Delta Electronics AE57BSTD, AE57GSTD, AS38BSTD, AS57BSTD Quick Start Manual

English-1

Preface

Thank you for purchasing DELTA’s DOP-A, AE and AS series. This quick start will be helpful in the installation,
wiring and inspection of Delta HMI. Before using the product, please read this quick start to ensure correct use.
You should thoroughly understand all safety precautions before proceeding with the installation, wiring and
operation. Place this quick start in a safe location for future reference. Please observe the following
precautions:

 Install the product in a clean and dry location free from corrosive and inflammable gases or liquids.
 Ensure that all wiring instructions and recommendations are followed.
 Ensure that HMI is correctly connected to a ground. The grounding method must comply with the

electrical standard of the country.

 Do not modify or remove wiring when power is applied to HMI.
 Do not touch the power supply during operation. Otherwise, it may cause electric shock.
 For the information of HMI software operation, software installation and hardware wiring, please

refer to the HMI software manual.

If you have any questions during operation, please contact our local distributors or Delta sales representative.

The content of this quick start may be revised without prior notice. Please consult our distributors or download
the most updated version at http://www.delta.com.tw/industrialautomation

.

Safety Precautions

Carefully note and observe the following safety precautions when receiving, inspecting, installing, operating,
maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are used to mark
safety precautions when using the Delta’s HMI product. Failure to observe these precautions may void the
warranty!

Installation

¾ Comply with quick start for installation. Otherwise it may cause equipment damage.
¾ Do not install the product in a location that is outside the stated specification for the HMI. Failure to

observe this caution may result in electric shock, fire, or personal injury.

Wiring

¾ Connect the ground terminals to a class-3 ground (Ground resistance should not exceed 100Ω).

Improper grounding may result in communication error, electric shock or fire.

Operation

¾ The users should use Delta Screen Editor software to perform editing in Delta's HMI product. To

perform editing and confirming HMI programs without using Delta Screen Editor software in Delta's
HMI product may result in abnormal operation.

¾ Do not modify wiring during operation. Otherwise it may result in electric shock or personal injury.
¾ Never use a hard or pointed object to hit or strike the screen as doing this may damage the screen

and let the screen has not respond at all, and then cause HMI to work abnormally..

English-2

Maintenance and Inspection

¾ Do not touch any internal or exposed parts of the HMI as electrical shock may result.
¾ Do not remove operation panel while power is on. Otherwise electrical shock may result.
¾ Wait at least 10 minutes after power has been removed before touching any HMI terminals or

performing any wiring and/or inspection as an electrical charge may still remain in the HMI with
hazardous voltages even after power has been removed.

¾ Turn the power off before changing backup battery and check system settings after finishing change.

(all data will be cleared after changing battery).

¾ Be sure the ventilation holes are not obstructed during operation. Otherwise malfunction may result

due to bad ventilation or overheating troubles.

Wiring Method

¾ Remove the terminal block from the HMI before wiring.
¾ Insert only one wire into one terminal on the terminal block.
¾ If the wiring is in error, perform the wiring again with proper tools. Never use force to remove the

terminals or wires. Otherwise, it may result in malfunction or damage.

¾ For the power line that forced to take out, ensure to check wiring again and restart.

Communication Wiring

¾ Comply with communication wiring specification for wiring.
¾ Wiring length should comply with the stated specification for the HMI.
¾ Proper grounding to avoid bad communication quality.

Installation and Storage Conditions

The product should be kept in the shipping carton before installation. In order to retain the warranty coverage,
the HMI should be stored properly when it is not to be used for an extended period of time. Some storage
suggestions are:

 Store in a clean and dry location free from direct sunlight.
 Store within an ambient temperature range of -20°C to +60°C (-4°F to 140°F).

 Store within a relative humidity range of 10% to 90% and non-condensing.
 Do not store the HMI in a place subjected to corrosive gases and liquids.
 Correctly packaged and placed on a solid and durable surface.
 Do not mount the HMI adjacent to heat-radiating elements or in direct sunlight.
 Do not mount the HMI in a location subjected to corrosive gases, liquids, or airborne dust or metallic

particles.

 Do not mount the HMI in a location where temperatures and humidity will exceed specification.
 Do not mount the HMI in a location where vibration and shock will exceed specification.
 Do not mount the HMI in a location where it will be subjected to high levels of electromagnetic

radiation.

Installation

Installation Note:

 Improper installation will result in malfunction and greatly reduce the life of the HMI. Be sure to

follow the guidelines in this quick start when installing the HMI.

 In order to ensure the HMI being well ventilated, make sure that the ventilation holes are not

obstructed and must provide sufficient free space around HMI.

 For use on a flat surface of a Type 4X "Indoor Use Only" enclosure or equivalent.

English-3

Installation Method:

Step 1: Ensure to put waterproof gasket into HMI
and then insert the HMI into the panel cutout.

Step 2: Ensure to insert fasteners into the HMI’s
insertion slots and turn the screw till screws touch panel
cutout.

Step 3: Turn the screw with less than torque 0.7N.M to avoid damage to plastic box.

Torque: 6.17lb-inch(0.7N-M)

Power Line Installation

Recommended wiring is in the table below:

Type Wire Gauge (AWG) Stripped length Torque

Solid 28~12 7~8 mm 4.5 lb-in

Stranded 28~12 7~8 mm 4.5 lb-in

Be sure to plug power line into HMI according to following arrow direction.

DOP-AS38BSTD(-W) DOP-A(E)57G(B)(C)STD(-W)

English-4

Basic Inspection

Item Content

General Inspection

 Periodically inspect the screws of the connection between the HMI and device.

Tighten screws as necessary as they may loosen due to vibration and varying
temperatures.

 Ensure that oil, water, metallic particles or any foreign objects do not fall inside the

HMI, control panel or ventilation slots and holes. As these will cause damage.

 Ensure the correct installation and the control panel. It should be free from

airborne dust, harmful gases or liquids.

Inspection before

operation (power is

not applied)

 Ensure that all wiring terminals are correctly insulated.
 Ensure that all wiring is correct or damage and or malfunction may result.
 Visually check to ensure that there are not any unused screws, metal strips, any

conductive or inflammable materials inside HMI.

 Ensure to lower electromagnetic interference when devices are influenced by it.
 Ensure that the external applied voltage to HMI is correct and matched to the

controller.

Inspection before

operation (power is

applied)

 Check if power LED lights.
 Check if the communication among devices is normal.
 Please contact your local Delta sales representative if there are any abnormal

conditions.

Pin Definition of Serial Communication

COM1 Port [A, AE and AS57BSTD Series]

Contact

COM Port PIN

RS-232
1
2 RXD
3 TXD
4
5 GND
6
7 RTS
8 CTS
9

Note: Blank = No Connection.

DOP-A80THTD1
DOP-AE80THTD
DOP-AE94BSTD
DOP-A(E)10THTD1

DOP-AS57BSTD

Pin

English-5

COM2 Port [A Series]

MODE1 MODE2 MODE3

COM Port PIN

RS-232 RS-422 RS-485
1 RXD- D­2 RXD RXD+ D+
3 TXD TXD+ D+
4 TXD- D­5 GND
6 RTS-
7 RTS RTS+
8 CTS CTS+
9 CTS-

Note 1: Blank = No Connection.
Note 2: When selecting Mode3 (for RS-485), D+ indicates that PIN 2 and PIN 3 is connected, and D-

indicates that PIN 1 and PIN 4 is connected.

COM2 and COM3 Port [AE, A80THTD1 and A10THTD1 Series]

MODE1 MODE2 MODE3 MODE4 MODE5 MODE6

COM Port PIN

RS-232 RS-422 RS-485 RS-232*2 RS-422*2 RS-485*2
1 RXD- D- RXD1- D1­2 RXD RXD+ D+ RXD1 RXD1+ D1+
3 TXD TXD+ D+ TXD1 TXD1+ D1+

COM2

4 TXD- D- TXD1- D1-

5 GND

6 RTS- TXD2- D2­7 RTS RTS+ TXD2 TXD2+ D2+
8 CTS CTS+ RXD2 RXD2+ D2+

COM3

9 CTS- RXD2- D2-

Note 1: Blank = No Connection.
Note 2: When selecting Mode3 (for RS-485), D+ indicates that PIN 2 and PIN 3 is connected, and D-

indicates that PIN 1 and PIN 4 is connected. When selecting Mode6 (for RS-485), D1+
indicates that PIN 2 and PIN 3 is connected, D1- indicates that PIN 1 and PIN 4 is connected,
D2+ indicates that PIN 7 and PIN 8 is connected, and D2- indicates that PIN 6 and PIN 9 is
connected.

COM1 and COM3 [AS38BSTD Series]

MODE1 MODE2

COM Port PIN

RS-232 RS-232*2
1
2 RXD RXD1
3 TXD TXD1

COM1

4

5 GND

6
7 RTS TXD2
8 CTS RXD2

COM3

9

Note: Blank = No Connection.

Pin

Pin

Pin

English-6

COM2 Port [AS38BSTD Series]

MODE1 MODE2

COM Port PIN

RS-422 RS-485

R- RXD- D-

R+ RXD+ D+

T- TXD- D-

T+ TXD+ D+

G GND

Note 1: When selecting Mode2 (for RS-485), D+ indicates that R+ and T+ is connected, and D-

indicates that R- and T- is connected.

COM2 and COM3 Port [AS57BSTD Series]

MODE1 MODE2

COM Port PIN

RS-422 RS-485

R- RXD- D-

R+ RXD+ D+

T- TXD-

T+ TXD+

G

GND

(for COM2 and COM3 both)

Note: Blank = No Connection.

Dimensions

DOP-AS38BSTD(-W)

118.8

+0.04+1

(4.68 )

140.8

104.8

0

0

(3.65 )

T=1.6mm(0.06in) ~

92.8

0

+1

3.0mm(0.12in)

NOTE:

0

+0.04

T

4-R3

36.7

R-

COM3

COM2

Units:mm

English-7

DOP-AS57BSTD

0.12in(3.0mm)

T=0.06in(1.6mm) ~

(5.21 )

+1

0

+0.04

0

(6.79 )

0

+1 +0.04

0

144.1(5.67)

184.1(7.25)

6.1(0.24)39.0(1.54)

172.4

132.4

4-R3(0.12)

T

NOTE:

DOP-A(E)57G(B)(C)STD(-W)

3.0mm(0.12in)

T=1.6mm(0.06in) ~

(5.21 )

+1

0

+0.04

0

(6.79 )

0

+1 +0.04

0

144.1(5.67)

184.1(7.25)

6.1(0.24)39.0(1.54)

172.4

132.4

4-R3(0.12)

T

NOTE:

DOP-A80THTD1 / DOP-AE80THTD

T=1.6mm(0.06in) ~

3.0mm(0.12in)

(1.75)

178.1(7.01)

243.1(9.57)

0

+1

231.4

0

(9.11 )

+0.04

+0.04

(6.55 )

0

+1

166.4

0

NOTE:

4

-

R

3

.

0

(

0

.

1

2

)

44.4

T

6.1(0.24)

Units:mm

Units:mm

Units:mm

English-8

DOP-AE94BSTD

(8.27 )

210.2

0

+1

+0.04

0

285.2

0

+1

(11.22 )

+0.04

0

4

-

R

3

.

0

NOTE:

T=1.6mm(0.06in) ~

3.0mm(0.12in)

T

DOP-A(E)10THTD1

3.0mm(0.12in)

+0.04

(11.22 )

+1

0

0

T=1.6mm(0.06in) ~

(8.27 )

+1

0

+0.04

0

210.2

285.2

4

-

R

3

.

0

(

0

.

1

2

)

NOTE:

T

297.1(11.70)

222.1(8.74)

43.1(1.70) 6.1(0.24)

Units:mm

Units:mm

English-9

Specifications

MODEL AS38BSTD(-W) AS57BSTD A(E)57BSTD(-W) A(E)57GSTD(-W)

Display Type

3.8” STN LCD

(8 shades of blue)

5.7” STN LCD

(8 shades of blue)

5.7” STN LCD

(8 shades of blue)

5.7” FSTN LCD

(16 shades of gray)

Resolution 320 x 240 pixels

Back Light

LED Back Light

(about 10 thousand

hours at 25oC)

CCFL Back Light (about 50 thousand hours at 25oC)

LCD MODULE

Display Size

3.8”

(76.8 x 57.6mm)

5.7” (115.17 x 86.37mm)

Operation System

Windows Base Real Time OS

MCU

32-bit RISC Micro-controller

NOR Flash ROM

NOR Flash ROM 2 Mbytes

(System: 1MB / User: 1MB）

NOR Flash ROM 4 Mbytes

(System: 1MB / User: 3MB)

SDRAM

4 Mbytes 16Mbytes

Backup Memory

(Bytes)

128K

A: 256K

AE: 512K

SM Card

3 3

EXT.

Memory

USB Host

(Ver 1.1)

3 3

Extension Interface

3 (AE) 3 (AE)

USB for Download

[USB Client]

1 USB Client Ver 1.1

USB for Data

Storage / Printer

[USB Host]

3 3

COM1

RS-232

COM2

RS-422 / RS-485 RS-232 / RS-422 / RS-485

Serial

COM

Port

COM3

RS-232 RS-422 / RS-485 RS-232 / RS-422 / RS-485 (AE)

Function Key User defined key x 4 + System key x 1

Operation Voltage

DC +24V (-10% ~ +15%) (Please use isolated power supply)

(Note 2)

Backup Battery

3V lithium battery CR2032 x 1 / battery life: 5 years

Buzzer 85dB

Perpetual Calendar

(RTC)

Built-in

Cooling Method Natural air circulation

Safety Approval

(Waterproof for

front panel)

IP65 / NEMA4 / CE, UL

(Note 1)

Operation Temp.

0°C ~ 50°C

Storage Temp.

-20°C ~ +60°C

English-10

MODEL AS38BSTD(-W) AS57BSTD A(E)57BSTD(-W) A(E)57GSTD(-W)

Ambient Humidity

10% ~ 90% RH [0 ~ 40°C], 10% ~ 55% RH [41 ~ 50°C]

Pollution Degree 2

Vibration

Resistance

IEC 61131-2 Compliant

5Hz≦f＜9Hz = Continuous: 1.75mm / Occasional: 3.5mm

9Hz≦f≦150Hz = Continuous: 0.5g / Occasional: 1.0g

X, Y, Z directions for 10 times

Dimensions

(W) x (H) x (D) mm

140.8 x 104.8 x

44.8

184.1 x 144.1 x 47

Panel Cutout
(W) x (H) mm

118.8 x 92.8 172.4 x 132.4

Weight Approx. 310g Approx. 760g

NOTE

1) DOP-AE94BSTD this model is not UL recognized.

2) Users please use isolated power supply except DOP-A80THTD1, DOP-AE80THTD, DOP-AE94BSTD, and

DOP-A(E)10THTD1 these models.

3) Users can download the Screen Editor, the program editor of Delta HMI product and the user manual via the

following link: http://www.delta.com.tw/industrialautomation/.

4) The content of this quick start may be revised without prior notice. Please consult our distributors or download the

most updated version at http://www.delta.com.tw/industrialautomation/.

English-11

MODEL A(E)57CSTD(-W)

A80THTD1
AE80THTD

AE94BSTD A(E)10THTD1

Display Type

5.7” STN LCD
(256 colors)

8” TFT LCD

(65536 colors)

9.4” STN LCD

(8 shades of blue)

10.4” TFT LCD
(65536 colors)

Resolution 320 x 240 pixels 640 x 480 pixels

Back Light

CCFL Back Light

(about 50 thousand

hours at 25oC)

CCFL Back Light

(about 50 thousand

hours at 25oC)

CCFL Back Light

(about 30 thousand

hours at 25oC

CCFL Back Light

(about 30 thousand

hours at 25oC

LCD MODULE

Display Size

5.7” (115.17 x

86.37mm)

8” (162.2 x

121.7mm)

9.4” (192.0 x

144.0mm)

10.4” (211.2 x

158.4mm)

Operation System

Windows Base Real Time OS

MCU

32-bit RISC Micro-controller

NOR Flash ROM

NOR Flash ROM 4

Mbytes (System:

1MB / User: 3MB)

NOR Flash ROM 8 Mbytes (System: 1MB / User: 7MB)

SDRAM

16 Mbytes 32 Mbytes 16Mbytes 32 Mbytes

Backup Memory

(Bytes)

A: 256K

AE: 512K

512K 512K 512K

SM Card

3

3 (AE)

EXT.

Memory

USB Host

(Ver 1.1)

3 3 3

Extension Interface

3 (AE)

3 (AE)

3

3 (AE)

USB for Download

[USB Client]

1 USB Client Ver 1.1

USB for Data

Storage / Printer

[USB Host]

3 3 3

COM1

RS-232

COM2

RS-232 / RS-422 / RS-485

Serial

COM

Port

COM3

RS-232 / RS-422 /

RS-485 (AE)

RS-232 / RS-422 / RS-485

Function Key

User defined key x

4 + System key x 1

User defined key x
6 + System key x 1

User defined key x

11 + System key x

1

User defined key x

7 + System key x 1

Operation Voltage

DC +24V (-10% ~ +15%) (Please use isolated power supply)

(Note 2)

Backup Battery

3V lithium battery CR2032 x 1 / battery life: 5 years

Buzzer 85dB

Perpetual Calendar

(RTC)

Built-in

Cooling Method Natural air circulation

Safety Approval

(Waterproof for

front panel)

IP65 / NEMA4 / CE, UL

(Note 1)

Operation Temp.

0°C ~ 50°C