155Mbps, SFF LC Duplex Optical Transceiver Module for
Fast Ethernet, ATM, SONET/OC-3, SDH/STM-1
Features:
Full Compliance with the Optical Performance
Requirements of the ATM 100Mbps and 100
Base-FX Version of IEEE 802.3u.
Multi-Source 2×5 package styles with LC
Receptacle.
Single 3.3V Power Supply.
PECL Differential Inputs and Outputs.
PECL (LC-155B2xxxxxx Series) or TTL
(LC-155B4xxxxxx Series) Receiver Signal
Detect Indicator.
RoHS Compliance
Wave Solder and Aqueous Wash Process
Compatible.
Description:
The LC-155Bxxxxxxx series are SFF (Small Form
Factor) optical transceiver modules designed
expressly for high-speed communication applications
that require rates of up to 155Mbps. They are all
compliant with the SONET/SDH standards.
The LC-155Bxxxxxxx transceivers are supplied in 2
×5 DIP package style with duplex LC connector and
are fully compliant with SFF Multi-Source Agreement
(MSA).
The LC-155Bxxxxxxx transceivers can meet Class-1
eye safety standard and effective distance depending
on ITU-T G.957 standard or power penalty.
The transmitter sections utilize 1310nm Edge Emitting
InGaAsP Laser Diode. This Laser Diode is packaged
in the optical subassembly portion of the transmitter
section. A custom silicon IC that converts differential
PECL logical signals into an analog LD driving current
drives it.
The receiver sections utilize InGaAs PIN photodiodes
coupled into a custom silicon trans-impedance
preamplifier IC. These are packaged in the optical
subassembly portion of receiver.
These PIN / Preamplifier combinations are coupled
into a custom quantizer IC which provides the final
pulse shaping for the logic output and the Signal
Detect function. The data output is differential. The
signal detect output is single-ended.
Application:
Single-mode Fiber Backbone Links.
Fast Ethernet and ATM Compatible.
Single-mode Fiber Media Converter.
DELTA ELECTRONICS, INC.
http://www.deltaww.com
1
Jan., 2008
Rev.:0H
LC-155Bxxxxxxx
Absolute Maximum Ratings
Parameter
Storage Temperature Ts -40 85 ºC
Lead Soldering Temperature T
Lead Soldering Time t
Supply Volt age VCC 0 5 V
SymbolMin. Typ. Max. Unit Note
260 ºC
SOLD
10 Sec.
SOLD
Recommended Operating Conditions
Parameter SymbolMin. Typ. Max. Unit Note
Data Rate 100 155.52200 Mbps
Ambient Operating Temperature TA0 70 ºC 1
Supply Volt age VCC 3.15 3.3 3.45 V
Note: See “Order Information” for detail
Electrical Characteristics
Parameter SymbolMin. Typ. Max. Unit Note
Transmitter
Transmitter Data Input Voltage-Low VIL-VCC-1.81 -1.48 V
Transmitter Data Input Voltage-High VIH-VCC-1.16 -0.88 V
Transmitter Disable Input-Low V
Transmitter Disable Input High V
Receiver
Data Output Voltage-Low VOL-VCC-1.95 -1.62 V
Data Output Voltage-High VOH-VCC-1.045 -0.74 V
SD Output Voltage-Low V
SD Output Voltage-High V
SD Output Voltage-Low V
SD Output Voltage-High V
Supply Current Icc
Mean Launch Power Po
Optical Extinction Ratio E.R.
Center Wavelength
Spectral Width (RMS)
λ
σ
C
150
-15 -8
-5 0
9
1280 1310 1340 nm
7.7
3
Output Eye Diagram Compliant with ITU-T recommendation G. 957
Receiver
Supply Current Icc
Sensitivity PIN
Overload P
SAT
Signal Detect-Asserted PA
150
-31
-34
-8
-10
-31
-34
Signal Detect-DeAsserted PD -45 dBm
Signal Detect-Hysteresis PA-PD 0.5 dB
Note: The sensitivity should be tested at a BER of 1×10
NRZ, 2
23
-1 PRBS and E.R.=9dB.
-10
or better with an input signal consisting of 155Mbps,
mA
dBm
LC-155BxMxxxxx
dB
nm
LC-155BxMxxxxx
mA
dBm
LC-155BxMxxxxx
dBm
LC-155BxMxxxxx
dBm
LC-155BxMxxxxx
DELTA ELECTRONICS, INC.
http://www.deltaww.com
2
Jan., 2008
Rev.:0H
Pin Definition
Mask of the eye diagram for the optical transmit signal
LC-155Bxxxxxxx
PIN Symbol
1 GND Receiver Signal Ground
2 VccR Receiver Power Supply
3 SD Receiver Signal Detect (LVPECL or LVTTL)
4 RD(-) Receiver Data Out Inverted (LVPECL)
5 RD(+) Receiver Data Out Non-inverted (LVPECL)
6 VccT Transmitter Power Supply
7 GND Transmitter Signal Ground
8 TxDis Transmitter Disable
9 TD (+) Transmitter Data In Non-inverted (LVPECL)