Delta Electronics GEN User Manual

SERIES

SNAP-IN MOUNTING HIGH PERFORMANCE IEC CONNECTOR FILTERS

DVE

INTRODUCTIONS

1. Snap-in mounting type to reduce labor cost. Compact and reliable at low cost.

2. Bleeder resistor can be added with suffix "-R" on part numbers,except G3H,G3V,W3V,G3J,W3J,types.

3. Optional side snap-in mounting clip type with suffix (H) on part numbers. 4

. All part numbers are UL recongnized, CSA certified and VDE

approved.

5. With optional Y-Cap from 100pF to 3300pF.

6. Safety under apply for 03/06/10GENG3U(H) series.

COMPONENTSCOMPONENTS

PART NO. Cx (uF) L (mH) Cy (pF) R ( )

01GENG3E/W3E/-R 6.5 03GENG3E/W3E/G3U(H)/-R 2.5 03GENW3ES/-R 2.5 03GENG3Q/W3Q/-R 4 06GENG3E/W3E/G3U(H)/-R 0.8 06GENG3Q/W3Q/-R 1.5 06GENW3ES/-R 0.8 10GENG3E/W3E/G3U(H)/-R 0.2 10GENG3C/W3C/-R 0.4 10GENG3Q/W3Q/-R 0.3

10GENW3ES/-R 0.2 15GENG3E/W3E/-R 0.2 20GENG3E/W3E/-R 0.3

***** *****

UL, CSA approved to 4A 115/250V UL, CSA approved to 8A 115/250V VDE approved to 8A/250V

0.1 2200 1M

UL, CSA approved to 13A 115/250V

VDE approved to 10A/250V

VDE approved to 16A/250V

***

SPECIFICATIONS

1. Maximum leakage current each line-to-ground @ 115VAC 60Hz: 0.2mA @ 250VAC 50Hz: 0.4mA

2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC

3. Operating frequency: 50/60Hz

4. Rated voltage: 115/250VAC

INSERTION LOSS (TYPICAL)

03GENG3E 06GENG3E

80 dB

60 dB

40 dB

20 dB

0 dB

10K

COMMON MODE COMMON MODE

100K

IEC INLET FILTERS

DIFF. MODE DIFF. MODE

10M

MINIMUM INSERTION LOSS IN dB

CURRENT FREQUENCY-MHz RATING .15 .50 1.0 5.0 10 30

6A (G3Q) 15 20 24 35 40 55

10A (G3C) 10 15 15 25 30 35 10A (G3Q) 10 12 15 30 32 45

COMMON MODE (L-G) IN 50 OHM SYSTEM

1A 28 35 38 38 40 40 3A 20 25 30 38 40 40 6A 12 18 24 35 40 40

10A 4 10 13 28 35 40

15A 4 10 13 28 35 40 20A 8 10 15 25 30 35

ELECTRICAL SCHEMATIC

N E

R: 1M /-R ONLY

L O A D

20GENG3E

80 dB

60 dB

40 dB

20 dB

0 dB

10K

COMMON MODE

100K

DIFF.MODE

10M

2-7

PANEL

PCB

Suggested thickness of mounting panel is from

0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout

ASSEMBLY FROM FRONT

MECHANICAL CONSTRUCTION

NG3E, NG3C, NG3Q (Optional wire type)

IEC INLET FILTERS

NG3E(H), NG3C(H), NG3Q(H) (Optional wire type)

1.22 0.02

31.0 0.5

24.0 0.5

0.945 0.02

1.12 MAX.

28.4 MAX.

1.22 0.02

31.0 0.5

24.0 0.5

0.945 0.02

1.12 MAX.

28.4 MAX.

+0.04

+1.0

3.6 0.5

0.142 0.02

1.66MAX.

42.16MAX.

2.1MAX.

53.4MAX.

1.12 0

28.45 0

+0.012

+0.3

SUGGESTED MOUNTING CUTOUT

GENG3E

+0.04

+1.0

3.6 0.5

0.142 0.02

R0.08MAX(2X)

R2.0MAX

1.66MAX.

42.16MAX.

2.1MAX.

53.4MAX.

1.16 0.004

29.5 0.1

SUGGESTED MOUNTING CUTOUT

0.862 0.004

R0.08MAX.

R2.0MAX.

0.0315~0.06

0.8~1.6

0.85 0.004

0.0315~0.063

21.9 0.1

21.5 0.1

0.8~1.6

21.4MAX.

0.84MAX.

21.4MAX.

0.84MAX.

GENG3E(H)

1.22 0.02

31.0 0.5

1.12 0.02

28.4 0.5

0.94 0.02

24.0 0.5

2.8

0.11

+1.0

0.5

+0.04

0.02

R0.08MAX.

R2.0MAX.

38.0 0.5

1.50 0.02

1.94 0.04

49.4 1.0

1.16 0.004

29.5 0.1

20.4 0.5

0.80 0.02

0.8~1.6

0.85 0.004

21.9 0.1

NG3U(H) (With Compact Size)

NW3ES

20GENG3E (Optional wire type)

2-8

NG3U(H)

24.0 0.5

0.945 0.02

1.22 0.2

31.0 0.5

-0.02

+0.04

-0.5

+1.0

3.6

0.142

1.12 MAX.

28.4 MAX.

BROWN

0.248X0.031

6.3X0.8

40.0 MAX.

1.575 MAX.

BLUE

G/Y

2.60MAX.

66.0MAX.

1.36MAX.

34.5MAX.

3.19MAX.

81.0MAX.

1.04MAX.

26.5MAX.

ALL WIRE LEADS 4.0" LONG MIN.

0.84MAX.

21.3MAX.

+0.012

1.12 0 +0.3

28.45 0

SUGGESTED MOUNTING CUTOUT

NW3ES

0.138

3.5

SUGGESTED MOUNTING CUTOUT

(MOUNTING FROM REVERSE)

1.496MAX.

R0.08MAX.

R2.0MAX.

38.0MAX.

R0.118MAX.

R4.0MAX.

21.9 0.1

0.862 0.004

0.0315~0.06

0.8~1.6

1.18

30.0

+0.02

+0.5

1.043-0

26.5-0

+0.02

1.417-0 +0.5

36.0-0

INCH

UNIT: