Delta Electronics LMWA200 User Manual

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

Wireless PCI Adapter

User Manual

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna, (2) Increase the separation between the equipment and receiver, (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, (4) Consult the dealer or an experienced radio/TV technician for help.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

Wireless PCI Adapter

TABLE OF CONTENT

INTRODUCTION .............................................................................1

CONNECT THE PCI ADAPTER TO YOUR DESKTOP PC ...... 2

ARDWARE INSTALLATION

DRIVER INSTALLATION............................................................... 3

NSTALL DRIVER UNDER WINDOWS

CONFIGURATION UTILITY .......................................................31

NSTALL THE CONFIGURATION UTILITY

ONFIGURE THE CONFIGURATION UTILITY

...............................................................2

98 ............................................3

ME ..........................................7

2000 ......................................10

NT ......................................... 14

XP .........................................28

..........................................31

....................................34

Wireless PCI Adapter

Introduction

The Wireless PCI Adapter solution overcomes the limitations of wired networks by providing fast, simple, mobile and reliable access. It is designed for desktop computers running Windows 98, 2000, NT V4.0 SP6, Millennium and XP.

Features

 11 Mbps High-Speed Transfer Rate  Interoperable with IEEE 802.11b(DSSS) 2.4GHz-compliant

Equipment

 Plug-and Play Operation Provides Easy Setup  Utilizes Intersil Prism 2.5 chip sets  Advanced Power Management Features Conserve Valuable

Notebook PC Battery Life

 Direct Sequence Spread Spectrum Compatible to Prevent Lost

Connections

 Rugged Metal Design with Integrated Antenna  Wired Equivalent Privacy (WEP) 64-bit or 128-bit data

encryption

 Driver Supports Windows 98, Millennium, NT V4.0 SP6, 2000

and XP

iii

Wireless PCI Adapter

Connect the PCI Adapter to Your Desktop PC

Hardware Installation

 Shut down your desktop PC.  With the PC Card’s 68-pin connector facing the PCI Adapter’s

slot and the “Network PC Card” label facing up, slide the PC Card completely into the PCI Adapter.

 Open your PC case and locate an available PCI slot in the

motherboard.

 Slide the PCI Adapter into the PCI slot. Make sure that all of its

pins are touching the slot’s contacts. You may have to apply a bit of pressure to slide the card all the way in. After the card is firmly in place, secure its fastening tab to your PC’s chassis with a mounting screw. Then, close your PC.

 Power on your desktop PC.  Insert the driver CD into your CD drive.  The Hardware Installation is complete.

Wireless PCI Adapter

Driver Installation

Install Driver Under Windows 98

1. Windows 98 will automatically recognize a new PCI Network Controller device. Click the Next button to proceed.

2. Windows will notify you that it is unable to locate the driver and will ask you to specify where the driver is located. Click the Other Location button to select the driver’s location.

Wireless PCI Adapter

3. This will bring you to the Select Other Location screen. Click the Browse button to select the driver’s location. At this point, Windows will ask you to browse for the driver’s folder. Simply select the folder in which the driver is located.

4. Windows is now ready to install the driver. Click the Next button to continue.

Wireless PCI Adapter

5. Windows has now completed installing the network. Click the Finish button to continue.

6. After installing the drivers, the System Setting Change screen will show you that installation is complete. Click the Ye s button to finish.

Wireless PCI Adapter

7. Click right on My computer and select properties. Select Device Manager and click on the Network adapters. You will

find the LM-WA200 IEEE 802.11 PCI Card if it is installed successfully. The PCI Adapter driver installation is finished.

Wireless PCI Adapter

Install Driver Under Windows ME

1. Windows automatically recognizes a new PCI Adapter added. Select Automatic search for a better driver [Recommended] and click the Next button to proceed.

2. At this point, Windows will ask for the cw10.sys file. Browse the driver of the CD-ROM.

Wireless PCI Adapter

3. Windows will notify that installing has been completed. Click the Finish button to continue.

4. Windows will now ask you to restart your computer. Click the Ye s button to restart.

Wireless PCI Adapter

5. To verify the driver installation, Move cursor on “My computer” icon and click the right button of the mouse. Select the properties. The System Properties windows shows. Click the Network adapters on the Device Manager folder. LM-WA200 IEEE 802.11 PCI Card will be found if the driver installation is

successful.

Wireless PCI Adapter

Install Driver Under Windows 2000

1. Windows 2000 will automatically recognize the PCI Adapter, once it is connected to the PC, and prompt you to install the necessary driver. Click the Next button to proceed.

Wireless PCI Adapter

3. Select Specify a location and click the Next button.

4. Click the Browse button and select the folder in which the driver is located. Click the OK button.

2. Select Search for a suitable drive and click the Next button. This will search for the Windows 2000 driver.

+ 14 hidden pages