OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
1 Revision: S1
03/27/2007
www.deltaww.com
1.25Gbps Upstream/1.25Gbps Downstream
GE-PON OLT Transceiver
FEATURES
RoHS compliant
IEEE802.3ah Gigabit Ethernet compliant
2x5 pin SFF package with SC pigtail fiber
1310nm Burst Mode 1.25Gbps receiver, and
1490nm Continuous Mode 1.25Gbps
transmitter
Build in Optical Isolator for extreme Return
Loss tolerance
Single +3.3V power supply
LVPECL electrical signal interface
LVTTL Tx Disable input and Rx Signal Detect
output
Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Description
DELTA’s GE-PON OLT transceiver
OPEP-33-B4L3R is designed for Gigabit Ethernet
Passive Optical Network transmission.
The module is contained in a 2x5 SFF
package with a 9/125um SC pigtail single mode
fiber.
The module consists 1490nm un-cool DFB
laser, InGaAs/InP APD, Preamplifier and WDM filter
in a high-integrated optical sub-assembly, and it
receives up to 1.25Gbps of burst-mode data at
1310nm, and transmits 1.25Gbps of continuous
data at 1490nm.
Application
IEEE 802.3ah 1000BASE-PX20-D
GE-PON OLT
Burst Mode Application
FTTx WDM Broadband Access
OPEP-33-B4L3R data link more than 20km in
9/125um single mode fiber.
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
2 Revision: S1
03/27/2007
www.deltaww.com
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note
Storage Temperature Ts -40 85 ºC
Storage Ambient Humidity HA 5 95 %
Power Supply Voltage VCC -0.3 4 V
Signal Input Voltage -0.3 Vcc+0.3 V
Receiver Damage Threshold +4 dBm
Lead Soldering Temperature T
SOLD
260 ºC
Lead Soldering Time t
SOLD
10 sec
2. Recommended Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Note
Ambient Operating Temperature TA 0 70 ºC
Without air flow
Ambient Humidity HA 5 95 %
Non-condensing
Power Supply Voltage VCC 3.13 3.3 3.47 V
Power Supply Current ICC 350 mA
Power Supply Noise Rejection 100 mVp-p
100Hz to 1MHz
Data Rate
1.25
-100ppm
1.25
1.25
+100ppm
Gbps
Transmission Distance 20+ km
3. Specification of Transmitter
Parameter Symbol Min. Typ. Max. Unit Note
Average Launched Power (B.O.L) PO
+3 +7
dBm Note (1)
Average Launched Power (E.O.L) PO
+2 +7
dBm Note (1)
Launched power (Peak.) PP
+10
dBm
Extinction Ratio ER
9
dB
Center Wavelength
λ
C
1480 1490 1500 nm DFB Laser
Spectrum Width (-20dB)
σ
0.44 nm Note (2)
Side Mode Suppression Ratio SMSR 30 dB
Transmitter OFF Output Power P
Off
-39
dBm
Optical Rise/Fall Time tr/tf 260 ps Note (3)
Total Jitter tJ 153 ps Note (4)
Optical Return Loss Tolerance ORLT 15 dB
Relative Intensity Noise RIN15OMA -115 dB/Hz
Optical Transmitter Reflectance -10 dB
Transmitter and Dispersion Penalty TDP 2.3 dB
Output Eye Mask
{X1,X2,Y1,Y2,Y3}
Compliant with IEEE 802.3ah
{0.22,0.375,0.20,0.20,0.30}
Note (5)
Note (1). Launched power (avg.) is power coupled into a single mode fiber with master connector.
B.O.L=Before of Life; E.O.L= End of Life
Note (2). The 20dB width for SLM Laser is taken as 6.07 times the RMS width
Note (3). These are unfiltered 20-80% values.
Note (4): Measure at 2
7
-1 NRZ PRBS pattern
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
3 Revision: S1
03/27/2007
www.deltaww.com
Note (5). Transmitter eye mask definition
4. Specification of Receiver
Parameter Symbol Min. Typ. Max. Unit Note
Input Optical Wavelength
λ
IN
1260 1310 1360 nm APD
Receiver Sensitivity PIN
-30
dBm Note (1)
Input Saturation Power (Overload) P
SAT
-8.5 dBm
Signal Detect -Assert Power PA - -30 dBm
Signal Detect -Deassert Power PD -44 dBm Note (2)
Signal Detect Hysteresis PA-PD 0.5 2 6 dB
Data Output Rise/Fall time tr/tf 260 ps Note (3)
Receiver Reflectance -12 dB
Receiver Threshold Setting Time T
RTS
400 ns
Guard Time GT 0 128 ns
Dynamic Range DR 21.5 dB
Note (4)
Note (1). Measured with Light source 1310nm, ER=9dB; BER =<10
-12
@PRBS=27-1 NRZ
This assurance should be met with asynchronous data flowing out of the optical transmitter of
the system under test. The output data pattern from the transmitter of the system under test is a
repetition of alternate 0/1 pattern as defined for this measurement.
Note (2). When SD deasserted, the data output is Low-level (fixed)
Note (3). These are 20%~80% values.
1
X1 X2
1- X2
1- X1
1+ Y 3
1
1- Y1
0.5
Y1
0
- Y2
N
ormalized Time
N
ormalized Amplitude
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
4 Revision: S1
03/27/2007
www.deltaww.com
Note (4). Burst mode receiver timing characteristic
5. Electrical Interface Characteristics
Parameter Symbol Min. Typ. Max. Unit Note
Transmitter
Total Supply Current ICC A mA Note (1)
Differential line input Impedance RIN 80 100 120 Ohm
Differential Data Input Swing VDT 400 1600 mV
p-p
Data Input Voltage- High VIH-VCC -1.165 -0.880 V
Data Input Voltage- Low VIL-VCC -1.810 -1.475 V
LVPECL
Transmitter Disable Input-High V
DISH
2 Vcc V
Transmitter Disable Input-Low V
DISL
0 0.8 V
LVTTL
Receiver
Total Supply Current ICC B mA Note (1)
Differential Data Output Swing VDR 400 1800 mV
p-p
Data Output Voltage-High VOH-VCC -1.085 -0.880 V
Data Output Voltage-Low VOL-VCC -1.830 -1.555 V
LVPECL
Signal Detect Output Voltage-High V
LOSH
2 Vcc+0.3 V
Signal Detect Output Voltage-Low V
LOSL
0 0.8 V
LVTTL
Note (1). A (TX)+ B (RX) = 350mA (Not include termination circuit)
R
eceiver Optical
I
nput Signal
Dynamic Range
Receiver Threshold Setting Time
BER
@
1210−
R
eceiver Electrical
Output Signal
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
5 Revision: S1
03/27/2007
www.deltaww.com
6. Pin Description
Tx/Rx Pin No. I/O Pin Name Description
1
VeeR
Receiver Ground
2
VccR
+3.3V Receiver Power Supply
3 O
SD Normal Optical Input indicated by logic “High”, and No Optical
Input indicated by logic “Low”.
4 O
RD(n)
Inverted Receiver Data Output
Rx
5 O
RD(p)
Non-Inverted Receiver Data Output
6
VccT
+3.3V Transmitter Power Supply
7
VeeT
Transmitter Ground
8 I
Tx_Dis
LVTTL Logic “High” or “Open” to Disable Transmitter, and Enable
Transmitter by Logic “Low”.
9 I
TD(p)
Non-Inverted Transmitter Data Input
Tx
10 I
TD(n)
Inverted Transmitter Data Input
MS
Mounting studs/ connect this pin to Chassis ground
Bottom View
MS
MS
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
6 Revision: S1
03/27/2007
www.deltaww.com
7. Recommended Interface Circuit
Transmitter
9. TD(p)
10. TD(n)
8. Tx_Dis
6. VccT
7. VeeT
Receiver
1. VeeR
5. RD(p)
4. RD(n)
3. SD
2. VccR
100nF
10uF 100nF
10uF
100nF
1uH
1uH
3.3V
Protocol IC
SerDes IC
Tx_Di s
SD
DELTA GEPON OLT Modu le
Z0=50o hm
Z0=50o hm
Z0=50ohm
Z0=50ohm
150ohm150ohm
100nF
100nF
130ohm
82ohm
130ohm
82ohm
3.3V
3.3V
82ohm
130ohm
3.3V
82ohm
130ohm
3.3V
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
7 Revision: S1
03/27/2007
www.deltaww.com
8. Outline Dimensions
Parameter Unit Description Note
Mechanical Dimensions mm 49.5x13.34x9.6
Connector Type - SC/UPC connector IEC-61754-4
Minimum Fiber Bending Radius mm 20
Maximum Fiber Contact Temperature ºC 85
Tensile Force on Pigtail Kg 1
Maximum Fiber Stress Allowance kpsi 200
Fiber length (L) mm 540 +/-20
Complies with FDA radiation
performance standards, 21 CFR Subchapter J.
Class 1 Laser Product
Week (52Weeks/Year) : 1月2日=01
OPEP-33-B4L3R
DELTA ELECTRONICS, INC.
8 Revision: S1
03/27/2007
www.deltaww.com
9. Regulatory Compliance
Feature Test M e t h o d Reference Performance
Human Body Model
(HBM)
MIL-STD-883E Method 3015.7
EIA-JESD22-A114
Electrostatic Discharge
(ESD) to the Electrical
Pins
Machine Model (MM) EIA-JESD22-A115
Contact Discharge IEC/EN 61000-4-2 Electrostatic Discharge
(ESD) to the Simplex
Receptacle
Air Discharge
IEC/EN 61000-4-2
Radio Frequency
Electromagnetic Field
Immunity
IEC/EN 61000-4-3
Electromagnetic
Interference (EMI)
FCC Part 15 Class B
EN 55022 Class B
(CISPR 22A)
(1) Satisfied with
electrical
characteristics of
product spec.
(2) No physical damage
Laser Eye Safety
FDA/CDRH
TUV
FDA 21CFR 1040.10, 1040.11
IEC/EN 60825-1
IEC/EN 60825-2
CDRH File # 0420993
TUV Certificate #
R50032471
Component Recognition
TUV
UL/CSA
IEC/EN 60950
UL 60950
UL File # E239394
Appendix A. Document Revision
Version No. Date Description
S0 2006-10-12 Preliminary datasheet
S1 2007-03-27 Update transmitter average launched power level.
Loading...