Delta Scottsdale Assembly And Use Manual

JULY 19, 2010 7151-R2

©2010 DELTA ENTERPRISE CORP.

Customer Service:

Web Site: www.deltachildrensproducts.com

Delta Children’s Products

114 West 26th Street
New York, NY 10001

Tele.212-645-9033

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.

If you have any questions or missing parts, contact us. DO NOT return product parts to the store
from where it was purchased before contacting Delta Children’s Products Customer Service.

.

Make sure that all pre-assembled parts are tight. The appearance of your product may be different
from that pictured in this booklet.

To register your product for important safety alerts and updates to your product
please visit http://deltaenterprise.com/register.asp

ADULT ASSEMBLY REQUIRED

DUE TO THE PRESENCE OF SMALL PARTS DURING

ASSEMBLY, KEEP OUT OF REACH OF CHILDREN UNTIL

ASSEMBLY IS COMPLETE.

READ ALL INSTRUCTIONS BEFORE

ASSEMBLY AND USE.

KEEP INSTRUCTIONS FOR FUTURE USE.

Flat Head
Screwdriver
(not supplied)

Required Tools

!

Conforms to

ASTM F1821

Safety Standards

TODDLER BED

WARNING ENTRAPMENT/STRANGULATION HAZARD

*INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT AND STRANGULATION. Failure to
follow these warnings and the assembly instructions could result in serious injury or death.
*Never use bed with children under 15 months.
*Never place bed near windows where cords from blinds or drapes may strangle a child.
*Do not place items with a string, cord, or ribbon around a child’s neck, such as hood strings or pacifier
cords.
*Do not suspend strings over a toddler bed for any reason.
*The users maximum weight shall not be greater than 50 lb (22.7kg).
*The mattress intended for use on the bed shall be a full-size crib mattress having minimum dimensions
of 51 5/8 in. (1310 mm) in length, 27 1/4 in. (690 mm) in width and 4 in. (100 mm) in thickness.

2

!

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.

NOTES ON CARE AND MAINTENANCE:

- Do not scratch or chip the finish.

- Inspect the product periodically, contact delta children's products for replacement parts or questions.

- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.

-Do not use abrasive chemicals.

-Do not spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

NOTES ON USE:

Keep children and others safe by following these simple rules:

- Do not allow any child to play on furniture

- Do not allow climbing on any piece of furniture.

- Do not allow hanging from any piece of furniture.

- Always monitor your child’s activity when in the nursery.

*Guardrails provided must be used to avoid the formation of a gap between the mattress and the bed
that could cause an entrapment.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.

A. HEADBOARD
TOP RAIL(1)

B. HEADBOARD(1)

H. LEFT BACK
SIDE RAIL (1)

K. FRONT SIDE RAIL(2)

L. CROSS SLAT(10)

M. CENTER CROSS SLAT(1)

N. GUARD RAIL(2)

P. CENTER LEG(2)

E. FOOTBOARD RAIL(1)

C. LEFT HEADBOARD LEG(1)

G. LEFT FOOTBOARD LEG(1)

D. RIGHT HEADBOARD LEG(1)

F. RIGHT FOOTBOARD LEG(1)

J. RIGHT BACK
SIDE RAIL (1)

3

A1. HEADBOARD
MIDDLE RAIL(1)

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.

V. BARREL NUT x 26

X. Φ8x40 mm WOOD DOWEL x 4

M4 ALLEN WRENCH SUPPLIED

Y. PLATE x 2

R. M6x90 mm BOLT x 4

U. M6x45 mm BOLT x 2

T. M6x63 mm BOLT x 14

4

S. M6x76 mm BOLT x 11

W. Φ4.5x30 mm METAL PIN x 2