6). Receiver isolation between 1260nm ~1360nm
1480 1600 nm PIN-PD
-30
-10
@PRBS=223-1 NRZ
dBm Note (1)
5. Electrical Interface Characteristics
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Total Supply Current ICC A mA Note (1)
Differential line input Impedance RIN 80 100 120 Ohm
Differential Data Input Swing VDT 300 1600 mV
Data Input Voltage- High VIH-VCC -1.165 -0.880 V
Data Input Voltage- Low VIL-VCC -1.810 -1.475 V
Receiver
Total Supply Current ICC B mA Note (1)
Differential Data Output Swing VDR 400 2000 mV
Data Output Voltage-High VOH-VCC -1.085 -0.880 V
Data Output Voltage-Low VOL-VCC -1.830 -1.555 V
Signal Detect Output Voltage-High VOH-VCC -1.085 -0.880 V
Signal Detect Output Voltage-Low VOL-VCC -1.830 -1.555 V
Note (1). A (TX)+ B (RX) = 250mA
(A: Not include termination circuit; B: using a resister of 270Ω between Data-output and ground)
p-p
PECL
p-p
PECL
DELTA ELECTRONICS, INC.
3 Revision: S2
03/09/2007
www.deltaww.com
Loading...