Delta ups302R2002N0B0, ups302R2002N0B6, ups202R2002N035, ups202R2002N0B6, ups202R2002N0B0 Installation & Operation Manual

Delta UPS - Amplon Family

5013251901

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

Product Introduction

1

ON

SETUP

OFF

1kVA 2/ 3kVA

The R series UPS, available in 1kVA, 2kVA and 3kVA, is a single-phase on­line Uninterruptable Power Supply (UPS) system, which outputs reliable
sine-wave power to your electrical equipment. The product is designed with
advanced technology and high quality components. Its output power factor is
up to 0.9 and efficiency in on-line mode reaches 93% (for 2kVA/ 3kVA). The
unit not only protects your electrical equipment by providing secure and reliable

uninterruptable power supply but also produces greater electric power e󰀩ciency

at less cost.

The Amplon Family R series UPS is a light, compact and easy to use solution for
IT applications and features rated nominal power capacities of 1kVA, 2kVA and
3 kVA. Each kVA model has no internal battery but can be connected to at least
one external battery pack (user-supplied).

Safety Instructions

2

z

z

Placement and Installation

1. Read the Quick Guide carefully to ensure correct and safe usage of the
product.

2. Install the UPS in a well-ventilated area, away from rain, excess moisture,

dust, ammable gas or explosives.

3. To reduce the risk of fire or electric shock, install the UPS in a
temperature and humidity controlled indoor area free of conductive

contaminants. Please refer to

10

temperature and relative humidity.

4. Leave adequate space at least 15cm around each side of the UPS for
proper ventilation.

z

z

Connection warnings

1. Make sure the UPS is well grounded to avoid a possible risk of current
leakage.

2. The installation of protective devices (a DC non-fuse breaker or a DC
fuse) is highly recommended when the UPS is connected to the power
source and critical loads.

3. The protective devices connecting to the UPS must be installed near the
UPS and must be easily accessible for operation.

4. Do not use extension cord to connect the UPS to an AC outlet.

5. Do not plug the UPS input power cord into its own output receptacles.

6. Prior to moving or reconnecting the UPS, disconnect the AC input power

and ensure the UPS is powered o󰀨; otherwise, hazardous voltage may

still exist at the output receptacles of the UPS, which presents a possible
risk of current leakage.

7. If you don't use the output power cord came with the UPS, please ensure
the length of the output power cord is shorter than 10m.

ON

SETUP

OFF

Technical Specifications

for operating

z

z

Usage warnings

1. The UPS is an EMC Class A product, which may cause wireless interference
in your living environment. Precautions need to be taken to prevent possible
interference.

2. The UPS can be used to power computers and associated peripheral devices,
such as monitors, modems, cartridge tape drives, external hard drives, etc.

3. It is strictly forbidden to connect the UPS to:

- regenerative loads

- loads with half-wave controlled rectier circuit

- loads with asymmetrical current

4. The external slits and openings in the UPS are provided for ventilation. To
ensure reliable operation of the UPS and to protect the UPS from overheating,
these slits and openings must not be blocked or covered.

5. Before usage, you must allow the UPS to adjust to room temperature
(20°C~25°C) for at least one hour.

6. Do not splash any liquid on the UPS and be sure to prevent any foreign
material from dropping into the UPS. Do not put beverages on or nearby the
UPS.

OFF

7. In an emergency, hold and press the

button, and release the button after

you hear one beep to turn o󰀨 the UPS. Meanwhile, cut o󰀨 the mains to shut

down the UPS.

8. Never use cleaning liquid or spray to clean the UPS. Before cleaning, make
sure you have (1) completely shut down the UPS, (2) unplugged the UPS
from the power outlet, and (3) disconnected the unit from the external battery
pack(s).

9. Only qualied personnel can perform maintenance service. Do not open or

remove the covers or panels of the UPS to avoid high voltage electric shock.

10. You must contact Delta customer service if either of the following events
occur:

- Liquid is poured or splashed on the UPS.

- The UPS does not run normally after carefully following the instructions in
this Quick Guide.

z

z

Battery Precautions

1. Do not dispose of the battery or batteries in a re. The batteries may explode.

Do not open or damage the battery or batteries. The released electrolyte is
harmful to the skin and eyes and may be toxic.

2. Servicing batteries and battery packs should be performed or supervised by

qualied service personnel who are knowledgeable in batteries, battery packs

and the required precautions.

3. The risk of dangerous voltage is possible when the batteries are still
connected to the UPS even though the UPS is disconnected from the mains.

Do not forget to disconnect the battery cable to completely cut o󰀨 the battery

source.

4. Only use the same type of batteries from the same supplier. Never use old,

new and di󰀨erent Ah batteries at the same time.

5. A battery can present a risk of electrical shock and high short circuit current.
The following precautions should be observed when working on batteries:

- Remove watches, rings or other metal objects.

- Use tools with insulated handles.

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect the charging source prior to connecting or disconnecting
battery terminals.

6. Do not reverse or short circuit the polarity + and – when connecting the
batteries because this will destroy the device and constitute a risk of electric

shock or re.

WARNING:

1. Even though the UPS is disconnected from the mains, a battery may

still present electrical shock and short circuit current hazard. Ensure to
cut o󰀨 the battery source prior to the UPS maintenance.

2. When the external battery pack(s) is(are) connected to the UPS, the
installation of the protective devices (a DC non-fuse breaker or a DC
fuse) is required to protect the unit.

Standard Compliance

3

z

z

CE

z

z

IEC/ EN 62040-1

z

z

IEC/ EN 62040-2 Category C2

Packaging List

4

The UPS package contains the following items. Please check if any item is missing. If
there is anything missing, please immediately contact the dealer.

z

z

UPS102/ 202/ 302R2002N035

1

ON

SETUP

OFF

6 8

2

Delta UPS - Amplon Family

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

7 9

3 4

×2

5

×4

×4

×4

10

No. Item Q’ty 1K 2/ 3K

1

z

z

UPS 1 PC

2

Installation & Operation Quick Guide 1 PC

3

Battery Wire 1 PC

4

Bracket Ear 1 SET

5

Battery Cable Tie 1 SET

6

USB Cable 1 PC

7

Input Power Cord 10A 1 PC

8

Input Power Cord 16A 1 PC

9

Output Power Cord 10A 1 PC

10

Output Power Cord 16A 1 PC

UPS102/ 202/ 302R2002N0B6

1

ON

SETUP

OFF

2

Delta UPS - Amplon Family

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

3 4

5

×4

×2

×4

×4

No. Item Q’ty 1K 2/ 3K

1

UPS 1 PC

2

Installation & Operation Quick Guide 1 PC

3

Battery Wire 1 PC

4

Bracket Ear 1 SET

5

Battery Cable Tie 1 SET

6

USB Cable 1 PC

7

Input Power Cord 10A 1 PC

8

Input Power Cord 16A 1 PC

Rear Panel

5

UPS102R2002N035 & UPS102R2002N0B6

1

2

RS-232

3 4

INPUT BREAKER
250Vac.10A

AC INPU T

6

MINI SLOT

EXTERNAL BATT. CONNEC TOR

24V DC 40A

5

7

8

OUTPUT SOCKET

UPS102R2002N0B0

1

2

RS-232

3 4

INPUT BREAKER
250Vac.10A

9

AC INPU T

6

MINI SLOT

EXTERNAL BATT. CONNEC TOR

24V DC 40A

5

7

8

OUTPUT SOCKET

UPS202R2002N035 & UPS202R2002N0B6 & UPS302R2002N0B6

6 8

No. Item Q’ty 1K 2/ 3K

1

UPS 1 PC

2

Installation & Operation Quick Guide 1 PC

3

Battery Wire 1 PC

4

Bracket Ear 1 SET

5

Battery Cable Tie 1 SET

6

USB Cable 1 PC

7

Input Power Cord 10A 1 PC

8

Input Power Cord 16A 1 PC

9

Output Power Cord 10A 1 PC

10

Output Power Cord 16A 1 PC

z

z

UPS102/ 202/ 302R2002N0B0

1

ON

SETUP

OFF

5 7

7 9

2

Delta UPS - Amplon Family

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

3 4

6

10

1

MINI SLOT

RS-232

2

3 456

8

AC INPUT

INPUT BREAKER

250V AC.20A

EXTERNAL BATT. C ONNECTOR

48V DC 40A

OUTPUT SOC KET

10A MAX. PER OUTLE T

7

UPS202R2002N0B0 & UPS302R2002N0B0

1

6

MINI SLOT

RS-232

2

3 4

8

OUTPUT SOCKET

10A MAX. PER OUTLE T

9

5

AC INPUT

INPUT BREAKER

250V AC.20A

EXTERNAL BATT. C ONNECTOR

48V DC 40A

7

UPS302R2002N035

6

1

×4

×2

×4

MINI SLOT

RS-232

×4

8

2

Continue to the Next Page

3 4

8

OUTPUT SOC KET

10A MAX. PER OUTLE T

5

AC INPUT

INPUT BREAKER

EXTERNAL BATT. C ONNECTOR

72V DC 40A

L N

UPS O UTPUT

TERMINAL BLOCK

7



250V AC.20A

www.deltapowersolutions.com

1/4

No. Item Functions

Hz

KW

KVA

AH

MIN

V

%

SETIN OUTBATT°CLOAD TEST

W

KVA

AH

N

%

SETIN OUTBATT°CLOADTEST

SETUP

1

RS-232 Port

For communicating with a PC to monitor the status of the UPS. UPSentry 2012
Software is required. Please download it from http://www.deltapowersolutions.
com/en/mcis/software-center.php.

NOTE: Do not use the USB port and the RS-232 port at the same time.

2

USB Port

3

Fan(s) For cooling and ventilation purpose.

4

Input Breaker

AC Input

5

(Input Socket)

6

Mini Slot

If you connect the USB cable to the USB port, the RS-232 port will be
disabled right away.

Prevents the UPS from damage caused by high current and protects the utility
power from further damage when the UPS fails.

Connects the UPS to the mains.

Connects to a Mini SNMP, Mini Relay I/O or Mini MODBUS card (optional) to
manage the UPS over the network.

Connects to the external battery pack(s) to extend back up time (+, -, and

External Batt.

7

Connector

terminals are included).
1 kVA : 24Vdc.40A
2 kVA : 48Vdc.40A
3 kVA : 72Vdc.40A

Output Socket

8

& UPS Output
Terminal Block

Connects the loads to the UPS. The UPS output terminal block is only applicable
for UPS302R2002N035.

For mounting the anti-insect net (optional) to prevent insects from entering into

Anti-Insect Net

9

Mounting holes

the UPS.

Only applicable for the UPS models ending with su󰀩x B0 (UPS102R2002N0B0,

UPS202R2002N0B0, and UPS302R2002N0B0).

Operational Panel

6

6.2 Multi-function Buttons

Icon(s) Description

z

z

Buzzer O󰀨: When the buzzer is on, press the button for 0.1 second to turn the buzzer o󰀨.

shown on the

16-segment

The code

display

Setup Item

Meaning

Standby

mode

On-line

mode

Bypass

mode

Battery

mode

ECO

mode

Frequency

converter

mode

In setup mode, the button is used to conrm or change your parameter. For more details,

please refer to 6.2.1 Setup Mode.

ALM

z

z

ON

Turn On: Press and hold the button for 3 seconds, and release it after you hear one beep.

z

z

Battery Test: Only applicable for on-line mode. Press and hold the button for 3 seconds,
and the UPS will transfer into battery mode to perform a battery test. After the battery test

BUZ Buzzer Setup V V V V V V

Overload Alarm

Setup

V V V V V V

completes, the LCD will show the test result and the UPS will return to on-line mode auto­matically.

NOTE: The UPS will not perform the battery test if the batteries are not fully

BYP

Bypass Range

Setup

V V V V V V

charged.

z

z

Scrolling Up/ Increasing Number: Press the button for 0.1 second to go to the previous
display or to increase number. In setup mode, press the button for 0.1 second to go to the

CAP

previous parameter.

OFF

z

z

Turn O󰀨: Press and hold the button for 3 seconds, and release it after you hear one beep.

z

z

Fault Clear: When the UPS has a fault condition, press and hold the button for 3 seconds,

STG

release it after you hear one beep and the UPS will clear the fault condition.

NOTE: When the UPS clears the fault condition, it means that the buzzer/ warning

AST

message has been turned o󰀨. To eliminate the fault detected, please refer

to

Troubleshooting

8

z

z

Scrolling Down/ Decreasing Number: Press the button for 0.1 second to go to the next

for relevant solutions.

PF

display or to decrease number. In setup mode, press the button for 0.1 second to go to the
next parameter.

RST

z

z

ON

Entering into the setup mode

Press the

and ON buttons at the same time for 3 seconds

into the setup mode.

z

z

Exiting from the setup mode

When the UPS is in setup mode, press the
seconds to exit the setup mode.

and the UPS will enter

and ON buttons at the same time for 3

NOTE:

1

: Both of the '

*

can tell whether the UPS is in '
on the 7-segment display.

Battery Capacity

Setup

Battery String

Setup

Auto-Start To On-

line Setup

Power Factor

Setup

Restore Default

Setup

Inverter Voltage Setup

V V V V V V

V V V V V V

V X V X X X

V X V X X X

V X V X X X

Inverter Frequency Setup

Voltage

' and '

' or in

'Frequency

' setup by checking the information shown

' use the same code, but you

IN

RUN TIME

ECO

MIN

V

LOAD

TEST

OFF

°C

AH
V
Hz
KVA
KW
MIN

%

SETUP

SET

IN OUT BATT

ON

6.1 LED Indicators

Icon(s) Description

Indicates the output status.

z

z

ON (green): Output; OFF: No output.

1. ON: The UPS detects an internal fault or an environmental fault. The error code will appear
on the 16-segment display.

2. Flashing: When the icon is ashing, it would be accompanied with other icon(s) to indicate
the according warning message(s).
For example:

): There is no battery or battery replacement is required.

a. (

V
Hz

b.

c. (

(

IN

RUN TIME

: Overload.

)

K
MI

): Charging voltage is too high or too low.

6.1 LED Indicators

6.3 LCD Display

6.4 7-segment Display

6.5 16-segment Display

6.2 Multi-function Buttons

NOTE:

1. When the LCD display gets dim, press any of the above-mentioned buttons to wake up the LCD
display and enable each button function.

2. Only qualied service personnel can perform setup action.

3. For more information about the setup mode, please refer to 6.2.1 Setup Mode.

6.2.1 Setup Mode

Please note that only qualied service personnel can perform setup action. In setup mode, you can set up the

following items. For some settings, they can’t be set in certain operation modes. Please refer to the table below
for relevant information.

Setup Item

The code

shown on the

16-segment

Meaning

Standby

mode

On-line

mode

Bypass

mode

Battery

mode

ECO

mode

display

INV *

INV *

1

1

Setup

Inverter

Frequency

V X V X X X

V X V X X X

Inverter Voltage

Setup

COV

STB

Frequency

Converter Setup

Standby Bypass

Setup

V X V X X X

V V V V V V

ECO ECO Setup V V V V V X

Frequency

converter

mode

The table below lists each setup item's setting parameters.

Setup Item

The code

shown on the

16-segment

Meaning

Setting Parameters*

display

INV Inverter Voltage Setup 200V, 208V, 220V (Default), 230V, 240V

INV Inverter Frequency Setup 50Hz (Default), 60Hz

COV Frequency Converter Setup OFF (Default), ON*

STB Standby Bypass Setup OFF, ON (Default)*

2

3

ECO ECO Setup OFF (Default), ON

ALM Overload Alarm Setup 60%, 70%, 80%, 85%, 90%, 95%, 100%, 105% (Default)

BUZ Buzzer Setup ENA (Enable) (Default), DIS (Disable)

BYP Bypass Range Setup

5%, 6%, 7%, 8%, 9%, 10%, 11%, 12%, 13%,

14%, 15% (Default), HI1, HI2, HI3*

0AH (Default), 5AH, 7AH, 9AH, 12AH, 15AH,

CAP Battery Capacity Setup

24AH, 33AH, 38AH, 40AH, 50AH, 65AH,

80AH, 100AH, 120AH, 150AH, 200AH*

STG Battery String Setup 0 (Default), 1, 2, 3, 4, 5, 6, 7, 8, 9*

1

4

5

5

www.deltapowersolutions.com

2/4

Continue to the Next Page

