INSTALLATION AND OPERATING INSTRUCTIONS
VENTILATION FAN/LED LIGHT/ LED NIGHT-LIGHT
READ AND SAVE THESE INSTRUCTIONS
GENERAL SAFETY INFORMATION
MODEL SIG110LED
Page 1.
1. Make sure that the electric service supply voltage is AC 120V,
60Hz.
2. Follow all local electrical and safety codes, as well as the
National Electrical Code (NEC) and the Occupational Safety
and Health Act (OSH Act).
3. Always disconnect the power source before working on or
near the ventilating fan, motor or junction box.
4. Protect the power cord from sharp edges, oil, grease, hot
surfaces, chemicals or other objects.
5. Do not kink the power cord.
6. Do not install the unit where ducts are
Fig. A.
7. Provide suction parts with proper ventilation.
8. This unit is UL listed for use over a bathtub or shower when
installed in a GFCI (Ground Fault Circuit Interrupter) protected
branch circuit.
9. These ventilating fans are intended for residential usage only.
congured as shown in
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufactu
2. Before servicing or cleaning the unit, switch the power o at
the service panel and lock the service disconnecting means to
prevent the power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the
service panel.
3. Installation work and electrical wiring must be done by
qualied person(s) in accordance with all applicable codes
and standards, including re-rated c
4. Sucient air is needed for proper combustion and exhausting
of gases through the ue (chimney) of fuel burning
equipment to prevent back drafting. Follow the heating
equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE) and
local code authorities.
5. When cutting or drilling into a wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducte
outdoors.
7. If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected
to a GFCI – protected branch circuit.
rer.
onstruction.
d ventilating fans must always be vented to the
8. Do not use this unit with any other solid-state control device.
Solid-state controls may cause harmonic distortion, which can
cause a motor humming noise.
9. NEVER place a switch where it can be reached from a tub or
shower.
10. Not to be installed in a ceiling thermally insulated to a value
ater than R40. (This is required for installation in Canada
gre
only).
11. Do not open/disassemble the LED light engine.
Turning angle too large Duct shrink
ydob eht raen woblEswoble ynam ooT
Body
Fig. A
CAUTION
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking areas. (Fig. B)
3. This product must properly connect to the grounding
conductor of the supply circuit.
4. To reduce the risk of injury to persons, install the fan at least
8.2 feet (2.5 m) above the oor.
Cooking area
Do not install above or
inside this area
45
°
Cooking
Equipment
Fig. B
45
°
floor
SUPPLIED ACCESSORIES
Part name Appearance Quantity
Grille
Tapping Screw
4x25)
(ψ
Screw
#8-32x1/4”
Duct connector 1
Duct Screw
(M4x12)
13”(318.5)
13”(318.5)
Inches (mm)
1
4
4
1
2
2
1. Using suspension brackets
1-1. Sliding suspension brackets are provided to allow for
positioning of the housing anyw here between joists up to a
span of 24”.
1-2. Insert the suspension brackets into the channels on the
housing. Make sure the tabs face up as shown. (Fig. C)
1-3. Extend the suspension brackets to t the width of the joists.
Hold the fan in place by wrapping the suspension bracket tabs
around the bottom of the joist. Make sure the fan body is level
and perpendicular to the joist. (Fig. D & E)
1-4. Ensure that the distance between the ceiling and fan body is
appropriate for mounting the grille.
1-5. Secure the suspension brackets to the joists with nails or by
using the tapping screws ( 4x25) through holes near nails.
1-6. Secure the suspension bracket to the fan body using the
screws (#8-32 x 1/4").
1-7. Follow steps 2 to 6 of the installation to complete the
installation work.
INSTALLATIONS
Proper insulation around the fan to minimize building heat loss
and gain.
Roof cap
(with built-in
Short piece of exible
duct helps alignment
and absorbs
sound
Fan housing
Seal gap
around housing
Caulk termination
to duct
damper)
Wall cap
(with built-in
damper)
Attach Duct Connector
Option 1. Attach the duct connector from outside, and secure
using the duct screw (M4X12).
Inse rt tab into
slot i n ho using
Duc t screw (M4X12)
from Parts B ag
Suspension
Bracket I
Suspension
Bracket II
Body
MODEL SIG110LED
ψ
Tab
Fig. C
Page 2.
Option 2. Attach the duct connector from the housing can inside,
and secure using the duct screw (M4X12).
Duct sc rew(M4X12)
from Pa rts Bag
Pull existing ductwork
into Housi ng
Insert tab into slot
in Hous ing
Note: Remove the tape from the damper and adaptor before
installation.
Fig. D
Fig. E
2. Duct connection
Inside
Tape
Outside
ON/OFF SWITCH
(purchase separately)
RED
YELLOW
SWITCH BOX
MODEL SIG110LED
Page 3.
BLACK
WHITE
GROUND
(bare)
Body
Ceiling
Duct
Gradient
1°~2°
Duct connector
Fig. F
2-1. Insert the duct into the duct connector and tape all ductwork
connections to make them secure and airtight. (Fig. F)
2-2. Install the duct with a gradient of 1°~2° to the outside.
3. Connect wiring
3-1. Follow all local electrical and safety codes.
3-2. NEVER place a switch where it can be reached from a tub or
shower.
3-3. Connect wires as shown in the wiring diagrams below.
JUNCTION BOX
RED
WHITE
YELLOW
WHITE
BLACK
WHITE
GREEN
SWITCH BOX
OFF
ON
LIGHT SWITCH
OFF
ON
NIGHT-LIGHT SWITCH
OFF
ON
POWER SWITCH
L
N
L
N
L
N
GRD
NIGHT-
LIGHT
SWITCH
LIGHT
SWITCH
POWER
SWITCH
120 VAC
LINE IN
WIRING
PLATE
3-4. Using quick connector, connect house power wires to
ventilating fan wires.
3-5. Using wire nut (not provided), connect house ground wire to
fan ground wire.
3-6. 14 AWG (2.1 mm
2
) is the smallest conductor that shall be used
for branch-circuit wiring.
4. Grille attachment
4-1. Insert the LED light connector into the main body. (Fig. G)
4-2. With the power on, check for abnormal vibrations or sounds.
4-3. Insert the mounting springs into the slots and mount the grille
to the body. (Fig. H)
Celling
QUICK CONNECTOR INSTRUCTIONS
To be sold only with installation instructions.
WARNING: Wiring must comply with all applicable electrical codes. Turn
OFF power before removing or installing connectors.
WARNING: COPPER TO COPPER ONLY. Do not use Aluminum wire.
CAUTION: Accessory part (quick connector) should meet installation
instructions.
NOTE: The connector is reusable on solid wires of the same wire gage or
smaller. Do not reuse the connector on stranded wires.
NOTE: Important wire information. Maximum temperature rating 105
O
F). 600 volts maximun for building wire and 1000 volts maximum in
(221
signs and lighting fixtures. The acceptable wire range includes:
Solid: 12-18 AWG
O
C
Quick
connector
House
wire
Product
wire
Strip wire 3/8"-1/2"
Grip the wire firmly and push the stripped end of the wire into the open
port of the connector. Use only one conductor per port.
Verify the stripped end of the wires is fully inserted to the back of the
connector.
LED light
connector
Grille
Fig. G
Fig. H
Slots
Spring
(K)
5. Operation
5-1. Turn the POWER switch on/o to operate the fan / LED light /
LED night light. The LED indicator will be green when the fan is
turned on.
MAINTENANCE WARNING:
Disconnect the power source before working on the unit. Routine
maintenance must be done every year.
CAUTION:
1. Never use gasoline, benzene, thinner or any other such
chemicals to clean the ventilating fan.
2. Do not allow water to enter the motor.
3. Do not soak resin parts in water over 60°C (140°F).
CLEANING
1. To remove the
grille, pull down the spring and power
connects of the LED light engine.
2. Wash and clean the grille carefully. CAUTION: Do not let water
into the LED light engine. (Use non-abrasive kitchen
detergent and wipe dry with a clean cloth.)
3. Remove dust and dirt from the ventilating fan.
4. Using a cloth dampened with non-abrasive kitchen detergent,
remove any dirt from ventilating fan. Wipe dry with a clean
cloth.
5. Replace the grille.
DIMENSIONS
SPECIFICATIONS-FAN
Model No.
SIG110LED
Note: Design and specications subject to change without notice.
Voltage
Frequency
(V )
120 60 13.1 110 10 23.0
(Hz)
Power
@ 0.1”SP
(W )
Air Flow
@ 0.1”SP
(CFM)
Weight
(lb.)
Power
@ 0.0SP
(W )
SPECIFICATIONS - LED LIGHT ENGINE
ITEM
DIMENSION（INCH）
MAIN LIGHT POWER CONSUMPTION（W）
NIGHT LIGHT POWER CONSUMPTION（W）
MAIN LIGHT LUMINOUS FLUX（LM）
CORRELATED COLOR
TEMPERATURE
LIGHT SOURCE LIFE（HOURS）
TRANSIENT PROTECTION
OPERATING FREQUENCY（HZ）
FCC QUALIFIED
ENERGY QUALIFIED
ROHS QUALIFIED
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY
Delta Electronics Inc. (“Delta Electronics”) warrants to the original
consumer purchaser in the USA that the Breez ventilation fan products
will be free from defects in material or workmanship. This warranty is
limited to three (3) years from the original date of purchase.
Limitations and Exclusions
1. During the warranty period, a replacement for any defective product
will be supplied free of charge for installation by the consumer. The
warranty provided herein does not cover charges for labor or other
costs incurred in the troubleshooting, repair, removal, and installation
service.
2. All returns of defective parts or products must include the product
model number, and must be made through an authorized Delta
Electronics distributor. Authorized returns must be shipped prepaid.
Repaired or replacement products will be shipped by Delta Electronics
F.O.B. shipping point.
3. Delta Electronics shall not be liable for any indirect, incidental,
consequential, punitive, or special damages arising out of or in connection with products use or performance, regardless of the form of
action whether in contract, tort (including negligence), strict product
liability or otherwise.
4. This warranty does not extend to uorescent lamp starters and tubes.
5. The warranty does not cover if user does not comply with manufacturer’s
installation manual.
6. To qualify for warranty service, you must notify Delta Electronics at the
address or telephone number below.
7. Delta Electronics shall have no liability to the original owner-user with
respect to any defect caused by abuse, misuse, neglect, improper
transportation or storage, improper testing, improper installation,
improper operation, improper use, improper maintenance, improper
repair, improper alteration, improper modication, tampering or
accident of products or parts thereof, or unusual deterioration or
degradation of products or parts thereof due to a physical environment
beyond the requirements of products’ specications.
Address: 4405 Cushing Parkway, Fremont, CA 94538
US Toll Free Number: 1-888-979-9889
MODEL SIG110LED
Page 4.
SPEC.
8L×4.4W×1.4H
13
2
800
2700
30000（MIN.）
CLASS A
120
YES
YES
YES
LUc/LU STNEMERIUQER YTEFAS
Loading...