Delta Electronics LCP-155B4MSRx User Manual
RoHS Compliant Small Form Factor Pluggable Transceiver for Fast
Ethernet, ATM, SONET OC-3/SDH STM-1
FEATURES
Description
The LCP-155B4MSRx series are a hot
pluggable 3.3V Small-Form-Factor transceiver
module designed expressly for high-speed
communication applications that require rates of
up to 155Mbit/sec. It is compliant with the ATM,
SONET OC-3/SDH STM-1 standards, as well as
the SFP Multisource Agreement (MSA).
The LCP-155B4MSRx transceivers provide with
the LC receptacle that is compatible with the
industry standard LC connector. The transceiver
is also compatible with industry standard RFT
connector and cage.
The post-amplifier of the LCP-155B4MSRx also
include a LOS (Loss Of Signal) circuit that
provides a TTL logic-high output when an
unusable optical signal level is detected.
The LCP-155B4MSRx transceivers are a Class
1 eye safety product. The optical power levels,
under normal operation, are at eye safe level.
Compliant with SFP Transceiver MSA
specification
LC-155B4MSRx long-haul SONET OC-3 / SDH
STM-1 (L-1.1) Compliant
Compliant with Industry Standard RFT
Electrical Connector and Cage
Single + 3.3V Power Supply and TTL Logic
Interface
EEPROM with Serial ID Functionality
Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Duplex LC Connector interface
Applications
SONET OC-3/SDH STM-1
ATM Network
Fast Ethernet
Switch to Switch interface
Switched backplane applications
File server interface
Performance
LCP-155B4MSRx Data Link up to 40km in
9/125um Signal Mode Fiber
DELTA ELECTRONICS, INC.
1 Jan. 2008
Rev. 0B
www.deltaww.com
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Supply Voltage VCC 0 5 V
Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
See order
Case Operating Temperature TC -5 +70 ºC
information
for detail
Supply Voltage VCC 3.135 3.465 V
Electrical Characteristics
(VCC=3.135V to 3.465V)
Parameter Symbol Min. Typ. Max. Unit Note
Total Supply Current ICCT 200 300 mA
Transmitter
Transmitter Differential Input Voltage VDT 0.5 2.4 V 1
Transmitter Disable Input-High V
Transmitter Disable Input-Low V
Transmitter Fault Pull up Resistor R
Transmitter Fault Output-High V
Transmitter Fault Output-Low V
DISH
DISL
TX_FAULT
TXFH
TXFL
Receiver
Receiver Differential Output Voltage VDR 0.35 1 2 V 3
Receiver LOS Load R
LOS Output Voltage-High V
LOS Output Voltage-Low V
Output Data Rise/Fall Time tr/ t
RXLOS
LOSH
LOSL
f
Notes:
1. Internally AC coupled and terminated to 100 Ohm differential load.
2 VCC+0.3 V
0 0.8 V
4.7 10 k 2
2 VCC+0.3 V
0 0.8 V
4.7 10 k 2
2 VCC+0.3 V
0 0.8 V
2.5 nsec 4
2. Pull up to V
on host Board.
CC
3. Internally AC coupled, but requires a 100 Ohm differential termination at or internal to Serializer/
Deserializer.
4. These are 20%~80% values.
2 Jan. 2008
Rev. 0B
DELTA ELECTRONICS, INC.
www.deltaww.com
Optical Characteristics
(VCC=3.135V to 3.465V, Data Rate=155Mb/sec, PRBS=223-1 NRZ, 9/125µm SMF)
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Output Optical Power (Avg.) P
O
-5 0
Optical Extinction Ratio ER 10 dB
Center Wavelength
Spectral Width (RMS)
Optical Rise/Fall Time
Output Eye
λ
t
C
σ
r/tf
1263 1310 1360 nm
3
2 ns 1
Compliant with Bellcore TR-NWT-000253 and ITU recommendation
G.957
Receiver
Sensitivity (Avg.) P
Input Optical Wavelength
IN
λ
LOS-Deasserted (Avg.) P
LOS-Asserted (Avg.) P
D
LOS-Hysteresis PA-P
Overload P
O
A
D
-34
1200 1310 1600 nm
-34
-48 dBm
0.5 dB
-3 dBm
Notes:
1. These are unfiltered 10%~90% values.
2. The sensitivity is provided at a BER of 1×10
23
2
-1 PRBS and ER=9dB.
-10
or better with an input signal consisting of 155Mb/s,
dBm
nm
dBm 2
dBm
Mask of the eye diagram for the optical transmit signal
DELTA ELECTRONICS, INC.
3 Jan. 2008
Rev. 0B
www.deltaww.com
SFP Transceiver Electrical Pad Layout
Pin Function Definitions
Pin Num. Name Function Plug Seq. Notes
1 VeeT Transmitter Ground 1
2 TX Fault Transmitter Fault Indication 3 Note 1
3 TX Disable Transmitter Disable 3
4 MOD-DEF2 Module Definition 2 3 Note 3, 2 wire serial ID interface
5 MOD-DEF1 Module Definition 1 3 Note 3, 2 wire serial ID interface
6 MOD-DEF0 Module Definition 0 3 Note 3, Grounded in Module
7 Rate Select Not Connect 3 Function not available
8 LOS Loss of Signal 3 Note 4
9 VeeR Receiver Ground 1 Note 5
10 VeeR Receiver Ground 1 Note 5
11 VeeR Receiver Ground 1 Note 5
12 RD- Inv. Received Data Out 3 Note 6
13 RD+ Received Data Out 3 Note 7
14 VeeR Receiver Ground 1 Note 5
15 VccR Receiver Power 2 3.3 ± 5%, Note 7
16 VccT Transmitter Power 2 3.3 ± 5%, Note 7
17 VeeT Transmitter Ground 1 Note 5
18 TD+ Transmit Data In 3 Note 8
19 TD- Inv. Transmit Data In 3 Note 8
20 VeeT Transmitter Ground 1 Note 5
Plug Seq.: Pin engagement sequence during hot plugging.
Note 2
Module disables on high or open
DELTA ELECTRONICS, INC.
4 Jan. 2008
Rev. 0B
www.deltaww.com
Loading...