Delta Children Jeep SPORT UTILITY Instruction Manual

SPORT UTILITY

ALL-TERRAIN
STROLLER

INSTRUCTION MANUAL

ADULT ASSEMBLY REQUIRED
STYLES AND COLORS MAY VARY

12498

Fits Graco® SnugRide® Click Connect™ 30, 35, and 40 Infant Car Seat (not included)

Fits Evenflo® Embrace™ Select Infant Car Seat (not included)

Fits Evenflo® Nurture™ Infant Car Seat (not included)

Fits Chicco® Keyfit 30™ Infant Car Seat (not included)

Fits Britax® B-Safe 35™ Infant Car Seat (not included)

WARNING:

CHOKING HAZARD

Adult assembly required because of
small parts. Keep assembly parts out
of reach of children

This stroller is not from, sponsored or endorsed by Graco Children’s Products Inc.
This stroller is not from, sponsored or endorsed by Evenflo Company, Inc.
This stroller is not from, sponsored or endorsed by Artsana S.p.A.
This stroller is not from, sponsored or endorsed by Britax®.

Customer Care Tel. [phone]

under 3 years.

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

www.DeltaChildren.com

DCP-02052019-V3

WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these
instructions for future reference.

WARNING: Failure to follow these instructions could result in serious injury or death.
WARNING: Avoid serious injury from falling or sliding out. Always insure that the child is properly

positioned by using the safety harness according to these instructions.

WARNING: Never leave children unattended.
WARNING: CHOKING HAZARD Adult assembly required because of small parts.

Keep (assembly parts) out of reach of children under 3 years.

CAUTION: Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of
the stroller and cause hazardous unstable conditions.

• The maximum weight that can be carried in the lower basket, and child tray, each is 3 lbs (1.36 kg).
Excessive weight may cause a hazardous unstable condition to exist.

• Before allowing the children near the stroller, be certain the stroller is fully erect and latched in the
open locked position.

• Use of the stroller with children weighing more than 50 pounds or over 42 inches tall, will cause
excessive wear and stress on the stroller and may cause hazardous unstable condition to exist.

NEVER use the stroller on stairways or escalators.

• NEVER use the stroller with roller skates or in-line skates.

Never allow your stroller to be used as a toy.

To prevent injury:

Make sure all body parts are clear of the stroller when folding and unfolding.

CARE AND MAINTENANCE

• To clean the plastic parts on stroller use a mild cleaning solution with warm water on a sponge or
damp cloth. Hand wash fabric with damp cloth and air dry. Do not use bleach.

• To keep your stroller wheels from squeaking, use silicone or graphite based lubricant.

• Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace
or repair parts as needed.

• Discontinue use of stroller if it should become damaged or malfunctions.

• If you experience any difficulty with assembly, missing parts or use, please DO NOT return this item to
the store. Retail stores are unable to properly assist you. Contact our Customer Service Department
directly for assistance 1-646-435-8726.

1-646-435-8726

2

Parts Assembly

CLICK

IMPORTANT! Please remove all parts from the package and identify them

before assembly.
IMPORTANT! Before assembly and each use, inspect this product for

damaged hardware, loose joints, missing parts, or sharp edges. NEVER use
if any parts are missing or broken. Contact manufacturer for replacement
parts and instructions if needed. Never substitute parts. IMPORTANT! Adult
assembly is required.

Stroller Frame

Seat

Remove stroller from box. The front wheels, rear wheels, seat, canopy, and
child bar need to be installed prior to use.

WARNING: Care must be taken when folding and unfolding
the stroller to prevent finger entrapment.

Fig. 1

Fig. 1A

Front

Child Bar

Part # 50240

Canopy

Part # 50241

5 in 1 Car Seat

Adapter

Part # 50247

Back

Front Wheel

(Lock & Swivel) x 2

Part # 50242

Rear Wheel x 2

Part # 50243

Carry All Parent

Organizer

Fully Locked

Position Once

Both Sides Click

Fig. 1B

1

Opening Stroller

WARNING: Care must be taken when folding and unfolding the
stroller to prevent finger entrapment.

• First, release the locking latch clip which is located on the right side of
the stroller. (Fig. 1)

• Second, lift up on the stroller handle with both hands until the stroller
frame is in a fully opened and locked position. (Fig. 1A) The stroller is in
a fully locked position when both side handle latches are in a fully locked
position and clicks. (Fig. 1B) Prior to placing your child into the stroller,
test to make sure both latches are fully engaged and fully locked.

Customer Service Tel. [phone]

3

www.DeltaChildren.com

Fig. 2

Assembly

Please follow these instructions for the proper installation of your front wheel assembly.

Fig. 2A

2

Note: Before attaching front wheels, make sure the stroller is in a fully open
position.

Attaching Front Wheels

• To attach front wheels: Push each front wheel posts into the front
wheel housing until they “CLICK” into a fully locked position. (Fig. 2)

Note: Pull downward on each wheel to ensure that each wheel is securely

locked.

Rotate clockwise

to lock

Fig. 3 Fig. 3A

Rotate counter

clockwise to unlock

3

Front Swivel Wheel Lock

• To lock the front swivel wheel lock: Rotate the lever located on the
top of the front wheel housing clockwise until it “CLICKS” into a fully
locked position (Fig. 3).

• To unlock the front swivel wheel lock: Rotate the lever located on
the top of the front wheel housing counter clockwise until it “CLICKS” into
a fully locked position (Fig. 3A).

Removing Front Wheels
Note: Make sure the back brakes are fully engaged.

• To release front wheels: Press the grey button located on the back of
the wheel housing and pull downward to release. (Fig. 2A)

Customer Service Tel. [phone]

4

www.DeltaChildren.com

Attaching Rear Wheels:

Assembly

Please follow these instructions for the proper installation of your rear wheel assembly.

Fig. 4

Removing Rear Wheels:

4

CLICK

Fig. 4C

Fully Locked

Position

Fig. 4A

Fig. 4B

Fig. 5

Push downward on brake

lever to lock stroller

Fig. 5A

Attaching / Removing Rear Wheels
Attaching Rear Wheels

• To attach rear wheels: Push each rear wheel posts into the rear wheel
housing (Fig. 4) until they “CLICK” into a fully locked position (Fig. 4A).

Note: Pull outward on each wheel to ensure that each wheel is securely

locked.

• Repeat on opposite side.

Removing Rear Wheels

• To remove the rear wheels: Press the grey button located on the
back of the wheel housing (Fig. 4B) and pull wheel outward until wheel is
released (Fig. 4C)

• Repeat on opposite side.

Customer Service Tel. [phone]

Push upward on brake

lever to unlock stroller

5

WARNING: Always lock brakes when the stroller is not being
pushed so that the stroller will not roll away. Never leave stroller
unattended on a hill or incline as the stroller may slide down the hill.
WARNING: NEVER leave child unattended in stroller.

Rear Non-Swivel Wheel Brakes - One Touch Brake System

• To engage brakes: Apply light downward pressure to the linked brake
lever located on the right side of the rear wheel housing. (Fig. 5) Check to
make sure the brakes are in a fully locked position, making sure stroller will

not move when pushed.

• To release brakes: Gently lift up on the linked brake lever. (Fig. 5A)

5

www.DeltaChildren.com

Right / Left Seat

Housing

Assembly

CLICK

Rear Facing Seat -

Child Facing Parent-

Infant

Fig. 6

Front Facing Seat -

Child Facing

Away from Parent

-Toddler

Fig. 6A

6

Attaching / Removing Seat
Attaching Seat

• To attach seat to stroller: Face seat to the preferred direction. Rear
facing seat (Fig. 6) or front facing seat (Fig. 6A). Press seat into right / left
housing until it “CLICKS” into a fully locked position (Fig. 6B).

Note: Pull upward on seat to ensure that the seat is securely locked into

right / left seat housing.

Removing Seat

• To remove or reverse seat from stroller: Press the buttons located
on both sides of the stroller and lift seat upward to fully remove. (Fig. 6C)

Fully Locked

Position

Fig. 6B

Customer Service Tel. [phone]

Fig. 6C

6

www.DeltaChildren.com

Before Placing your Child in Stroller:

Securing Child

Close Canopy. Press both brake pedals down until they “click” into the locked position.

Make sure the brake pedals are pressed down completely.

Always set both brake pedals when parking the stroller.

Waist Belt

Waist Belt

Crotch Belt

1

Securing Child

• Place your child in the stroller. Position the crotch belt between your
child’s legs.

• Pull shoulder straps over child’s arm and shoulder and fasten both strap

ends to the restraint system.

• Fasten both waist belts to the buckle on each side of the crotch belt.
Make sure you hear a “click” on both sides.

• Check to be sure the restraint system is securely attached by pulling it
away from your child. The restraint system should remain attached.

5 Point Safety

Harness

TIGHTEN

Restraint System

2

• Tighten each waist belt and shoulder strap so that the restraint system is
snug against your child.

Please refer to the next section for instructions to tighten the waist belts.

Customer Service Tel. [phone]

3

To tighten the waist belts and shoulder straps:

• Feed the anchored end of a waist belt up through the buckle to form a
loop A. Pull the free end of the waist belt B.

• Repeat this procedure to tighten the other waist belt.

• Feed the top end of the shoulder strap through the plastic stay to form

a loop . Pull the bottom end down to tighten the strap .

• Repeat this procedure to tighten the other shoulder strap.

To loosen the waist belts and shoulder straps:

• Feed the free end of the waist belt up through the buckle to form a

• Repeat this procedure to loosen the other waist belt.

• Feed the bottom end of the shoulder strap through the plastic stay to form

a loop . Pull the top end up to loosen the strap .

• Repeat this procedure to loosen the other shoulder strap.

Please note: After adjusting the restraint system to fit your child, make sure
you pull on it to be sure it is securely fastened.

7

C

loop A. Enlarge the loop by pulling on the end of the loop toward the
buckle. Pull the anchored end of the waist belt to shorten the free end of
the waist belt B.

C

LOOSEN

D

D

www.DeltaChildren.com

Setup and Use

Fig. 7A

Velcro

Fig. 7

Canopy Adjustment Options:

Fig. 7D

Fig. 7F

7

Attaching Canopy and Canopy and Sun Visor Adjustment
Attaching Canopy

• To attach the canopy: Place canopy onto the top front of the stroller.
(Fig. 7) Then, slide both sides of the canopy locks into both canopy

housings (Fig. 7A) until they “CLICK” into a fully locked position (Fig.

7B). Match the velcro edges of the canopy with the seat velcro (Fig. 7C)
until the canopy is fully attached to the seat. Pull the front edge of the
canopy forward until fully opened. (Fig. 7D)

• To open the sun visor: Grab front edge of the sun visor under canopy
and pull down and rotate forward until fully extended. (Fig. 7E)

• To close canopy: Push backward on the front edge until canopy is all
the way collapsed. (Fig. 7F).

Removing Canopy

• To remove the canopy: First, unvelcro the canopy off the seat. Then, press
the canopy release buttons downward and slide both sides of the canopy
upward off the stroller frame sides to fully remove. (Fig. 7G)

Fig. 7C

Fully Locked

Position

Fig. 7B

Fig. 7E

Customer Service Tel. [phone]

Fig. 7G

8

www.DeltaChildren.com

Setup and Use

RECLINE

Fig. 8

8

Seat Back Recline Positioning

• To recline seat: Lift recline latch located on the back of the seat and
rotate seat downward to recline seat. (Fig. 8)

• To return to an upright position: Pull the recline latch and push seat
upward into its desired position until it “CLICKS” into a fully locked

position. (Fig. 8A)

Press Recline

Button On Both Sides

UPRIGHT

Fig. 8A

Rotate Handle Upward

Or Downward

Fig. 10A

2

Press Both Buttons

Inward

Fig. 10

2

1

Rotate

Up or Down

Fig. 9

9

Foot Rest Adjustment

• To adjust foot rest: Press both recline buttons located on left/right side
of foot rest. While pressing both recline buttons, rotate foot rest upward or
downward to its desired position until it “CLICKS” into a fully locked

position. (Fig. 9)

Customer Service Tel. [phone]

10

Adjustable Handle

• To adjust handle: Press both left / right buttons inward located on the
outside of both sides of the stroller frame. (Fig. 10) While pressing both
buttons rotate the handle upward or downward to its desired position.

(Fig. 10A)

• The handle will “CLICK” on both sides once it is in a fully locked position.

9

www.DeltaChildren.com

Setup and Use

CLICK

Fig. 11 Fig. 11A

Child Bar

Cover

Fig. 11B

11

Attaching / Removing Child Bar
Attaching Child Bar

• To attach child bar: Insert left / right sides of the child bar into the child
bar housing located on the left / right side of the stroller frame. (Fig. 11)

• The child bar will “CLICK” on both sides once it is in a fully locked position.
(Fig. 11A)

Note: Pull upward on the child bar to ensure it is securely locked onto the
stroller frame.

Removing Child Bar

• To remove child bar: Press both child bar buttons located on both sides
of the stroller frame and pull upward to release. (Fig. 11B)

2

Unzip

Fig. 11D

1

Unvelcro

Fig. 11C

Removing Child Bar Cover

• To remove child bar cover for cleaning: First, remove the velcro strap.

(Fig. 11C) Then unzip the cover from left to right located under the child bar.

(Fig. 11D)

Customer Service Tel. [phone]

10

www.DeltaChildren.com

Attaching Chicco Car Seats

®

Chicco Keyfit 30™

®

Lock The Rear Wheels:

Fig. 12

Attaching Car Seat Adapter:

Fig. 12D:

Front

Push downward on brake

lever to lock stroller

Insert On

Both Sides

Car Seat Adapter ­Correct Placement

Fig. 12B

Remove Seat:

Press Both Side
Buttons And Lift

To Fully Remove

Seat

Fig. 12A

Back

Car Seat Adapter Clicks And Locks

On Both Sides Of The Stroller Frame

When In A Fully Locked Position

Fig. 12C

Chicco Car Seat Side Locking Tabs

12

Attaching Chicco Car Seats - Keyfit 30™:

Lock Under This Area On The Adapter

®

Lock the rear wheels (Fig.12). Remove seat (Fig. 12A). Attach the car seat

adapter to the stroller frame (Fig. 12B) until it clicks into a fully locked
position (Fig. 12C). Place car seat into car seat adapter until it “CLICKS”
into a fully locked position. Chicco car seats “CLICK” and lock on both
sides of the adapter when in a fully locked position (Fig. 12D). Make sure
car seat is fully fastened by pulling upward.

Customer Service Tel. [phone]

Locking Tabs

Located On Both

Sides Of Car Seat

Securing Car Seat With Velcro Straps:

Securing Car Seat With Velcro Straps-

Final step to secure the footrest side of car seat onto stroller, use the straps
with velcro to secure seat onto stroller. (Fig. 12E). Check that car seat is
securely attached by pulling up on the car seat. To remove, undo latches and
unlock car seat from adapter.

Removing Car Seat - To remove, squeeze release handle at back of infant
restraint and lift upward out of adapter.

11

Car Seat In A Fully

Locked Position

Fig. 12E

Car Seat Locking

Tabs Lock On Both

Sides When In A Fully

Locked Position

www.DeltaChildren.com

Attaching Graco Car Seats

®

®

Graco SnugRide® Click Connect™ 30, 35, and 40

Lock The Rear Wheels: Remove Seat:

Fig. 13

Attaching Car Seat Adapter:

Fig. 13D:

Front

Push downward on brake

lever to lock stroller

Insert On

Both Sides

Car Seat Adapter ­Correct Placement

Fig. 13B

Press Both Side
Buttons And Lift

To Fully Remove

Seat

Fig. 13A

Back

Car Seat Adapter Clicks And Locks

On Both Sides Of The Stroller Frame

When In A Fully Locked Position

Fig. 13C

Car Seat Back Locking Tab Locks

Under The Back Of The Adapter

When In A Fully Locked Position

Locking Tabs

Located On Both Sides

Graco Car Seat Side Locking Tabs Lock

Into This Area On The Adapter

Of Car Seat

13

Attaching Graco Car Seats- SnugRide® Click Connect™ 30, 35

and 40:

Lock the rear wheels (Fig.13). Remove seat (Fig. 13A). Attach the car seat

adapter to the stroller frame (Fig. 13B) until it clicks into a fully locked position
(Fig. 13C). Place car seat into car seat adapter until it “CLICKS” into a fully
locked position. Graco car seats “CLICK” and lock on the back and both sides
of the adapter when in a fully locked position (Fig. 13D). Make sure car seat is
fully fastened by pulling upward.

Customer Service Tel. [phone]

®

Car Seat In A Fully

Locked Position

Car Seat Locking Tabs
Lock On Both Sides When
In A Fully Locked Position

Securing Car Seat With Velcro Straps:

Fig. 13E

Securing Car Seat With Velcro Straps-

Final step to secure the footrest side of car seat onto stroller, use the straps
with velcro to secure seat onto stroller. (Fig. 13E). Check that car seat is
securely attached by pulling up on the car seat. To remove, undo latches and
unlock car seat from adapter.

Removing Car Seat - To remove, squeeze release handle at back of infant
restraint and lift upward out of adapter.

12

www.DeltaChildren.com

Attaching Evenflo Car Seats

®

Evenflo Nurture™ and Embrace™

Lock The Rear Wheels: Remove Seat:

®

Fig. 14

Attaching Car Seat Adapter:

Fig. 14E

Fig. 14B

Front

Push downward on brake

lever to lock stroller

Insert On

Both Sides

Back

Car Seat Adapter -

Correct Placement

Fig. 14C

Press Both Side
Buttons And Lift

To Fully Remove

Seat

Fig. 14A

Car Seat Adapter Clicks And Locks

On Both Sides Of The Stroller Frame

When In A Fully Locked Position

Fig. 14D

Evenflo Locking Latch

Locks Under Center
Of Adapter When In A
Fully Locked Position

Evenflo Car Seat

Fully Locked Position

14

Attaching Evenflo Car Seats - Evenflo® Nurture™ and Embrace™­ Lock the rear wheels (Fig. 14). Remove seat (Fig. 14A). Press both buttons

located on the front side of the adapter and rotate into a downward position
(Fig. 14B). Attach the car seat adapter to the stroller frame (Fig. 14C) until it
clicks into a fully locked position (Fig.14D). Place car seat into car seat adapter
until it “CLICKS” into a fully locked position. Evenflo car seats “CLICK” and
lock on the back of the adapter when in a fully locked position (Fig. 14E). Make
sure car seat is fully fastened by pulling upward.

Customer Service Tel. [phone]

®

Fig. 14F

Securing Car Seat With Velcro Straps-

Final step to secure the footrest side of car seat onto stroller, use the straps
with velcro to secure seat onto stroller. (Fig. 14F). Check that car seat is
securely attached by pulling up on the car seat. To remove, undo latches and
unlock car seat from adapter.

Removing Car Seat - To remove, squeeze release handle at back of infant
restraint and lift upward out of adapter.

13

www.DeltaChildren.com

Attaching Britax Car Seats

®

®

Britax B-Safe 35™

Lock The Rear Wheels:

Attaching Car Seat Adapter:

Front

Fig. 15

Push downward on brake

lever to lock stroller

Insert On

Both Sides

Car Seat Adapter ­Correct Placement

Fig. 15B

Remove Seat:

Press Both Side
Buttons And Lift

To Fully Remove

Seat

Fig. 15A

Back

Fig. 15D:

Britax Car Seat Clicks and Locks

Into The Sides Of The Adapter

When In A Fully Locked Position

Car Seat Clicks And

Locks Into The Sides Of

The Adapter

15

Attaching Britax Car Seats - B-Safe 35™ -
Lock the rear wheels (Fig. 15). Remove seat (Fig. 15A). Attach the car seat

adapter to the stroller frame (Fig. 15B) until it clicks into a fully locked
position (Fig.15C). Place car seat into car seat adapter until it “CLICKS”
into a fully locked position. Britax car seats “CLICK” and lock on the both
sides of the adapter (Fig. 15D). Make sure car seat is fully fastened by
pulling upward.

Customer Service Tel. [phone]

®

Car Seat Adapter Clicks And Locks

On Both Sides Of The Stroller Frame

When In A Fully Locked Position

Fig. 15C

Fig. 15E:

Fig. 15E

Securing Car Seats With Velcro Straps-

Final step to secure the footrest side of car seat onto stroller, use the straps
with velcro to secure seat onto stroller. (Fig. 15E). Check that car seat is
securely attached by pulling up on the car seat. To remove, undo latches and
unlock car seat from adapter.

Removing Car Seat - To remove, squeeze release handle at back of infant
restraint and lift upward out of adapter.

14

www.DeltaChildren.com

Fold Latches

Fig.16

Setup and Use

Auto Lock

Fully Folded

Position

Fig. 16A

16

Folding the Stroller

WARNING: Care must be taken when folding and unfolding the
stroller to prevent finger entrapment.
NOTE: Stroller can be folded with seat attached, if folding with
seat attached, make sure canopy is in it’s fully closed position,
seat is in a fully upright position, and footrest is in it’s lowest
position before folding the stroller.

• Folding the Stroller with Seat Attached: Close the canopy as
described on page 8, Fig. 7F, position the seat to a an upright position as
described on page 9, Fig. 8A, and position footrest to it’s lowest position
page 9, Fig. 9. Pull the fold latches located on both sides of the stroller
frame upward and move handle downward, until the stroller is in a fully
folded position. Folding latch will automatically lock once stroller is in a
fully folded and locked position (Fig. 16A).

• Folding the Stroller without Seat Attached: Pull the fold latches
located on both sides of the stroller frame upward and move handle

downward, until the stroller is in a fully folded position. Folding latch will

automatically lock once stroller is in a fully folded and locked position
(Fig. 16A).

Customer Service Tel. [phone]

15

www.DeltaChildren.com

Flat Tire

The stroller features rear bicycle air tires which could become flat. If you have a flat tire, use a standard bicycle hand
air pump to inflate the tires. Inflate the tires 28 psi.

NOTE: The stroller air tires can be taken to a bicycle shop for flat tire repair.

Customer Service Tel. [phone]

16

www.DeltaChildren.com

646-435-8726

17