Delta Children 23012 Instruction Manual

PERFECT FIT
MULTI-USE

HIGH CHAIR

INSTRUCTION MANUAL

ADULT ASSEMBLY REQUIRED
THIS PRODUCT CONTAINS SMALL PARTS
STYLES AND COLORS MAY VARY

23012

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

Customer Service: 1-(800)-377-3777

www.DeltaChildren.com

DCPIM06072017

Child Tray

Part # 50271

Seat

Seat Pad

Part # 50277

Grey Part # 50275

Red Part # 50267

4 Bent Top Leg Seat Tube

Part # 50273

4 Feet

Push Button

Lock

6 1/4"

4 Bottom Infant / Toddler Straight

Extension Tube

Part # 50272

Customer Service Tel. [phone]

16"

4 Center High Chair Extension

Tube

Part # 50270

2

www.DeltaChildren.com

WARNING: When not buckled in seat, children can escape and fall suddenly.
WARNING: Always use with the restraint belt.
WARNING: Only use the seat on floor or level ground surface.
WARNING: Never use on raised surfaces such as tables, counters, chairs, beds, or near stairs. Even a

belted baby can cause the seat to slide or move off raised surfaces.

WARNING: Always stay with and watch your baby during use.
WARNING: Never use the floor seat in or near water to avoid drowning.
WARNING: Until child is able to get in and out of the booster seat without help (about 2 1/2 years old), the

child should be secured in the booster seat at all times by the restraining system. The tray is not designed
to hold the child in the chair.

FLOOR SEAT ASSEMBLY

NOTE: SEAT COVER IS REVERSIBLE

1. Place floor seat on a level floor only never on a
raised surface (Fig. 1).

2. Place child into floor seat and securely fasten
into seat with harness. To tighten harness
position the crotch belt between your child’s
legs. Fasten both waist belts to the buckle on
each side of the crotch belt. Make sure you
hear a “click” on both sides. Check to be sure
the restraint system is securely attached by
pulling it away from your child. The restraint
system should remain attached (Fig 2).

Fig. 1

Waist BeltWaist Belt

Crotch Belt

Fig. 2

Customer Service Tel. [phone]

Fully Locked

Safety Harness

3

www.DeltaChildren.com

CHILD SAFETY HARNESS

3. To properly install the child safety harness, take
the strap lock and insert strap and entire strap
buckle into the slot on back of chair (Fig 3).

Slot on back

chair

Fig. 3

4. Flip seat over and make sure the strap buckle
lays flat and pulls against the back of the chair.
Repeat steps for each (3) strap lock. Make sure
all (3) strap locks and laying flat against chair
bottom. See figure 4 and 4a for reference. For
removal of child harness pull on end strap of
strap lock and glide entire strap lock through
the slots on chair. Repeat (3X) for complete
removal of harness.

Fig. 4

Fig. 4a

Customer Service Tel. [phone]

4

www.DeltaChildren.com

WARNING: When not buckled in seat, children can escape and fall suddenly.
WARNING: Always use with the restraint belt.
WARNING: Only use the seat on floor or level ground surface.
WARNING: Never use on raised surfaces such as tables, counters, chairs, beds, or near stairs. Even a

belted baby can cause the seat to slide or move off raised surfaces.

WARNING: Always stay with and watch your baby during use.
WARNING: Never use the floor seat in or near water to avoid drowning.

INFANT CHAIR ASSEMBLY

NOTE: SEAT COVER IS REVERSIBLE

1.

Flip floor seat over to see bottom. (Fig 5).

2.

Find the bent top leg seat tube, press in the
push button locking tab before sliding the
bent top leg seat tube into seat housing posts.
Once the bent top leg seat tube is fully seated
into the seat housing post, release the push
button locking tab so the locking tab is securely
fastened into the corresponding seat housing
post through hole. The bent top leg seat tube
should also have the seat tube post locked into
the slot on the seat housing post on the back
side of the seat posts. (Fig. 6)

1.

Fig. 5

Bent Top Leg Seat Tube

2.

3.

"Click"

To make sure they are securely locked in
place, pull upward on the bent top leg seat
tube.

Customer Service Tel. [phone]

Push Button

Lock Open

Fig. 6

5

Fully Locked

Position

www.DeltaChildren.com

INFANT CHAIR ASSEMBLY

3.

Located all (4) feet. Slide each foot onto the
bottom of each infant / toddler straight extension
tube (Fig. 7)

Find all (4) bottom infant / toddler straight

4.
extension tubes with feet attached and push
into all (4) bent top leg seat tubes (Fig 8). Make
sure the push buttons, located at the top of
every tube, are securely locked “clicked” in
place (Fig 8a). To make sure they are securely
locked in place pull upward on extension tube.

Straight

Extension

Tube

Fig. 7

"Click"

Flip over infant chair and place on level

5.
surface. All (4) feet should be flat against
the floor (Fig 9c). Line up left and right child
tray grooves with left and right child seat tray
posts (Fig 9a). Once tray and tray posts are
lined up, rotate tray downward to lock tray
over seat tray locking tabs (Fig 9b). Child tray
is securely locked in place when seat tray
locking tabs "click" into place and are through
tray opening. Pull upward on tray to make
sure in a fully locked position.

• NOTE: Child must be put into seat and
harness must be securely locked in place
around child (Fig 9d). Please refer to Fig 4-5
on page 5 for proper use of harness before
use.

Fig. 8

Fully Locked

Position

Fig. 8a

Fig. 9a

"Click"

Fig. 9b

Fig. 9

Customer Service Tel. [phone]

Fully Locked

Safety Harness

6

Fig. 9c

Fig. 9d

www.DeltaChildren.com

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF HIGH CHAIR. KEEP
INSTRUCTIONS FOR FUTURE USE. INCORRECT ASSEMBLY MAY MAKE THE HIGH
CHAIR UNSAFE. FAILURE TO FOLLOW THESE WARNINGS AND INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.

WARNING! The child should be secured in the high chair at all times by the restraining system,

either in the reclining or upright position. The tray is not designed to hold the child in the chair. It
is recommended that the high chair be used in the upright position only by children capable of
sitting upright unassisted.

WARNING! Prevent serious injury or death from falls or sliding out.
Always secure child in the restraint.

NEVER leave child unattended.
DO NOT use the high chair until the child can sit up unaided.
DO NOT use the high chair unless all components are correctly fitted and adjusted.
WARNING! Make sure that any harness is correctly fitted.

Only use in a flat stable surface.
Ensure your high chair is fully erected before placing your child inside.
Ensure children are clear of all moving parts before making any adjustments.

NEVER move the high chair with your child inside.
NEVER adjust the seat height with child in high chair.
DO NOT allow your child to climb unassisted into, play with or hang onto your high chair. This is

not a toy.

CARE AND MAINTENANCE

IMPORTANT! Before assembly or each use of this high chair, inspect this high chair for
damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts
are missing or broken. Never substitute parts. Contact Delta Children’s Products Customer
Service Department at 1.800.377.3777 for replacement parts and instructions if needed.

Customer Service Tel. [phone]

7

www.DeltaChildren.com

HIGH CHAIR ASSEMBLY

NOTE: SEAT COVER IS REVERSIBLE

Flip floor seat over to see bottom. (Fig 10).

1.

Fig. 10

2.

Find the bent top leg seat tube and push all (4)
tubes into all (4) tube slots (Fig 11). Make sure
the push buttons, located at the top of every tube,
are securely locked “clicked” into place. The push
buttons should be seen through the seat support
posts (Fig 11a). To make sure they are securely
locked in place pull upward on bent top leg seat
tube.

Bent Top Leg

Seat Tube

1.

Push Button

Lock Open

Fig. 11

2.

Fig. 11a

"Click"

3.

Fully Locked

Position

Customer Service Tel. [phone]

8

www.DeltaChildren.com

HIGH CHAIR ASSEMBLY

Find all (4) center high chair extension tubes

3.
and push into all (4) bent top leg seat tubes
(Fig 12). Make sure the push buttons, located
at the top of every tube, are securely locked
“clicked” in place (Fig 12a). To make sure they
are securely locked in place pull upward on
extension tube.

Center High Chair

Extension Tube

"Click"

Fig. 12

Fully Locked

Position

Fig. 12a

Located all (4) feet. Slide each foot onto the

4.
bottom of each infant / toddler straight extension

tube and place off to side (Fig. 13)

Take all (4) bottom infant / toddler straight

5.
extension tubes with feet attached and push into

all (4) center high chair extension tubes (Fig 14).
Make sure the push buttons, located at the top
of every tube, are securely locked “clicked” into
place (Fig 14a). To make sure they are securely
locked in place pull upward on extension tube.

Straight

Extension

Tube

Center High Chair

Extension Tube

Fig. 13

"Click"

Customer Service Tel. [phone]

Fig. 14

Fig. 14a

9

www.DeltaChildren.com

HIGH CHAIR ASSEMBLY

6.

Flip over high chair and place on level
surface. All (4) feet should be flat against the
floor (Fig 15c). Line up left and right child
tray grooves with left and right child seat tray
posts (Fig 15a). Once tray and tray posts are
lined up, rotate tray downward to lock tray
over seat tray locking tabs (Fig 15b). Child
tray is securely locked in place when seat tray
locking tabs "click" into place and are through
tray opening. Pull upward on tray to make
sure in a fully locked position.

• NOTE: Child must be put into seat and
harness must be securely locked in place
around child (Fig 15d). Please refer to Fig 4-5
on page 5 for proper assembly of harness
before use.

Fig. 15a

Fig. 15b

"Click"

Fig. 15

Fig. 15c

Fully Locked

Safety Harness

Fig. 15d

Customer Service Tel. [phone]

10

www.DeltaChildren.com

WARNING: Only use the seat on floor or level ground surface.
WARNING: Never use on raised surfaces such as tables, counters, chairs, beds, or near stairs. Even a

belted baby can cause the seat to slide or move off raised surfaces.

WARNING: Always stay with and watch your baby during use.
WARNING: Never use the floor seat in or near water to avoid drowning.

TODDLER CHAIR ASSEMBLY

NOTE: SEAT COVER IS REVERSIBLE

1.

Flip floor seat over to see bottom. (Fig 16).

Fig. 16

2.

Find the bent top leg seat tube and push all (4)
tubes into all (4) tube slots (Fig. 17). Make sure
the push buttons, located at the top of every tube,
are securely locked “clicked” into place. The push
buttons should be seen through the seat support
posts (Fig 17a). To make sure they are securely
locked in place pull upward on bent top leg seat
tube.

Customer Service Tel. [phone]

11

Bent Top Leg

Seat Tube

Fig. 17a

1.

Push Button

Lock Open

2.

Fig. 17

3.

Fully Locked

Position

www.DeltaChildren.com

TODDLER CHAIR ASSEMBLY

Located all (4) feet. Slide each foot onto the

3.

bottom of each infant / toddler straight extension
tube and place off to side (Fig. 18)

Straight

Extension

Tube

Fig. 18

4.

Find all (4) bottom infant / toddler straight
extension tubes and push into all (4) bent top
leg seat tubes (Fig 19). Make sure the push
buttons, located at the top of every tube, are
securely locked “clicked” in place (Fig 19a). To
make sure they are securely locked in place pull
upward on extension tube.

Fig. 19

Fully Locked

Position

Fig. 19a

Customer Service Tel. [phone]

12

www.DeltaChildren.com

TODDLER CHAIR ASSEMBLY

5.

Flip over toddler chair and place on level surface.
All (4) feet should be flat against the floor (Fig
20a). Child safety harness can be removed for
toddler chair. Please see figures 4-5 on page 5
on how to removed child safety harness.

Fig. 20a

Fig. 20

Customer Service Tel. [phone]

13

www.DeltaChildren.com

WARNING: Prevent serious injury or death from sliding out, falls, or tipping over.
WARNING: Never leave child unattended.
WARNING: Never allow a child to push away from table.
WARNING: Secure to adult chair per instructions. Always check security of fit before use.
WARNING: Until child is able to get in and out of the booster seat without help (about 2 1/2 years old) the

child should be secured in the booster seat at all times by the restraining system. The tray is not designed
to hold the child in the chair.
WARNING: Use of the booster seat with children weighing more than 40 lbs, will cause excessive wear
and stress of the booster and may cause hazardous unstable condition to exist.

WARNING: Prevent serious injury or death. Do not use in motor vehicles.
WARNING: This booster seat is designed to be attached to an adult chair with minimum dimensions of

16 in. width, 16 in. depth and backrest height of 13 in.

BOOSTER SEAT ASSEMBLY

NOTE: SEAT COVER IS REVERSIBLE

1. Before attaching booster seat to chair the chair needs
to meet a certain size requirement as shown in the
diagram.

2.

Place the booster seat on a chair. Wrap the bottom
straps around the bottom of the chair and buckle
the straps (Fig 21).

Backrest

Customer Service Tel. [phone]

14

Fig. 21

www.DeltaChildren.com

BOOSTER SEAT ASSEMBLY

3.

When buckles "click", the straps are fully locked.
Pull the free end of the strap to tighten on the
chair. Check underneath chair to make sure
buckles are fully locked (Fig 22).

4.

Wrap the top straps around the back of the chair
and buckle the straps (Fig 23).

Fig. 22

5.

When buckles "click", the straps are fully locked.
Pull the free end of the strap to tighten seat
onto the chair. Check behind chair to make sure
buckles are fully locked before use (Fig 24).
Child harness must be securely locked in place
around child before use (Fig 24a).

• NOTE: Child must be put into seat and
harness must be securely locked in place
around child. Please refer to Fig 4-5 on page
5 for proper assembly of harness before use.

Customer Service Tel. [phone]

15

Fig. 23

Fig. 24

Fully Locked

Safety Harness

Fig. 24a

www.DeltaChildren.com

STORAGE

Located underneath the seat is a storage bag to
place unused parts. (Fig. 25)

Customer Service

Tel. [phone]

16

Fig. 25

www.DeltaChildren.com

Customer Service Tel. [phone]

www.DeltaChildren.com