Page 1
Changing Table
Conforms to
ASTM F2388
Safety Standards
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
Need Help?
Please visit www.DeltaChildren.com/assembly-videos to
watch our easy and effective assembly videos
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
This product is not intended for institutional or commercial use.
Este producto no esta hecho para uso institucional o comercial.
When contacting Delta Consumer Care please reference the above information. Before contacting Delta
Consumer Care please ensure that the information above matches the information found on the label on
the Top Shelf, please reference the information found on the product when contacting Delta Consumer
Care.
Style #:
Lot:
Date:
___________
___________
___________
A
REV
To register your product for important safety alerts and updates to your product please visit
www.DeltaChildren.com and click on Product Registration.
MAY 26, 2015, 21690 , R4 ©2015 DELTA ENTERPRISE CORP.
Page 2
WARNING: Changing Table
WARNING
FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
Always secure the pad to the changing surface by inserting the strap through the hole in
the middle of the pad. See Instructions.
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
2
Page 3
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
C. Back Top Rail x 1
Part # 21682
D. Back Middle Rail x 1
Part # 21683
E. Front Top Rail x 1
Part # 21684
A. Left End Frame x 1
Part # 21680
B. Right End Frame X 1
Part # 21681
G. Top Shelf x 1
Part # 21686
PARTS:
H. Lower Shelf x 2
Part # 21687
HARDWARE KITS PART # 21689.
F. Lower Rail x 4
Part # 21685
J. Foam Pad x 1
Part # 13927
K. M6 x35 mm Bolt x 14
M4 Allen Wrench
Supplied
No drills necessary. Do not
use power screwdriver.
3
Page 4
Section 1: Changing Table Assembly
Step 1
Parts and tools required to complete step
D. Back Middle
Rail x 1
K. M6 x35 mm Bolt x 6
F. Lower Rail x 4
E. Front Top Rail x 1
A. Left End Frame x 1
Attach (1) Back Top Rail (Part D), (1) Front Top Rail (Part E) and (4) Lower Rails (Part F) to the
Left End Frame (Part A) with (6) M6x35mm Bolts (Part K) using the M4 Allen Wrench as shown.
BE SURE THE GROOVES FACE TO THE INSIDE.
D
E
K
M4 Allen Wrench
Supplied
K
K
A
K
F
F
K
K
4
Page 5
Section 1: Changing Table Assembly
Step 2
Parts and tools required to complete step
G. Top Shelf x 1
From Step 1
Rotate the Top Shelf Support 90 degrees.
Lay the Left End Frame on the floor, Rails up. Slide the Top Shelf (Part G) in the grooves on the Back
Middle Rail and Front Top Rail, into the groove on the Left End Frame, insert the pins on the Top Shelf
into the holes in the rails. GENTLY PULL THE RAILS APART. Slide (2) Lower Shelves (Part H) in the
grooves on the Lower Rails, into the grooves on the Left End Frame as shown.
G
G
H
H. Lower Shelf x 2
H
G
D / E
5
Page 6
Section 1: Changing Table Assembly
Step 3
Parts and tools required to complete step
From Step 2
K. M6 x35 mm Bolt x 6
M4 Allen Wrench
B. Right End Frame x 1
Attach (1) Right End Frame (Part B) to the assembly from step 2 with (6) M6x35 mm Bolts (Part K) using
the M4 Allen Wrench as shown.
K
Supplied
K
K
K
B
K
K
6
Page 7
Section 1: Changing Table Assembly
Step 4
Parts and tools required to complete step
From Step 3
K. M6 x35 mm Bolt x 2
C. Back Top Rail X 1
M4 Allen Wrench
Supplied
Insert the tenon of the Back Top Rail (Part C) into the slot on the top of the Back Middle Rail (Part D),
then insert (2) M6x35 mm Bolts (Part K), through the rear legs into the threaded inserts onto the Back
Middle Rail (Part D). Tighten with the M4 Allen Wrench.
K
C
K
D
7
Page 8
Section 1: Changing Table Assembly
Step 5
Parts and tools required to complete step
J. Foam Pad X 1
From Step 4
1. Check that the bolt securing the strap is tight using the M4 Allen Wrench.
2. Insert the strap through the hole in the Foam Pad (Part J).
3. Place Foam Pad (Part J) on Top Shelf (Part G).
M4 Allen Wrench
Supplied
J
G
J
8
Page 9
Section 1: Changing Table Assembly
Final
RESTRAINT HARNESS SYSTEM USE:
. PLACE THE INFANT ON THE CHANGING TABLE FOAM PAD.
. POSITION THE RESTRAINT HARNESS OVER THE MIDDLE OF THE INFANT’S
TORSO AND INSERT THE BUCKLED ENDS INTO EACH OTHER UNTIL THE LOCK
SHUT WITH A CLICK.
. GENTLY PULL THE LOOSE END OF THE STRAP TO LIGHTLY SNUG THE
RESTRAINT HARNESS AROUND THE INFANT.
MAINTENANCE
. CHECK FASTENERS PERIODICALLY FOR TIGHTNESS. DO NOT OVER TIGHTEN.
THIS MAY CAUSE DISTORTION OR BREAKAGE.
WARNING : FALL HAZARD
ALWAY KEEP CHILD WITHIN ARMS REACH.
TO FASTEN STRAP - PUSH BUCKLE SIDE TOGETHER
BE SURE BUCKLE IS FULLY FASTENED TO
SECURE CHILD SAFFELY
TO RELEASE PRESS BOTH TABS AND PULL APART
9
Page 10
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Warranty: This Delta product is warranted to be free from defects for a period
of 90 days from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
(212) 645-9033.
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Top Shelf.
STYLE No: 7595
A
COLOR
Lot No. : _______________________
Pack Date:_____________________
REV
FTY
Date of Purchase: _____________
(you should also keep your receipt)
Loading...