Delta MS450 Instruction Manual

INSTRUCTION MANUAL

ESPAÑOL: PÁGINA 23

To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,
please call

1-800-223-7278 (In Canada call 1-800-463-3582).

12" Compound Miter Saw

(Model MS450)

PART NO. A05721 - 07-22-04

Copyright © 2004 Delta Machinery

2

TABLE OF CONTENTS

Read and understand all warnings and operating instructions before using any tool or equipment. When
using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could result in serious injury and property
damage. There are certain applications for which tools and equipment are designed. Delta Machinery strongly
recommends that this product NOT be modified and/or used for any application other than for which it was designed.

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery
and we have advised you.

Online contact form at www.deltamachinery.com

Postal Mail: Technical Service Manager

Delta Machinery
4825 Highway 45 North
Jackson, TN 38305

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute
1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council
1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org
ANSI 01.1Safety Requirements for Woodworking Machines, and

the U.S. Department of Labor regulations www.osha.gov

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

SERVICE CENTER LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover

3

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR
SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

SAFETY GUIDELINES - DEFINITIONS

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER

CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

· lead from lead-based paints,

· crystalline silica from bricks and cement and other masonry products, and

· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.

CALIFORNIA PROPOSITION 65

4

1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION

MANUAL BEFORE OPERATING THE MACHINE.

Learning the machine’s application, limitations, and
specific hazards will greatly minimize the possibility of
accidents and injury.

2. WEAR EYE PROTECTION. ALWAYS USE SAFETY
GLASSES. Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses are NOT safety
glasses. USE CERTIFIED SAFETY EQUIPMENT. Eye
protection equipment should comply with ANSI Z87.1
standards, hearing equipment should comply with
ANSI S3.19 standards, and dust mask protection
should comply with MSHA/NIOSH certified respirator
standards. Splinters, air-borne debris, and dust can
cause irritation, injury, and/or illness.

3. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair
covering to contain long hair.

4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp or
wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to prevent
tripping or placing arms, hands, and fingers in danger.

5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing
accessories. Poorly maintained tools and machines can further
damage the tool or machine and/or cause injury.

6. CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, and any other conditions that may
affect its operation. A guard or any other part that is
damaged should be properly repaired or replaced.
Damaged parts can cause further damage to the
machine and/or injury.

7. KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.

8. KEEP CHILDREN AND VISITORS AWAY. Your shop is a
potentially dangerous environment. Children and visitors can
be injured.

9. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of a
power failure, move the switch to the “OFF” position.
An accidental start-up can cause injury.

10. USE THE GUARDS. Check to see that all guards are in
place, secured, and working correctly to prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high speed,
causing injury.

12. USE THE RIGHT MACHINE. Don’t force a machine or

an attachment to do a job for which it was not
designed. Damage to the machine and/or injury may
result.

13. USE RECOMMENDED ACCESSORIES. The use of

accessories and attachments not recommended by
Delta may cause damage to the machine or injury to the
user.

14. USE THE PROPER EXTENSION CORD. Make sure

your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage, resulting in loss of
power and overheating. See the Extension Cord Chart
for the correct size depending on the cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise to hold

the workpiece when practical. Loss of control of a
workpiece can cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION OF

THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE
SURFACE. Feeding it from the other direction will cause

the workpiece to be thrown out at high speed.

17. DON’T FORCE THE WORKPIECE ON THE MACHINE.

Damage to the machine and/or injury may result.

18. DON’T OVERREACH. Loss of balance can make you

fall into a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur if the

tool tips, or if you accidentally contact the cutting tool.

20. NEVER LEAVE THE MACHINE RUNNING UNATTENDED.
TURN THE POWER OFF. Don’t leave the machine until it
comes to a complete stop. A child or visitor could be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before installing
or removing accessories, before adjusting or changing
set-ups, or when making repairs. An accidental start-up
can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental start-up

of a machine by a child or visitor could cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR MEDICA­TION. A moment of inattention while operating power

tools may result in injury.

24. TAKE PRECAUTIONS AGAINST DUST INHALATION.
The dust generated by certain woods and wood
products can be injurious to your health. Always
operate machinery in well-ventilated areas, and provide
for proper dust removal. Use wood dust collection
systems whenever possible.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

5

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE UNTIL it is
assembled and installed according to the

instructions.

2. OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not familiar
with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommended
electrical connections.

4 MOUNT THE TOOL SECURELY to a stable

supporting surface prior to operation

5. DO NOT OPERATE SAW WITHOUT GUARDS IN
PLACE. Check to see that they are in place,
secured, and working correctly.

6. USE ONLY CROSSCUT SAW BLADES. Use only

zero-degree or negative hook angles when using
carbide-tipped blades. Do not use blades with deep
gullets. These can deflect and contact the guard.

7. USE ONLY BLADES OF THE CORRECT SIZE AND
TYPE specified for this tool.

8. USE A SHARP BLADE. Check blade to see if it runs
freely and is free from vibration.

9. INSPECT BLADE FOR CRACKS or other damage
prior to operation. Replace cracked or damaged
blade immediately.

10. CLEAN THE BLADE AND BLADE FLANGES prior
to operation. Check for any damage and tighten the
arbor nut securely.

11. USE ONLY BLADE FLANGES specified for this tool.

12. CLEAR THE AREA OF FLAMMABLE LIQUIDS
and/or gas prior to operation.

13. CLEAN THE MOTOR AIR SLOTS of chips and
sawdust.

14. TIGHTEN THE TABLE CLAMP HANDLE and any
other clamps prior to operation.

15. NEVER START THE TOOL with the workpiece
against the blade.

16. KEEP HANDS out of path of saw blade. Clamp all
workpieces that would require your hand to be in the
“Table Hazard Zone” (within the red lines).

17. ALLOW THE MOTOR to come to full speed prior to
starting cut.

18. NEVER REACH AROUND or behind the saw blade.

19. NEVER CUT FERROUS METALS or masonry.

ADDITIONAL SAFETY RULES FOR MITER SAWS

20. NEVER RECUT SMALL PIECES.

21. NEVER LOCK THE SWITCH in the “ON” position.

22. NEVER APPLY LUBRICANT to a running blade.

23. DO NOT PERFORM FREE-HAND OPERATIONS.

Hold the work firmly against the fence and table.
Use clamps to hold the work when possible.

24. PROPERLY SUPPORT LONG or wide workpieces.

25. AFTER COMPLETING CUT, release power switch

and wait for coasting blade to come to a complete
stop before returning saw to raised position. Make
sure saw cuttinghead returns freely to the full raised
position to ensure the lower blade guard fully
encloses the blade.

26. TURN OFF TOOL AND ALLOW THE BLADE TO
COME TO A COMPLETE STOP prior to cleaning
the blade area or removing debris in the path of the
blade. A coasting blade can be dangerous.

27. TURN OFF TOOL AND ALLOW BLADE TO COME
TO A COMPLETE STOP before removing or
securing workpiece, changing workpiece angle, or
changing the angle of the blade.

28. NEVER PERFORM LAYOUT, ASSEMBLY, or set-

up work on the table/work area when the machine is
running.

29. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs.

30. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.

31. ADDITIONAL INFORMATION regarding the safe

and proper operation of this tool, including a miter
saw safety video, is available from the Power Tool
Institute, 1300 Summer Avenue, Cleveland, OH
44115-2851. Information is also available from the
National Safety Council, 1121 Spring Lake Drive,
Itasca, IL 60143-3201. Please refer to the American
National Standards Institute ANSI 01.1 Safety
Requirements for Woodworking Machines and the
U.S. Department of Labor OSHA 1910.213
Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others

6

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3­prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

Fig. A Fig. B

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

2. Grounded, cord-connected machines intended for
use on a supply circuit having a nominal rating less
than 150 volts:

If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.

NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.

IN ALL CASES, MAKE CERTAIN THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment­grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.

Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment­grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.

Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.

Repair or replace damaged or worn cord immediately.

POWER CONNECTIONS

MOTOR SPECIFICATIONS

Your machine is wired for (see SPEC PLATE VOLTAGE), 60 HZ alternating current. Before connecting the machine to
the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.

7

FOREWORD

Delta ShopMaster Model MS450 is a high capacity 12" compound miter saw designed to cut wood and non-ferrous
metals. The unit can crosscut 8" x 2¼" and 7" x 3¼", miter at 45° both left and right 5¼" x 2¼", bevel at 45° left 6¼"
x 2¼" and 8" x 1¼", and compound 45° x 45°, 5¼" x 2 1/2" and 4¼" x 2¼". It has positive miter stops at 0°, 22.5°,

31.62°, and 45° both left and right, and bevel stops at 0° and 45° left.

NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THE CURRENT PRODUCTION
MODEL. ALL OTHER ILLUSTRATIONS CONTAINED IN THE MANUAL ARE REPRESENTATIVE ONLY
AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND ARE INTENDED
TO ILLUSTRATE TECHNIQUE ONLY.

FUNCTIONAL DESCRIPTION

EXTENSION CORDS

Use proper extension cords. Make sure
your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug
and matching receptacle which will accept the
machine’s plug. When using an extension cord, be sure
to use one heavy enough to carry the current of the
machine. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating. The
chart at right shows the correct gauge to use depending
on the cord length. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the
cord.

.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 120

up to

25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG
12-16 120 25-50 12 AWG
12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

8

UNPACKING

1. Carefully remove the machine from the carton. Retain all packing materials until you have inspected and
satisfactorily operated the machine.

DO NOT OPERATE THIS MACHINE UNTIL YOU READ AND UNDERSTAND THE ENTIRE
INSTRUCTION MANUAL.

2. Unassembled items are shown in Fig. 2 for identification and use in assembling the saw.

3. Place the machine on a firm, level surface with extra room for handling and proper support of the workpiece.

4. Familiarize yourself with all features and controls explained in this manual.

5. The machine is shipped with the cuttinghead locked in the down position and the table rotated to 45° left, as shown
in Fig. 3. To release the head and move it to the operating position, see “MOVING CUTTINGHEAD TO THE UP

POSITION” and “MOVING THE TABLE TO THE 0° CUT-OFF POSITION” in this manual (Fig. 5 & 7).

Fig. 2

1

2

4

3

5

B

Fig. 4

A

Fig. 3

6

7

8

9

10

11

12

13

14

CARTON CONTENTS

1 Work Clamp
2 Extension Bars (2)
3 3mm hex wrench
4 8mm/10mm wrench
5 Thumb screw (2)

6 Miter Handle
7 Thumb Screw for Sliding Fence
8 Sliding Fence
9 Set Screw M6 x 20mm
10 Stop Block
11 Wing Screw / Nuts (3)
12 Clamp Bracket (2)
13 Dust bag
14 Blade Wrench

9

Fig. 5

B

A

MOVING CUTTINGHEAD TO
THE UP POSITION

1. Push down slightly on the cuttinghead (B) Fig. 4
while pulling out the cuttinghead lockpin (A). Move
the cuttinghead (B) to the up position.

2. Fig. 5, illustrates the lockpin (A) pulled out and the
cuttinghead (B) in the up position.

MAKE SURE SAW CUTTINGHEAD
RETURNS FREELY TO THE FULL RAISED POSITION
TO ENSURE THE LOWER BLADE GUARD FULLY
ENCLOSES THE BLADE.

ASSEMBLY

ASSEMBLY TOOLS REQUIRED

ASSEMBLY TIME ESTIMATE

3mm hex wrench (supplied)

Assembly time for this product will be about 30 minutes to an hour.

ATTACHING THE MITER HANDLE

Thread the miter saw handle (A) Fig. 5A or (6) Fig. 2
into the hole in the table (B) Fig. 5A.

B

A

Fig. 5A

10

E

Fig. 7A

E

Fig. 7B

D

C

ATTACHING THE EXTENSION WINGS

This machine uses two table extension wings to help
support long or wide workpieces. To attach the wings:

1. Slide the stop block (A) Fig. 7A onto one wing (as
shown in Fig. 7A) and thread a wing screw (B) Fig. 7A
and (11) Fig. 2 into the hole on the side of the stop
block.

2. Tighten wing screw (B) Fig. 7A.

3. Insert extension wing rods (C) Fig. 7A into holes in
outer wall of saw as shown in Fig. 7A.

4. Thread wing screw (F) Fig. 7A into clamp bracket (E)
as shown. Place clamp bracket over hole (D) and
slide extension wing rod (C) through the clamp
bracket (E). Be sure other extenson wing rod (C) is
inserted through hole (G).

5. Tighten thumb screw (E) Fig. 7B.

NOTE: The right extension wing is installed the same
way.

B

A

MOVING TABLE TO THE 0° CUT-OFF
POSITION

1. Loosen locking knob (A) Fig. 6 by turning counter­clockwise. Depress lever (B) and rotate table (C) to
the 0° straight cut-off position, release lever (B), and
tighten locking knob (A).

2. Fig. 7 illustrates the table (C) in the 0° straight cut-off
position.

3. For proper operation and adjustment of the table,
refer to sections, “ROTATING TABLE FOR MITER

CUTTING”, and “ADJUSTING SLIDING FIT
BETWEEN MOVABLE TABLE AND BASE.”

Fig. 6

C

Fig. 7

B

A

C

G

F

11

ATTACHING THE FENCE SLIDE

1. Position the sliding fence (E) Fig. 7C, on top of saw
fence slide support(J). Install thumb screw (K) and
set screw (L) but do not tighten at this time.

2. Slide fence (E) on fence slide support (J) Fig. 7D.
Tighten set screw (L) with hex wrench (M) until it
contacts the fence slide support, then loosen one
turn. The purpose of this set screw is to prevent the
sliding fence from coming completely off the slide
support.

IF SET SCREW (L) IS LEFT TIGHT THE
SLIDING FENCE WILL NOT MOVE.

3. Slide fence to the desired position and tighten thumb
screw (K).

ATTACHING THE WORK CLAMP

Install work clamp assembly (F) Fig. 7E into desired
mounting hole (G). Assemble thumb screw (H) but do not
fully tighten at this time.

MAKE SURE THAT FENCE (M) Fig. 7F
AND WORK CLAMP (N) Fig. 7F ARE CLEAR OF
GUARD AND BLADE (L) Fig. 7F BEFORE OPERATING
SAW.

M

L

Fig. 7F

ATTACHING DUST BAG

Depress spring clips (A) Fig. 8, of dust bag (B) and clip
dust bag (B) over rib of dust chute.

Fig. 8

A

B

N

G

H

Fig. 7E

F

Fig. 7C

Fig. 7D

J

E

K

L

E

J

K

L

M

12

Fig. 11

B

12

Fig. 10

A

A

A

A

A

Fig. 9

FASTENING MACHINE TO SUPPORTING
SURFACE

Before operating your compound miter saw, firmly mount
it to a workbench or other supporting surface. Four
holes, (A) Fig. 9, are provided for fastening the saw to a
supporting surface.

When frequently moving the saw from place to place,
mount the saw to a 3/4” piece of plywood. The saw can
then be easily moved from place to place and the
plywood can be clamped to the supporting surface using
“C” clamps.

OPERATIONS

STARTING AND STOPPING MACHINE

To start the machine, depress switch trigger (A) Fig. 10.
To stop the machine, release the switch trigger.

This saw is equipped with an automatic electric blade
brake. As soon as the switch trigger (A) Fig. 10, is
released, the electric brake is activated and stops the
blade in seconds.

A TURNING SAW BLADE CAN BE
DANGEROUS. AFTER COMPLETING CUT, RELEASE
SWITCH TRIGGER (A) FIG. 10, TO ACTIVATE BLADE
BRAKE. KEEP CUTTINGHEAD DOWN UNTIL BLADE
HAS COME TO A COMPLETE STOP.

THE TORQUE DEVELOPED DURING
BRAKING MAY LOOSEN THE ARBOR SCREW. THE
ARBOR SCREW SHOULD BE CHECKED
PERIODICALLY AND TIGHTENED IF NECESSARY.

LOCKING SWITCH IN THE “OFF”
POSITION

IMPORTANT: When the miter saw is not in use, the

switch should be locked in the OFF position using a
padlock (B) Fig. 11, with a 3/16" diameter shackle to
prevent unauthorized use of the saw.

In the event of a power outage, always lock switch in
“OFF” position until the main power is restored.

OPERATIONAL CONTROLS AND ADJUSTMENTS

13

Fig. 12

A

B

Fig. 13

C

D

E

B

ROTATING TABLE FOR MITER
CUTTING

1. The compound miter saw will cut any angle from a
straight 0° cut to 47° right and left. Turn locking knob
(A) Fig. 12 counterclockwise, depress lock lever (B),
and rotate table to desired position.

2. The compound miter saw is equipped with positive
stops at the 0° cut-off position and at the 22.5°,

31.62°, and 45° left and right positions.

3. The center line, (C) Fig. 13, on the cursor indicates
the actual angle of cut. Each scale line (B) represents
1°. In effect, when the center line (C) is moved from
one line to the next on the scale, the angle of the cut
is changed by 1°.

4. The pointer is provided with two additional lines (D)
and (E), Fig. 13. This allows movement of the control
arm exactly 1/2°. For example, assume the center
line (C) is pointing to the 10° mark on the scale, as
indicated, and and the angle of cut is 1/2° to the
right. Move the control arm until the right line (E) lines
up with the next line on the scale. The angle of cut
will then be changed 1/2° to the right. If you change
the angle of cut 1/2° to the left, use the left line (D) in
the same manner.

ADJUSTING SLIDING FIT BETWEEN
MOVABLE TABLE AND BASE

1. DISCONNECT THE MACHINE
FROM THE POWER SOURCE.

2. To adjust the sliding fit between the movable table
and the base, turn nut (A) Fig. 14, clockwise to
increase the sliding fit (opposite to decrease the fit).
This adjustment should not be so tight that it restricts
the rotating movement of the table, or so loose that
it affects the accuracy of the saw.

Fig. 14

A

14

14

Fig. 15

C

B

Fig. 16

G

F

D

A

Fig. 17

A

A

ADJUSTING FENCE 90° TO BLADE

IMPORTANT: BEFORE MAKING THIS ADJUSTMENT,
SET THE BLADE AT 0° TO THE TABLE. SEE SECTION
“ADJUSTING 0° AND 45° BEVEL POSITIVE STOPS.”

1. DISCONNECT THE MACHINE
FROM THE POWER SOURCE.

2. Rotate the movable table so that the blade is 90° to
the fence and the positive stop is set for 0°.

3. Place one end of a framing square (A) Fig. 15 against
the front of the fence (B) and the other end against
the blade (C), with the blade locked in the down
position. The fence should be 90° to the blade.

4. If an adjustment is necessary, the fence, (B) Fig. 15,
can be adjusted by loosening four screws, two of
which are shown at (D), that attach the fence to the
base. Use the wrench supplied. Adjust the fence (B),
and tighten the four screws (D).

5. When the fence is 90° to the blade, adjust the cursor
(F) Fig. 16, so the pointer is aligned with the 0° mark
on the scale by loosening two screws, (G), adjusting
cursor (F) and tightening screws (G).

TABLE HAZARD ZONE

THE AREA INSIDE THE TWO RED
LINES (A) FIG. 17 ON THE TABLE IS DESIGNATED AS
A HAZARD ZONE. NEVER PLACE YOUR HANDS
INSIDE THIS AREA WHILE THE TOOL IS BEING
OPERATED. ALWAYS USE A CLAMP TO SECURE
SHORT WORKPIECES.

15

Fig. 20

TILTING CUTTINGHEAD FOR BEVEL
CUTTING

IMPORTANT: MOVE THE SLIDING FENCE TO THE
LEFT TO PROVIDE CLEARANCE FOR THE
BLADE AND GUARD. THE DEGREES OF TILT
DETERMINES HOW FAR TO MOVE THE SLIDING
FENCE. REFER TO THE SECTION “ADJUSTING
SLIDING FENCE.”

1. DISCONNECT THE MACHINE
FROM THE POWER SOURCE.

2. The cuttinghead of your compound miter saw can be
tilted to cut any bevel angle from a 90° straight cut­off to a 45° left bevel angle. Loosen bevel lock handle
(A) Fig. 18, tilt cuttinghead (B) to the desired angle,
and tightening lock handle (A).

3. Positive stops are provided to rapidly position the
saw blade at 90° and 45° to the table. Refer to the
section of this manual titled “Adjusting 0° and 45°
bevel positive stops.” The bevel angle of the cutting
arm is determined by the position of the pointer (C)
Fig. 19, on scale (D).

4. In addition, a marked indicator (M) is provided on the
bevel scale (33.9°) for cutting crown moulding. Refer
to the “CUTTING CROWN MOULDING” section of
this manual.

ADJUSTING SLIDING FENCE AND
WORK CLAMP

The high sliding fence (E) Fig. 20, provides support for
extra large workpieces used with your saw and should
always be set as close as possible to the saw blade.
When miter cutting (set blade 90° to the table and at an
angle to the right or left), the fence should be set all the
way toward the blade, (Fig. 20). When bevel cutting,
however (blade tilted at an angle to the table), the fence
(M) Fig. 21, and the work clamp (N) Fig. 21 should be
moved away from the blade to allow for proper clearance
for the saw blade and guard (L) Fig. 21.

To reposition the fence, loosen the thumb screw (K) Fig.
20, and slide the fence to the desired location and tighten
the thumb screw (K). To reposition the work clamp, loosen
the thumb screw (P) Fig. 21, and reposition to the work to
clear the blade and guard and tighten the thumb screw
(P).

MAKE SURE THAT FENCE (M) Fig. 21
AND WORK CLAMP (N) Fig. 21 ARE CLEAR OF
GUARD AND BLADE (L) Fig. 21 BEFORE OPERATING
SAW.

Fig. 18

A

B

Fig. 19

D

C
M

J

K

E

Fig. 21

M

L

N

P

16

16

Fig. 24

H

C

B

Fig. 25

A

Fig. 26

F

E

Fig. 23

A

ADJUSTING 0° AND 45° BEVEL
POSITIVE STOPS

1. DISCONNECT THE MACHINE
FROM THE POWER SOURCE.

2. Adjust saw so that both bevel and miter pointers are
set at 0°. Tighten bevel lock handle and lock
cuttinghead in down position.

3. Place one end of a square (A) Fig. 23 on the table and
the other end against the blade. The blade should be
set at 90° to the table.

4. If an adjustment is necessary, loosen bevel lock
handle (H) Fig. 24. Loosen locknut (B) and turn
adjusting screw (C), with wrenches provided, until
blade is 90° to the table. Tighten locknut (B) and
bevel lock handle (H).

5. When the blade is 90° to the table, adjust the pointer
to line up with the 0° mark on the bevel scale.

6. Loosen bevel lock handle (H) Fig. 24, and move
cuttinghead all the way to the left bevel position and
tighten bevel lock handle.

7. Use a square (A) Fig. 25, to see if the blade is at 45°
to the table.

8. If an adjustment is necessary, loosen the bevel lock
handle. Loosen the locknut (E) Fig. 26, and turn the
adjusting screw (F), with wrenches provided, until the
blade is 45° to the table. Tighten locknut (E) and
bevel lock handle.

9. These positive stops enable the operator to rapidly
position the blade at the most common bevel angles
to the table, 90° and 45°.

ADJUSTING SLIDING FIT BETWEEN
TRUNNION AND BEVEL BRACKET

After a long period of time, it may become necessary to
adjust the sliding fit between the trunnion and the bevel
bracket by tightening the adjusting nut (C), Fig. 27, located
underneath the bevel lock knob (B) Fig. 27.

Correct adjustment provides for a good snug sliding fit
between these two parts. This adjustment should not be
so tight that it restricts the tilting movement of the
trunnion when bevel cutting, or so loose that it affects the
accuracy of the saw cut.

17

Fig. 27

C

B

A

C

D

Fig. 28

Fig. 29

A

B

C

ADJUSTING THE TENSION OF
CUTTINGHEAD RETURN SPRING

The tension of the cuttinghead return spring has been
adjusted at the factory in order that the cuttinghead
returns to the up position after a cut has been made. To
adjust the spring tension, turn adjusting screw (A) Fig. 28,
clockwise to increase or counterclockwise to decrease the
spring tension.

MAKE SURE SAW CUTTINGHEAD
RETURNS FREELY TO THE FULL RAISED POSITION
TO ENSURE THE LOWER BLADE GUARD FULLY
ENCLOSES THE BLADE.

ADJUSTING SLIDING FIT BETWEEN
CUTTINGHEAD ARM AND TRUNNION

After a long period of time, an adjustment of the sliding
fit between the cuttinghead arm (B) Fig. 28, and the
trunnion (C) may be necessary. To adjust, tighten nut (D).
Correct adjustment is a good snug sliding fit between
these two parts. This adjustment should not be so tight
that it restricts the sliding movement of the cuttinghead
arm (B) or so loose that it affects the accuracy of the saw
cut.

ADJUSTING DOWNWARD TRAVEL OF
SAW BLADE

1. DISCONNECT THE MACHINE

FROM THE POWER SOURCE.

2. The downward travel of the saw blade can be limited

to prevent the saw blade from contacting any metal
surfaces of the machine. This adjustment is made by
loosening locknut (A) Fig. 29, and turning adjusting
screw (B) in or out until other end of screw (B)
contacts stop (C) at the full downward travel of the
saw blade.

3. Lower the blade as far as possible. Rotate the blade

by hand to make certain the teeth do not contact any
metal surfaces and adjust if necessary. After
adjustment is completed, tighten locknut (A) Fig. 29.

B

Fig. 30

A

B

ADJUSTING LOWER BLADE GUARD

After an extended period of use the movable lower blade
guard (A) Fig. 30, may not operate smoothly when the
cuttinghead is lowered. This can be corrected by
adjusting nut (B) until the lower blade guard (A) moves
freely.

DO NOT OVERTIGHTEN THE NUT AS

THIS COULD IMPAIR GUARD MOVEMENT.

18

AUXILIARY WOOD FENCE

When performing multiple or repetitive
cut-off operations that result in small cut-off pieces (one
inch or less), the saw blade can catch the cut-off pieces
and project them out of the machine or into the blade
guard and housing, possibly causing damage and/or
injury. In order to limit the possibility of personal injury or
blade guard damage, an auxiliary wood fence can be
mounted to your saw as follows:

Holes are provided in the fence to attach an auxiliary

B

A

Fig. 31

TYPICAL USAGE AND HELPFUL HINTS

1. Before cutting, make certain the cutting arm and
table area are at their correct settings and firmly
locked in place.

2. Before cutting, determine that the workpiece is the
right size for the saw.

3. Place the workpiece on the table and hold or clamp
it firmly against the fence.

4. If the size of the workpiece causes your hand to be
inside the table hazard zone (see section “TABLE
HAZARD ZONE” SEE FIG. 17), use a clamp to
secure the workpiece.

5. For best results, cut at a slow, even cutting rate.

6. Never attempt any freehand cutting (wood that is not
held firmly against the fence and table).

ADJUSTING EXTENSION WINGS
AND STOP BLOCK

The stop block can be used for cuting off several pieces
to the same length. The edge of the workpiece (A) Fig.
30B should rest against the stop block as shown. To
adjust the stop block to the proper measurement, loosen
the wing screw (B) Fig. 30A, reset the stop block in the
desired location and tighten the wing screw.

If the stop block (A) Fig. 30C is not needed, it can be
moved out of the way so both extension wings can be
used to support a long piece. To move the block, loosen
the wing screw (B) Fig. 30C and move it out of the way
as shown.

To adjust the extension wings (C) Fig. 30A to
accommodate long workpieces, loosen the wing screw
(D), reset the extension wing and tighten the wing screw.
The extension wing rods should not be pulled out so far
that they can’t be clamped by the wing nut and bracket
assembly (D).

Fig. 30A

A

B

C

D

MACHINE USE

Fig. 30B

Fig. 30C

B

A

A

19

Fig. 34

Fig. 35

CORRECT

INCORRECT

CUTTING ALUMINUM

Aluminum extrusions (aluminum screens and storm
windows) can easily be cut with your miter saw. When
cutting aluminum extrusions, or other sections that can
be cut with a saw blade and are within the capacity of the
machine, position the material so the blade is cutting
through the smallest cross-section, as shown in Fig. 32.
The wrong way to cut aluminum angles is illustrated in
Fig. 33. Be sure to apply a stick wax (similar to Johnson’s
stick wax #140) to the blade before cutting any aluminum
stock. This stick wax is available at most industrial mill
supply houses. The stick wax provides proper lubrication
and keeps chips from adhering to the blade.

NEVER APPLY LUBRICANT TO THE

BLADE WHILE THE BLADE IS RUNNING.

CUTTING BOWED MATERIAL

1. First check to see if the material is bowed. If it is,
make sure the material is positioned on the table as
shown in Fig. 34.

2. If the material is positioned the wrong way, as shown
in Fig. 35, the workpiece will pinch the blade near the
completion of the cut.

Fig. 32

Fig. 33

FENCE

FENCE

BLADE

BLADE

CORRECT

INCORRECT

Fig. 36

C

B

A

C

WORK SUPPORT EXTENSIONS

For support when cutting long pieces, construct a work
support extension. Fig. 36 illustrates the miter saw
mounted on two standard 2 x 4’s (A). Fasten the four
mounting legs (two of which are shown at (B) Fig. 36 to
the 2 x 4’s, using four screws (not supplied) through the
four holes in the mounting legs. The length of the 2 x 4’s
(A) can vary, depending on the workpiece.

NOTE: MAKE SURE THAT THE TOP OF THE
SUPPORT 2 X 4’S (C) ARE LEVEL WITH THE MITER
SAW TABLE.

This is critical because the distance from the top of the 2
x 4’s (A) to the miter saw table varies from saw to saw. In
most cases, standard 2 x 4’s (C) can used. If these are
too high, cut them to fit. If the 2 x 4’s are too low, use 2
x 6’s. If these are high, cut them to the correct height.

fence (A) and (B) Fig. 31. This auxiliary fence is
constructed of straight wood approximately 1/2” thick by
3” high by 16 inches long as shown at (B); and 1/2” thick
by 5” high by 17” long (A) Fig. 31.

NOTE: The auxiliary fence (A) is used only with the saw
blade in the 0° bevel position (90°) to the table. The
auxiliary fence must be removed for all bevel cuts (blade
tilted).

20

D

C

Fig. 38

Fig. 39

2

1

Fig. 40

1

2

D

B

A

C

Fig. 37

B

A

CUTTING CROWN MOULDING

One of the many features of the saw is the ease of cutting
crown moulding. The following is an example of cutting
both inside and outside corners on 52°/38° wall angle
crown moulding.

1. Move the table to the 31.62° right miter position and

lock the table in position. NOTE: A positive stop is
provided to find this angle quickly.

2. Tilt the saw blade to the 33.86° left bevel position and

tighten bevel lock handle. NOTE: A triangle indicator
is provided on the bevel scale to find this angle
quickly.

3. Place the crown moulding on the table with the

CEILING EDGE of the moulding against the fence,
and make the cut, as shown in Fig. 37.

NOTE: The piece of crown moulding used for the outside

corner will always be on the right hand side of the
blade, as shown at (A) Fig. 37. The piece of crown
moulding used for the inside corner will always be on
the left hand side of the blade, as shown at (B) Fig.

37.

4. To make the matching halves of the inside and
outside corners, rotate the table to the 31.62° left
miter position.

NOTE: A positive stop is provided to find this angle

quickly. The saw blade is already tilted to the 33.86°
bevel position from the previous cut.

5. Place the crown moulding on the table with the WALL
EDGE of the crown moulding against the fence and
make the cut. Again, the piece of crown moulding
used for the outside corner will always be on the right
side of the blade, as shown at (C) Fig. 38. The piece
of crown moulding used for the inside corner will
always be on the left side of the blade, as shown at
(D) Fig. 38.

6. Fig. 39 illustrates the two outside corner pieces; (1)
being the piece cut at (A) Fig. 37 and (2) being the
piece cut at (C) Fig. 38.

7. Fig. 40 illustrates the two inside corner pieces; (1)
being the piece cut at (B) Fig. 37, and (2) being the
piece cut at (D) Fig. 38.

45-45 CROWN MOULDING

NOTE: If you are cutting crown moulding that is 45°-45°,

follow the same procedure above, with the exception
that the bevel position will always be at 30° and the miter
position will be 35-1/4° to the right or left.

OTHER ANGLES

NOTE: The above instructions are assuming the angle

between the walls is 90°. If you need help cutting crown
moulding for walls set at angles other than 90°, see the
instruction sheet “CUTTING CROWN MOULDING” on
the Delta Machinery web site at
www.deltamachinery.com.

21

Fig. 41

A

Fig. 43

F

Fig. 45

B

C

Fig. 44

A

CHANGING THE BLADE

USE ONLY CROSS-CUTTING SAW
BLADES. DO NOT USE BLADES WITH DEEP
GULLETS AS THEY CAN DEFLECT AND CONTACT
GUARD

1. Use only 12" diameter blades with 1" arbor holes
that are rated for 4000 RPM or higher.

2. DISCONNECT THE MACHINE

FROM THE POWER SOURCE.

3. Loosen screw (A) Fig. 41, with wrench provided.

4. Rotate arbor cover (C) Fig. 42, and lower guard (D)
Fig. 43, to the rear, exposing arbor screw (E).

5. Remove arbor screw (E) Fig. 42, by turning screw
clockwise with wrench supplied), while at the same
time, pressing in on arbor lock (F) Fig. 43, to keep the
arbor from turning. Remove outside blade flange (G)
Fig. 42, and saw blade (H) Fig. 42. DO NOT

REMOVE INSIDE BLADE FLANGE.

6. Attach the new saw blade MAKING CERTAIN
TEETH OF SAW BLADE ARE POINTING DOWN AT
THE FRONT, and attach outside blade flange (G)

Fig. 42. Check to see that the flats on outside blade
flange are engaged with flats on arbor shaft.

7. Thread arbor screw (E) Fig. 42, into saw arbor by
turning screw (E) counterclockwise as far as possible
by hand. Then tighten arbor screw (E) with wrench
supplied while at the same time pressing in on arbor
lock (F) Fig. 43, to keep arbor from turning.

8. Rotate arbor cover (C) Fig. 42, and lower guard (D) to
the front and tighten screw (A) that was loosened in

STEP 3.

MAKE SURE BOTH ARBOR SCREW
AND ARBOR COVER SCREW ARE SECURELY
FASTENED BEFORE OPERATING THE SAW.

BRUSH INSPECTION AND
REPLACEMENT

DISCONNECT THE MACHINE FROM

THE POWER SOURCE.

Brush life varies, depends on the load on the motor.
Check the brushes after the first 50 hours of use of a new
machine, or after a new set of brushes has been
installed.

After the first check, examine them after about 10 hours
of use, until replacement is necessary.

The brush holders (A) Fig. 44, are located on the motor
housing opposite each other. Fig. 45, illustrates one of
the brushes removed for inspection. When the carbon on
either brush (B) is worn to 3/16" in length, or if either
spring or shunt wire (C) is burned or damaged in any way,
replace both brushes. If the brushes are found
serviceable after removing, reinstall them in the same
position.

MAINTENANCE

Fig. 42

E

G

C

H

D

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call
the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

22

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER use
solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

CAUTION: WEAR SAFETY GLASSES WHILE USING COMPRESSED AIR.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact with the outlet.
Also, check for blown fuses or open circuit breakers in the line.

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or
for the name of your nearest supplier.

Since accessories other than those offered by Delta have not been tested
with this product, use of such accessories could be hazardous. For safest operation, only
Delta recommended accessories should be used with this product.

ACCESSORIES

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

SERVICE

WARRANTY

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE

•

DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,

Contractor’s Saw II™, Delta

®

, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,

Grip Vac™, Homecraft

®

, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,

MORTEN™, NETWORK™, OMNIJIG

®

, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-

CABLE

®

PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),

QUICKSET™, QUICKSET II

®

, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW

BOSS

®

, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber

Company

®

&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,

TORQBUSTER

®

, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,

Univise

®

, Versa-Feeder®, VERSA-PLANE®, WHISPER SERIES®, WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE

• DELTA)

Parts and Repair Service for Porter-Cable •Delta Machinery are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

•

Delta)

Authorized Service Stations are located in many large cities. Telephone [phone] or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable

·

Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized

Service Center, or Porter-Cable

·

Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will

be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable

·

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro

de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable

·

Delta más cercano.

ARIZONA

Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: [phone]
Fax: [phone]

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: [phone]
Fax: [phone]

San Diego 92111
7638 Clairemnot Blvd.
Phone: [phone]
Fax: [phone]

San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: [phone]
Fax: [phone]

COLORADO

Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: [phone]
Fax: [phone]

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: [phone]
Fax: [phone]

Tampa 33609
4538 W. Kennedy Boulevard
Phone: [phone]
Fax: [phone]

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: [phone]
Fax: [phone]

ILLINOIS

Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: [phone]
Fax: [phone]

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: [phone]
Fax: [phone]

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: [phone]
Fax: [phone]

MASSACHUSETTS

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: [phone]
Fax: [phone]

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: [phone]
Fax: [phone]

MINNESOTA

Minneapolis 55429
5522 Lakeland Avenue North
Phone: [phone]
Fax: [phone]

MISSOURI

North Kansas City 64116
1141 Swift Avenue
Phone: [phone]
Fax: [phone]

St. Louis 63119
7574 Watson Road
Phone: [phone]
Fax: [phone]

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: [phone]
Fax: [phone]

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: [phone]
Fax: [phone]

OHIO

Columbus 43214
4560 Indianola Avenue
Phone: [phone]
Fax: [phone]

Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: [phone]
Fax: [phone]

OREGON

Portland 97230
4916 NE 122 nd Ave.
Phone: [phone]
Fax: [phone]

PENNSYLVANIA

Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: [phone]
Fax: [phone]

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: [phone]
Fax: [phone]

Houston 77043
4321 Sam Houston Parkway,
West
Suite 180
Phone: [phone]
Fax: [phone]

WASHINGTON

Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: [phone]
Fax: [phone]

PC-0704-149

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: [phone]
Fax: [phone]

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: [phone]
Fax: [phone]

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: [phone]
Fax: [phone]

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: [phone]
Fax: [phone]

QUÉBEC

1515 ave.
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: [phone]
Fax: [phone]

1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: [phone]
Fax: [phone]