Delta UPS202R2000B0B2, UPS102R2000B1B1, UPS302R2000B0B1, UPS202R2000B0B1, UPS302R2000B1B1 Installation & Operation Manual

Delta UPS - Amplon Family

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

Product Introduction

1

ON

ON

SETUP

OFF

1kVA 2kVA

ON

SETUP

OFF

3kVA

The R series UPS, available in 1kVA, 2kVA and 3kVA, is a single-phase on­line Uninterruptable Power Supply (UPS) system, which outputs reliable
sine wave power to your electrical equipment. The product is designed with
advanced technology and high quality components. Its output power factor
is up to 0.9, and efficiency in on-line mode reaches 93% (for 2kVA/ 3kVA).
The unit not only protects your electrical equipment by providing secure and
reliable uninterruptable power supply but also produces greater electric power

efciency at less cost.

The Amplon Family R series UPS is a light, compact and easy to use solution
for IT applications and features rated nominal power capacities of 1kVA, 2kVA
and 3kVA. Each kVA model has internal batteries and each model can be
connected to the optional Delta external battery pack(s). The nominal rating
voltage of the internal batteries is 24V (1kVA), 48V (2kVA) and 72V (3kVA).
Please see the table below for details.

Model No. Power Rating Remarks

UPS102R2000B0B1
UPS102R2000B1B1

1kVA

UPS102R2000B0B2

UPS202R2000B0B1
UPS202R2000B1B1

2kVA

UPS202R2000B0B2

SETUP

OFF

With internal batteries (2
pcs 9Ah sealed lead-acid
batteries; battery voltage:
24Vdc)

With internal batteries (4
pcs 9Ah sealed lead-acid
batteries; battery voltage:
48Vdc)

Model No. Power Rating Remarks

UPS302R2000B0B1
UPS302R2000B1B1
UPS302R2000B0B2

3kVA

With internal batteries (6 pcs
9Ah sealed lead-acid batteries;
battery voltage: 72Vdc)

NOTE:

1. The R Series UPS can connect to the optional Delta external battery
pack(s).

2. For more information about the optional Delta external battery pack(s),
please contact your dealer.

Safety Instructions

2

z

z

Placement and Installation

1. Read the Quick Guide carefully to ensure correct and safe usage of the
product.

2. Install the UPS in a well-ventilated area, away from rain, excess moisture,

dust, ammable gas or explosives.

3. To reduce the risk of re or electric shock, install the UPS in a temperature

and humidity controlled indoor area free of conductive contaminants. Please

Technical Specifications

refer to

10

for operating temperature and relative

humidity.

4. Leave adequate space at least 15cm around each side of the UPS for proper
ventilation.

z

z

Connection warnings

1. Make sure the UPS is well grounded to avoid a possible risk of current
leakage.

2. The installation of protective devices (a DC non-fuse breaker or a DC fuse)
is highly recommended when the UPS is connected to the power source and
critical loads.

3. The protective devices connecting to the UPS must be installed near the UPS
and must be easily accessible for operation.

4. Do not use extension cord to connect the UPS to an AC outlet.

5. Do not plug the UPS input power cord into its own output receptacles.

6. Prior to moving or reconnecting the UPS, disconnect the AC input power and
ensure the UPS is powered off; otherwise, hazardous voltage may still exist
at the output receptacles of the UPS, which presents a possible risk of current
leakage.

7. Please ensure the length of the output power cord is shorter than 10m.

z

z

Usage warnings

1. The UPS is an EMC Class A product, which may cause wireless interference
in your living environment. Precautions need to be taken to prevent possible
interference.

2. The UPS can be used to power computers and associated peripheral devices,
such as monitors, modems, cartridge tape drives, external hard drives, etc.

3. It is strictly forbidden to connect the UPS to:

- regenerative loads

- loads with half-wave controlled rectier circuit

- loads with asymmetrical current

4. The external slits and openings in the UPS are provided for ventilation.
To ensure reliable operation of the UPS and to protect the UPS from
overheating, these slits and openings must not be blocked or covered.

5. Before usage, you must allow the UPS to adjust to room temperature
(20°C~25°C) for at least one hour.

6. Do not splash any liquid on the UPS and be sure to prevent any foreign
material from dropping into the UPS. Do not put beverages on or nearby
the UPS.

OFF

7. In an emergency, hold and press the

button, and release it after you

hear one beep to turn off the UPS. Meanwhile, cut off the mains to shut
down the UPS.

8. Never use cleaning liquid or spray to clean the UPS. Before cleaning,
make sure you have (1) completely shut down the UPS, (2) unplugged the
UPS from the power outlet, and (3) disconnected the unit from the Delta
external battery pack(s).

9. Only qualied personnel can perform maintenance service. Do not open

or remove the covers or panels of the UPS to avoid high voltage electric
shock.

10.You must contact Delta customer service if either of the following events
occur:

- Liquid is poured or splashed on the UPS.

- The UPS does not run normally after carefully following the instructions

in this Quick Guide.

z

z

Battery Precautions

1. Do not dispose of the battery or batteries in a fire. The batteries may
explode. Do not open or damage the battery or batteries. The released
electrolyte is harmful to the skin and eyes and may be toxic.

2. Servicing batteries and battery packs should be performed or supervised

by qualied service personnel who are knowledgeable in batteries, battery

packs and the required precautions.

3. The risk of dangerous voltage is possible when the batteries are still
connected to the UPS even though the UPS is disconnected from the
mains. Do not forget to disconnect the battery cable to completely cut off
the battery source.

4. To ensure battery performance, idle batteries must be fully recharged
every three month if the UPS needs to be stored for an extended period of
time. Whenever you recharge the batteries (internal and external), please
fully charge them until the Battery Level Bar Graph

shown on the UPS’s

LCD is fully on.

5. Since new batteries often do not provide full capacity after an initial
charge, it may be necessary to carry out a number of discharge/ recharge
cycles before optimum performance is achieved.

www.deltapowersolutions.com

5013252501

1/8

Continue to the Next Page



6. Only use the same type of batteries from the same supplier. Never use old,
new and different Ah batteries at the same time.

7. A battery can present a risk of electrical shock and high short circuit current.
The following precautions should be observed when working on batteries:

- Remove watches, rings or other metal objects.

- Use tools with insulated handles.

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect the charging source prior to connecting or disconnecting

battery terminals.

8. Do not reverse or short circuit the polarity + and – when connecting the
batteries because this will destroy the device and constitute a risk of electric

shock or re.

WARNING:

1. Even though the UPS is disconnected from the mains, a battery may
still present electrical shock and short circuit current hazard. Ensure
to cut off the battery source prior to the UPS maintenance.

2. When the Delta external battery pack(s) is(are) connected to the
UPS, the installation of the protective devices (a DC non-fuse breaker
or a DC fuse) is required to protect the unit.

Standard Compliance

3

z

z

CE

z

z

IEC/ EN 62040-1

z

z

IEC/ EN 62040-2 Category C2

Packaging List

4

The UPS package contains the following items. Please check if any item is
missing. If there is anything missing, please immediately contact the dealer.

z

z

UPS102/ 202/ 302R2000B0B1

No. Item Q’ty 1K 2/ 3K

1

UPS 1 PC

Installation & Operation

2

Quick Guide

3

Bracket Ear 1 SET

4

USB Cable 1 PC

5

Input Power Cord 10A 1 PC X

6

Input Power Cord 16A 1 PC X

z

z

UPS102/ 202/ 302R2000B1B1

1 3

ON

SETUP

OFF

2

Delta UPS - Amplon Family

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

1 PC

×2

4

×4

×4

×4

No. Item Q’ty 1K 2/ 3K

1

UPS 1 PC

Installation & Operation

2

Quick Guide

3

Bracket Ear 1 SET

4

USB Cable 1 PC

5

Input Power Cord 1 PC

z

z

UPS102/ 202/ 302R2000B0B2

1 3

2

1 PC

4

Rear Panel

5

UPS102R2000B0B1

1

2

5

UPS202R2000B0B1

1

2

3 4 6

INPUT BREAKER

250

RS-232

AC INP UT

3

RS-232

V AC

.10A

5

6

MINI SLOT

MINI SLOT

EXTERNAL BATT. CONNE CTOR

24V DC 40A

7

5

AC INPUT

EXTERNAL BATT. C ONNECTO R

48V DC 40A

4

INPUT BREAKER

250V AC.20A

OUTPUT SOC KET

7

8

OUTPUT SOCKET

8

10A MAX. PER OUTLE T

UPS302R2000B0B1

1

5

2

3

RS-232

6

MINI SLOT

5

AC INPUT

EXTERNAL BATT. C ONNECTO R

72V DC 40A

7

4

INPUT BREAKER

250V AC.20A

8

OUTPUT SOC KET

10A MAX. PER OUTLE T

1

ON

SETUP

OFF

4

www.deltapowersolutions.com

2

Delta UPS - Amplon Family

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

5

×2

Delta UPS - Amplon Family

3

×4

×4

ON

SETUP

OFF

R Series, Single Phase

1/ 2/ 3 kVA

Installation & Operation Quick Guide

ENGLISH

×2

×4

×4

×4

×4

6

No. Item Q’ty 1K 2/ 3K

1

UPS 1 PC

Installation & Operation

2

Quick Guide

3

Bracket Ear 1 SET

4

USB Cable 1 PC

5

Input Power Cord 1 PC

1 PC

UPS102R2000B1B1

1

2

3

RS-232

4

INPUT BREAKER

250

V AC

.10A

AC INPUT

5

6

MINI SLOT

EXTERNAL BATT. C ONNECTO R

24V DC 40A

7

Continue to the Next Page



8

OUTPUT SOC KET

2/8

UPS202R2000B1B1

Hz

KW

KVA

AH

MIN

V

%

SETIN OUTBATT°CLOAD TEST

W

KVA

AH

N

%

SETIN OUT BATT°CLOADTEST

IN

1

2

3 4

RS-232

UPS302R2000B1B1

1

2

3 456

RS-232

UPS102R2000B0B2

1

2

3 4

RS-232

UPS202R2000B0B2

1

2

3

RS-232

INPUT BREAKER

250

V AC

AC INPUT

5

6

MINI SLOT

MINI SLOT

.10A

MINI SLOT

AC INPUT

5

AC INPUT

EXTERNAL BATT. C ONNECTO R

AC INPUT

EXTERNAL BATT. C ONNECTO R

6

MINI SLOT

EXTERNAL BATT. C ONNECTO R

24V DC 40A

7

46

INPUT BREAKER

250V AC.20A

5

48V DC 40A

7

72V DC 40A

7

INPUT BREAKER

250V AC.20A

INPUT BREAKER

250V AC.20A

8

OUTPUT SOCKET

8

OUTPUT SOCKET

OUTPUT SOCKET

EXTERNAL BATT. C ONNECTO R

48V DC 40A

OUTPUT SOCKET(10A MAX. PER OUTLE T)

UPS302R2000B0B2

INPUT BREAKER

250V AC.20A

5

4

OUTPUT SOCKET(10A MAX. PER OUTLE T)

1

3 7

RS-232

6

MINI SLOT

AC INPUT

2

No. Item Functions

1

RS-232 Port

Communicates with a PC, so you can monitor
the status of the UPS. (UPSentry 2012 Software
is required. Please download it from http://www.
deltapowersolutions.com/en/mcis/software-center.

EXTERNAL BATT. C ONNECTO R

72V DC 40A

8

Operational Panel

6

IN

RUN TIME

MIN

V

SETUP

ECO

SET

IN OUT BATT

ON

LOAD

TEST

OFF

°C

AH
V
Hz
KVA
KW
MIN

1

%

3

2

php).

2

USB Port

NOTE: Do not use the USB port and the RS-

232 port at the same time. If you connect the
USB cable to the USB port, the RS-232 port
will be disabled right away.

1

6.1 LED Indicators

2

6.2 Multi-function Buttons

6.3 LCD Display

3

Fan Cools and ventilates the UPS.

8

3

6.4 7-segment Display

Prevents the UPS from damage caused by high

4

Input Breaker

current and protects the utility power from further

6.5 16-segment Display

damage when the UPS fails.

AC Input

5

(Input Socket)

6

Mini Slot

Connects the UPS to the mains.

Connects a Mini SNMP, a Mini Relay I/O or a Mini
MODBUS card (optional) to manage the UPS.

6.1 LED Indicators

Icon(s) Description

Indicates the output status.

z

z

ON (green): Output; OFF: No output.

Connects the Delta external battery pack(s) to

87

External Batt.

7

Connector

extend back up time (+, -, and
included).

1 kVA : 24Vdc.40A

terminals are

2 kVA : 48Vdc.40A
3 kVA : 72Vdc.40A

Output

8

Sockets

Connect the loads to the UPS.

1. ON: The UPS detects an internal fault or an environmental
fault. The error code will appear on the 16-segment display.

2. Flashing: When the icon is ashing, it would be accompanied
with other icon(s) to indicate the according warning message(s).
For example:

a. (

): There is no battery or battery replacement is required.

V
Hz

b.

c. (

(

RUN TIME

: Overload.

)

K
MI

): Charging voltage is too high or too low.

www.deltapowersolutions.com

3/8

Continue to the Next Page

