INSTRUCTION MANUAL
10" Compound
Power Miter Saw
(Model MS250)
PART NO. 905573 - 07-03-03
Copyright © 2003 Delta Machinery
ESPAÑOL: PÁGINA 23
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Product covered by
U.S. Patent No.
5,347,902
5,235,889
2
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols to the right. Please read the manual and pay attention to these sections.
SAFETY GUIDELINES - DEFINITIONS
SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility. For additional information please visit our website www.deltamachinery.com.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this
machine not be modified and/or used for any application other than that for which it was designed. If you have any
questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine
if it can or should be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)
3
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION MANUAL BEFORE OPERATING THE
MACHINE. Learning the machine’s application,
limitations, and specific hazards will greatly
minimize the possibility of accidents and injury.
2. USE CERTIFIED SAFETY EQUIPMENT. Eye
protection equipment should comply with ANSI
Z87.1 standards, hearing equipment should
comply with ANSI S3.19 standards, and dust mask
protection should comply with MSHA/NIOSH
certified respirator standards. Splinters, air-borne
debris, and dust can cause irritation, injury, and/or
illness.
3. DRESS PROPERLY. Do not wear tie, gloves, or
loose clothing. Remove watch, rings, and other
jewelry. Roll up your sleeves. Clothing or jewelry
caught in moving parts can cause injury.
4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp
or wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to
prevent tripping or placing arms, hands, and
fingers in danger.
5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating
and changing accessories. Poorly maintained tools and
machines can further damage the tool or machine and/or
cause injury.
6. CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, and any other conditions
that may affect its operation. A guard or any other
part that is damaged should be properly repaired
or replaced. Damaged parts can cause further
damage to the machine and/or injury.
7. KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
8. KEEP CHILDREN AND VISITORS AWAY. Your shop is
a potentially dangerous environment. Children and visitors
can be injured.
9. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of
a power failure, move the switch to the “OFF”
position. An accidental start-up can cause injury.
10. USE THE GUARDS. Check to see that all guards
are in place, secured, and working correctly to
prevent injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high
speed, causing injury.
12. USE THE RIGHT MACHINE. Don’t force a
machine or an attachment to do a job for which it
was not designed. Damage to the machine and/or
injury may result.
13. USE RECOMMENDED ACCESSORIES. The use
of accessories and attachments not recommended by Delta may cause damage to the
machine or injury to the user.
14. USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See the Extension Cord Chart for the correct size
depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
15. SECURE THE WORKPIECE. Use clamps or a vise to
hold the workpiece when practical. Loss of control
of a workpiece can cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION
OF THE ROTATION OF THE BLADE, CUTTER, OR
ABRASIVE SURFACE. Feeding it from the other
direction will cause the workpiece to be thrown out
at high speed.
17. DON’T FORCE THE WORKPIECE ON THE
MACHINE. Damage to the machine and/or injury
may result.
18. DON’T OVERREACH. Loss of balance can make
you fall into a working machine, causing injury.
19. NEVER STAND ON THE MACHINE. Injury could occur if
the tool tips, or if you accidentally contact the cutting tool.
20. NEVER LEAVE THE MACHINE RUNNING UNATTEN-
DED. TURN THE POWER OFF. Don’t leave the machine
until it comes to a complete stop. A child or visitor could
be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs. An
accidental start-up can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental
start-up of a machine by a child or visitor could
cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while
operating power tools may result in injury.
24. THE DUST GENERATED by certain woods and
wood products can be injurious to your health.
Always operate machinery in well-ventilated areas,
and provide for proper dust removal. Use wood
dust collection systems whenever possible.
4
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
ADDITIONAL SAFETY RULES
FOR MITER SAWS
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
1. DO NOT OPERATE THIS MACHINE until it is
completely assembled and installed according to the
instructions. A machine incorrectly assembled can
cause serious injury.
2. OBTAIN ADVICE from your supervisor, instructor, or
another qualified person if you are not thoroughly
familiar with the operation of this machine. Knowledge
is safety.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections to prevent shock or
electrocution.
4. SECURE THE MACHINE TO A SUPPORTING SURFACE.
Vibration can possibly cause the machine to slide,
walk, or tip over, causing serious injury.
5. USE ONLY CROSSCUT SAW BLADES. Use only
zero-degree or negative hook angles when using
carbide-tipped blades. Do not use blades with deep
gullets. These can deflect and contact the guard, and
can cause damage to the machine and/or serious
injury.
6. USE ONLY BLADES OF THE CORRECT SIZE AND
TYPE specified for this tool to prevent damage to the
machine and/or serious injury.
7. USE A SHARP BLADE. Check the blade to see if it
runs true and is free from vibration. A dull blade or a
vibrating blade can cause damage to the machine
and/or serious injury.
8. INSPECT BLADE FOR CRACKS or other damage
prior to operation. A cracked or damaged blade can
come apart and pieces can be thrown at high speeds,
causing serious injury. Replace cracked or damaged
blades immediately.
9. CLEAN THE BLADE AND BLADE FLANGES prior to
operation. Cleaning the blade and flanges allows you
to check for any damage to the blade or flanges. A
cracked or damaged blade or flange can come apart
and pieces can be thrown at high speeds, causing
serious injury.
10. USE ONLY BLADE FLANGES specified for this tool
to prevent damage to the machine and/or serious
injury.
11. CLEAR THE AREA OF FLAMMABLE LIQUIDS
and/or gas prior to operation. Sparks can occur that
would ignite the liquids and cause a fire or an
explosion.
12. CLEAN THE MOTOR AIR SLOTS of chips and
sawdust. Clogged motor air slots can cause the
machine to overheat, damaging the machine and
possibly causing a short which could cause serious
injury.
13. TIGHTEN THE TABLE CLAMP HANDLE and any
other clamps prior to operation. Loose clamps can
cause parts or the workpiece to be thrown at high
speeds.
14. NEVER START THE TOOL with the blade against the
workpiece. The workpiece can be thrown, causing
serious injury.
15. KEEP ARMS, HANDS, AND FINGERS away from the
blade to prevent severe cuts. Clamp all workpieces
that would cause your hand to be in the “Table
Hazard Zone” (within the red lines).
16. WHEN CUTTING WITH A COMPOUND SLIDING
MITER SAW, PUSH THE SAW FORWARD (AWAY
FROM YOU) and toward the fence. Pulling the saw
toward you can cause the saw to kick upward and
toward you.
17. WHEN USING A SLIDING MITER SAW AS A REGULAR
MITER SAW, LOCK THE SLIDE MECHANISM IN PLACE.
If the slide mechanism is not locked, the saw can kick
back toward you.
18. ALLOW THE MOTOR TO COME TO FULL SPEED
prior to starting cut. Starting the cut too soon can
cause damage to the machine or blade and/or
serious injury.
19. NEVER REACH AROUND or behind the saw blade.
A moving blade can cause serious injury.
20. NEVER CUT FERROUS METALS or masonry. Either
of these can cause the carbide tips to fly off the blade
at high speeds causing serious injury.
21. NEVER CUT SMALL PIECES. Cutting small pieces
can cause your hand to move into the blade, resulting
in serious injury.
22. NEVER LOCK THE SWITCH in the “ON” position.
Setting up the next cut could cause your hand to
move into the blade, resulting in severe injury.
23. NEVER APPLY LUBRICANT to a running blade.
Applying lubricant could cause your hand to move
into the blade, resulting in serious injury.
24. DO NOT PERFORM FREE-HAND OPERATIONS.
Hold the work firmly against the fence and table.
Free-hand operations on a miter saw could cause the
workpiece to be thrown at high speeds, causing
serious injury. Use clamps to hold the work when
possible.
25. AFTER COMPLETING CUT, release power switch
and wait for coasting blade to come to a complete
stop before returning saw to raised position. A
moving blade can cause serious injury.
26. TURN OFF THE MACHINE and allow the blade to
come to a complete stop prior to cleaning the blade
area or removing debris in the path of the blade. A
moving blade can cause serious injury.
27. TURN OFF MACHINE and allow the blade to come
to a complete stop before removing or securing
workpiece, changing workpiece angle, or changing
the angle of the blade. A moving blade can cause
serious injury.
28. PROPERLY SUPPORT LONG OR WIDE WORK-
PIECES. Loss of control of the workpiece can cause injury.
29. NEVER PERFORM LAYOUT, ASSEMBLY, OR SET-UP
WORK on the table/work area when the machine is
running. A sudden slip could cause a hand to move
into the blade. Severe injury can result.
30. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to prevent
unauthorized use. Someone else might accidentally
start the machine and cause injury to themselves.
32. BEFORE OPERATING THE SAW, check and
securely lock the bevel, miter, and sliding fence
adjustments.
33. ADDITIONAL INFORMATION regarding the safe and
proper operation of power tools (i.e. a safety video) is
available from the Power Tool Institute, 1300 Sumner
Avenue, Cleveland, OH 44115-2851
(www.powertoolinstitute.com). Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please refer
to the American National Standards Institute ANSI
01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor
regulations.
5
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the
same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
Fig. A Fig. B
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
GROUNDED OUTLET BOX
GROUNDING
MEANS
ADAPTER
2. Grounded, cord-connected machines intended for use
on a supply circuit having a nominal rating less than 150
volts:
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
IN ALL CASES, MAKE CERTAIN THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipmentgrounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.
Repair or replace damaged or worn cord immediately.
POWER CONNECTIONS
MOTOR SPECIFICATIONS
Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
6
EXTENSION CORDS
FOREWORD
Delta ShopMaster Model MS250 is a 10" Compound Power Miter Saw designed to cut wood, plastic, and aluminum.
Compound angle and bevel cutting are easy and accurate. It can crosscut up to 5-3/4" x 2-3/8", miter at 45 both left and
right 4-1/8" x 2-3/8", bevel at 45 left 5-7/8" x 1-9/16", and compound 45 x 45, 4-1/8" x 1-9/16". It has positive miter at
0, 22.5, 31.6, and 45 degrees both left and right, and bevel stops at 0 and 45 degrees adjustable.
FUNCTIONAL DESCRIPTION
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT
PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE
ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR
ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1, shows the correct
gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
Fig. D-1
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Total Length Gauge of
Rating Volts of Cord in Feet Extension Cord
0-6 120
up to
25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG
6-10 120
up to
25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG
10-12 120
up to
25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG
12-16 120
up to
25 14 AWG
12-16 120 25-50 12 AWG
12-16 120
GREATER THAN 50 FEET NOT RECOMMENDED
7
CARTON CONTENTS
Fig. 1
Remove the miter saw and all loose items from the carton.
DO NOT LIFT THE MITER SAW BY THE SWITCH HANDLE. THIS ACTION CAN CAUSE
MISALIGNMENT. ALWAYS LIFT THE MACHINE BY THE BASE OR THE CARRYING HANDLE.
1. Miter Saw Arm
2. Miter Saw Base
3. Dust Bag
4. 1/2" Blade Wrench
5. 5mm Hex Wrench
6. Table Lock Handle
7. Bevel Pointer
8. M5x.8x10mm Pan Head Screw with a M5.3 Flat Washer
1
2
3
4
5
6
7
8
8
ASSEMBLY
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL
THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE
INSTRUCTION MANUAL.
ATTACHING MITER SAW
ARM TO BASE
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Align the bevel lock handle screw (A) Fig. 2, on the
miter saw arm with the bevel hub (B) on the base.
2. Thread the bevel lock handle screw (A) Fig. 2, into the
bevel hub (B) by turning the bevel handle knob (K) Fig. 2A
and tighten securely.
Fig. 2
ATTACHING BEVEL
POINTER
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Loosen the bevel lock handle (A) Fig. 2A, and tilt the
miter saw arm to the 45 degree position as shown.
2. Align the hole in the bevel pointer (C) Fig, 2A, with the
hole (D) in the back of the base.
3. Insert the M5x.8x10mm pan head screw with washer
(B) through the hole in the bevel pointer (C) Fig. 2A, and
thread the screw into the hole (D) in the back of the base
and tighten securely. NOTE: TO ADJUST THE
POINTER SEE SECTION “ADJUSTING 90 AND 45
DEGREE BEVEL STOPS”.
Fig. 2A
ATTACHING TABLE LOCK
HANDLE
Thread table lock handle (A) Fig. 3 into the threaded hole
(B) of the arm bracket.
Fig. 3
Fig. 4
ROTATING TABLE TO 90
DEGREE POSITION
1. Loosen table lock handle (A) Fig. 4 one or two turns
and depress index lever (B) to release 45 degree positive
stop.
B
A
A
B
A
B
K
C
D
B
K
9
2. Rotate table to the left until index stop engages with
the 90 degree positive stop (Fig. 5). Tighten table lock
handle (A).
Fig. 5
MOVING CUTTINGHEAD TO
THE UP POSITION
1. Push down on switch handle (A) Fig. 6, and pull out
cuttinghead lock knob (B).
2. Move the cuttinghead (C) to the up position (Fig. 7).
Fig. 6
Fig. 7
ATTACHING
DUST BAG
Attach dust bag (A) Fig. 8 to the dust spout (B) making
sure the wire ring (C) is engaged with the ridge in the
spout.
Fig. 8
A
A
B
C
B
C
A
10
FASTENING MACHINE TO
SUPPORTING SURFACE
Before operating your compound miter saw, make sure
it is firmly mounted to a sturdy workbench or other
supporting surface. Four holes are provided, two of which
are shown at (A) Fig. 9.
When frequently moving the saw from place to place, we
suggest that the saw be mounted to a 3/4″ piece of
plywood. The tool can then be easily moved from place
to place and the plywood clamped to the supporting
surface using “C” clamps.
Fig. 9
OPERATING CONTROLS AND ADJUSTMENTS
TABLE HAZARD AREA
THE AREA INSIDE THE TWO RED
LINES (A) FIG. 10 ON THE TABLE IS DESIGNATED AS
A HAZARD ZONE. NEVER PLACE YOUR HANDS
INSIDE THIS AREA WHILE THE MACHINE IS
RUNNING.
Fig. 10
1. An optional work clamp (A) Fig. 11 is available. Use
this accessory clamp, especially with short workpieces.
Never allow your hands to be in the “Hazard Zone”.
2. Two holes (B) Fig. 10 are provided in the base of the
miter saw, enabling you to use the clamp (A) Fig. 11 on
either the right or left hand side of the saw blade.
KEEP HANDS OUT OF PATH OF SAW
BLADE. IF NECESSARY, CLAMP THE WORKPIECE
IN PLACE BEFORE MAKING CUT.
Fig. 11
STARTING AND STOPPING
MITER SAW
To start the miter saw, depress switch trigger (A) Fig. 12.
To stop the miter saw, release the switch trigger.
This saw is equipped with an automatic electric blade
brake. As soon as the switch trigger (A) Fig. 12, is
released, the electric brake is activated and stops the
blade in seconds.
A TURNING SAW BLADE CAN BE
DANGEROUS. AFTER COMPLETING CUT, RELEASE
SWITCH TRIGGER (A) FIG. 12, TO ACTIVATE BLADE
BRAKE. KEEP CUTTINGHEAD DOWN UNTIL BLADE
HAS COME TO A COMPLETE STOP.
THE TORQUE DEVELOPED DURING
BRAKING MAY LOOSEN THE ARBOR SCREW. THE
ARBOR SCREW SHOULD BE CHECKED PERIODICALLY
AND TIGHTENED IF NECESSARY.
Fig. 12
A
A
A
B
B
A
A
11
LOCKING SWITCH IN THE
“OFF” POSITION
IMPORTANT: When the miter saw is not in use, the
switch should be locked in the OFF position using a
padlock (B) Fig. 13, with a 3/16" diameter shackle to
prevent unauthorized use of the saw.
Fig. 13
ROTATING TABLE FOR
MITER CUTTING
Your miter saw will cut any angle from a straight 90
degree cut to 47 degrees right and left. Loosen lock
handle (A) Fig. 14 one or two turns, depress index lever
(B), and move the control arm to the desired angle.
TIGHTEN LOCK HANDLE (A).
The miter saw is equipped with positive stops at the 0,
22.5, 31.6, and 45 degree right and left positions.
Loosen lock handle (A) Fig. 14, and move the control
arm until the bottom of the index lever (B) engages into
one of the positive stops, four of which are shown at (C).
TIGHTEN LOCK HANDLE (A). To disengage the
positive stop, depress index lever (B).
In addition, a triangle indicator (D) Fig. 16 is provided on
the miter scale at the 31.6 degrees right and left miter
positions for cutting crown moulding. (Refer to the
“CUTTING CROWN MOULDING” section of this
manual).
IMPORTANT: ALWAYS TIGHTEN LOCK HANDLE (A)
FIG. 15 BEFORE CUTTING.
Fig. 14
Fig. 16
Fig. 15
POINTER AND SCALE
A pointer (E) Fig. 16 is supplied to indicate the actual
angle of cut. Each line on the scale (F) represents 1
degree. When the pointer is moved from one line to the
next on the scale, the angle of cut is changed by 1
degree.
B
C
A
B
A
E
D
F
12
Fig. 17
ADJUSTING POINTER
If it becomes necessary to adjust the pointer (E) Fig. 17,
loosen screw (G), adjust the pointer (E) accordingly, and
tighten screw.
LOCKING CUTTINGHEAD
IN THE DOWN POSITION
When transporting the saw, the cuttinghead should
always be locked in the down position. Lower the cutting
arm (A) Fig. 18, and push in plunger (B) until other end of
plunger (B) engages with hole in cutting arm.
IMPORTANT: CARRYING THE MACHINE BY THE
SWITCH HANDLE WILL CAUSE MISALIGNMENT.
ALWAYS LIFT THE MACHINE BY THE BASE OR BY
THE CARRYING HANDLE (See Fig. 21).
Fig. 18
TILTING CUTTINGHEAD FOR
BEVEL CUTTING
The cuttinghead of your compound miter saw can be
tilted to cut any bevel angle from a 90 degree straight
cut off to a 45 degree left bevel angle. Loosen bevel lock
handle (A) Fig. 19, tilt cutting arm (B) to the desired
angle, and tighten lock handle (A).
Positive stops are provided to rapidly position the saw
blade at 90 and 45 degrees to the table. Refer to the
section of this manual titled “ADJUSTING 90 AND 45
DEGREE BEVEL STOPS.” The bevel angle of the
cutting arm is determined by the position of the pointer
(C) Fig. 19 on the scale (D).
In addition, a triangle indicator is provided on the bevel
scale at the 33.9 degree bevel angle for cutting crown
moulding. Refer to the “CUTTING CROWN
MOULDING” section of this manual.
Fig. 19
REAR SUPPORT/CARRYING
HANDLE
A rear support bar (A) Fig. 20 is provided to prevent the
machine from tipping to the rear when the cuttinghead is
returned to the up position. For maximum support the
bar (A) should be pulled out as far as possible.
The support bar (A) Fig. 21 can also be used to carry the
machine.
Fig. 20
E
G
B
A
B
C
D
A
A
13
Fig. 21 Fig. 22
ADJUSTING BLADE
PARALLEL TO TABLE SLOT
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Lower the cutting arm. The saw blade (A) Fig. 22
should be parallel to the left edge (B) of the table opening.
2. If an adjustment is necessary, loosen three screws
(C) Fig. 22 and move the cutting arm until the blade is
parallel with the left edge (B) of the table opening and
centered in the slot. Then tighten the three screws (C).
ADJUSTING FENCE
90 DEGREES TO BLADE
If the fence (A) Fig. 23 is removed from the saw, readjust it after replacement so that it is 90 degrees to the
blade as follows:
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Place one end of the square (B) Fig. 23 against the
fence (A) and the other end against the blade.
2. To adjust, loosen the four screws (C) Fig. 24, and
adjust fence 90 degrees to the blade. Tighten the four
screws (C).
Fig. 23
Fig. 24
ADJUSTING DOWNWARD
TRAVEL OF SAW BLADE
DISCONNECT MACHINE FROM POWER
SOURCE.
1. The downward travel of the saw blade should be
limited to prevent the saw blade from contacting any
metal surfaces of the machine. This adjustment is made
by loosening locknut (A) Fig. 25, and turning adjusting
screw (B) in or out.
2. Lower the blade as far as possible. Rotate the blade
by hand to make certain the teeth do not contact any
metal surfaces and adjust if necessary.
3. After the downward travel of the saw blade has been
adjusted, tighten locknut (A)
Fig. 25
A
A
B
C
B
A
C
C
A
B
14
ADJUSTING 90 AND 45
DEGREE BEVEL STOPS
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Loosen bevel lock handle and move the cutting arm
all the way to the right. Tighten the bevel lock handle.
2. Place one end of a square (A) Fig. 26 on the table
and the other end against the blade. Check to see if the
blade is 90 degrees to the table (Fig. 26).
3. If an adjustment is necessary, loosen locknut (B)
Fig. 27, and turn screw (C) until head of screw (C)
contacts casting (D) when blade is 90 degrees to the
table. Then tighten locknut (B).
4. Loosen bevel lock handle and move the cutting arm
all the way to the left bevel position and tighten bevel
lock handle.
5. Use a combination square (A) Fig. 28, to see if the
blade is at 45 degrees to the table, as shown.
6. If an adjustment is necessary, loosen locknut (E)
Fig. 29, and turn screw (F) until screw (F) contacts casting
(G) when blade is 45 degrees to the table. Then tighten
locknut (E).
7. Check to see that the bevel pointer P Fig. 29A, is
pointing to the 45 degree mark on the bevel scale (S)
Fig. 28. To adjust the bevel pointer P Fig. 29A, loosen
the screw (H) and adjust pointer (P) and tighten screw
(H) securely.
8. These positive stops enable you to rapidly position
the blade at the 90 and 45 degree bevel angle to the
table.
Fig. 26
Fig. 27
Fig. 29A
Fig. 28
Fig. 29
A
D
C
B
A
G
F
E
P
S
H
15
ADJUSTING TENSION
OF CUTTINGHEAD
RETURN SPRING
The tension of the cuttinghead return spring has been
adjusted at the factory so that the cuttinghead returns to
the up position after a cut has been made. If it becomes
necessary to re-adjust the spring tension, proceed as
follows:
DISCONNECT MACHINE FROM POWER
SOURCE.
Loosen locknut (A) Fig. 30 and turn screw (B) clockwise
to increase or counterclockwise to decrease the spring
tension. After the spring tension has been adjusted,
tighten locknut (A).
Fig. 30
TYPICAL OPERATIONS AND HELPFUL HINTS
1. Before cutting, make certain the cutting arm and
table are at their correct settings and firmly locked in
place.
2. Place the workpiece on the table and hold or clamp
it firmly against the fence. Fig. 31 illustrates an
accessory work clamp (A). The clamp (A) can also be
used on the right side of the machine (See Fig. 10).
3. If the workpiece causes your hand to
be within the hazard zone of of the saw blade, clamp the
workpiece in place before making cut.
4. For best results, cut at a slow, even cutting rate.
5. Never attempt freehand cutting (wood that is not
held firmly against the fence and table).
Fig. 31
AUXILIARY WOOD FENCE
When performing multiple or repetitive
cut-off operations that result in small cut-off pieces, one
inch or less, it is possible for the saw blade to catch the
cut-off pieces and project them out of the machine or
into the blade guard and housing, possibly causing
damage or injury. To limit the possibility of personal
injury or blade guard damage, an auxiliary wood fence
can be mounted to your saw.
Holes are provided in the fence to attach an auxiliary
fence (A) Fig. 32. This auxiliary fence is constructed of
straight wood approximately 1/2" thick by 3" high by 20"
long. NOTE: The auxiliary fence (A) is used ONLY with
the saw blade in the 0 degree bevel position (90 degrees
to the table). When bevel cutting (blade tilted), the
auxiliary fence will have to be removed.
Fig. 32
B
A
A
A
A
16
Fig. 33A Fig. 33B
Fig. 33E Fig. 33F
Fig. 33C
Fig. 33D
GENERAL CUTTING
OPERATIONS
1. Your machine has the capacity to cut standard 2 x 4’s
lying flat or on edge, at the 45 degree right and left miter
angles (Fig. 33A).
2. A standard 2 x 6 can be cut in the 90 degree straight
cut-off position in one pass (Fig. 33C) or at 45 degree
right or left miter angles (Fig. 33C).
3. Cutting a standard 4 x 4 can be accomplished with
one pass (Fig. 33D).
4. This machine has the capacity to accurately cut
crown moldings and other bevel-type cuts (Fig. 33E).
4. Cutting various sizes of plastic pipe is an easy job
with this machine (Fig. 33F).
17
Fig. 34
Fig. 35
CUTTING ALUMINUM
Aluminum extrusions such as used for making aluminum
screens and storm windows can easily be cut with
your compound miter saw. When cutting aluminum
extrusions, or other sections that can be cut with a saw
blade and are within the capacity of the machine,
position the material so the blade is cutting through the
smallest cross-section (Fig. 34). The wrong way to cut
aluminum angles is illustrated in Fig. 35. Be sure to apply
a stick wax to the blade before cutting aluminum stock.
This stick wax is available at most industrial mill supply
houses. The wax provides proper lubrication and keeps
chips from adhering to the blade.
NEVER APPLY LUBRICANT TO THE
BLADE WHILE THE MACHINE IS
RUNNING.
FENCE
BLADE
WRONG
FENCE
BLADE
RIGHT
CUTTING BOWED MATERIAL
When cutting flat pieces, first check to see if the material
is bowed. If it is, make sure the material is positioned on
the table as shown in Fig. 36.
If the material is positioned the wrong way, as shown in
Fig. 37, the workpiece will pinch the blade near the
completion of the cut.
RIGHT
WRONG
Fig. 36
Fig. 37
18
CUTTING
CROWN MOULDING
One of the many features of your saw is the ease of
cutting crown moulding.The following is an example of
cutting both inside and outside corners on 52/38 degree
wall angle crown moulding. NOTE: When cutting 45 degree
wall angle crown moulding, the following procedure for
inside and outside corners is the same with the
exception that the bevel position will always be at 30
degrees and the miter position will be 35.25 degrees to
the right or left.
1. Move the table to the 31.6 degree right miter
position and lock the table in position. NOTE: A triangle
indicator is provided on the miter scale to find this angle
quickly (Fig. 38)
2. Tilt the saw blade to the 33.9 degree left bevel
position and tighten bevel lock handle. NOTE: A triangle
indicator is provided on the bevel scale to find this angle
quickly (Fig. 39).
3. Place the crown moulding on the table with the
CEILING EDGE of the moulding against the fence, and
make the cut (Fig. 38). NOTE: The piece of crown
moulding used for the outside corner will always be on
the right hand side of the blade (A) Fig. 38. The piece of
crown moulding used for the inside corner will always be
on the left hand side of the blade (B) Fig. 38.
4. To make the matching halves of the inside and
outside corners, rotate the table to the 31.6 degree left
miter position and tighten table lock handle. NOTE: A
triangle indicator is provided on the miter scale to find
this angle quickly (Fig. 39).
5. Place the crown moulding on the table with the
WALL EDGE of the crown moulding against the fence
and make the cut. Again, the piece of crown moulding
used for the outside corner will always be on the right
side of the blade (C) Fig. 39. The piece of crown
moulding used for the inside corner will always be on the
left side of the blade (D) Fig. 39.
6. Fig. 40 illustrates the two outside corner pieces - (A)
being the piece cut at (A) Fig. 38, and (C) being the piece
cut at (C) Fig. 39.
7. Fig. 41 illustrates the two inside corner pieces - (B)
being the piece cut at (B) Fig. 38, and (D) being the piece
cut at (D) Fig. 39.
Fig. 38
Fig. 41
Fig. 39
Fig. 40
B
A
D
C
C
A
B
D
19
MAINTENANCE
CHANGING THE BLADE
USE ONLY CROSS-CUTTING SAW
BLADES.
WHEN USING CARBIDE TIPPED
BLADES, DO NOT USE BLADES WITH
DEEP GULLETS AS THEY CAN DEFLECT
AND CONTACT THE GUARD.
USE ONLY 10″″DIAMETER SAW BLADES
WHICH ARE RATED FOR 5200 RPM OR
HIGHER AND HAVE 5/8″″DIAMETER
ARBOR HOLES.
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Remove screw (A) Fig. 42 and rotate cover (B) to the
rear (Fig. 43).
Fig. 42
Fig. 43
Fig. 45
Fig. 44
2. To remove the saw blade, insert hex wrench (C)
Fig. 44 into the hex hole located on the rear end of the
motor shaft to keep the shaft from turning.
3. Use a wrench (G) Fig. 45 to loosen arbor screw (E)
by turning it clockwise.
4. Remove arbor screw (E) Fig. 45, outside blade
flange (F), and saw blade from saw arbor.
5. Attach new saw blade MAKING CERTAIN TEETH
OF SAW BLADE ARE POINTING DOWN AT THE
FRONT. Re-attach outside blade flange (F) Fig. 45, and
arbor screw (E) by turning it counterclockwise using
wrench (G) Fig. 45. At the same time, use hex wrench (C)
Fig. 44 to keep the arbor from turning.
6. Replace screw and cover that was rotated to the
rear in STEP 1.
REMOVE WRENCHES (C) FIG. 44 AND (G)
FIG. 45 BEFORE STARTING MACHINE.
A
B
B
C
E
F
G
20
BRUSH INSPECTION
AND REPLACEMENT
Brush life varies. It depends on the load on the motor.
Check the brushes after the first 50 hours of use for a
new machine or after a new set of brushes has been
installed. After the first check, examine them after about
10 hours of use until such time that replacement is
necessary. To inspect the brushes, proceed as follows:
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Remove three screws (A) Fig. 46 and remove motor
cover (B).
3. Fig. 48 illustrates one of the brushes (E) removed
from the holder (C). When the carbon on either brush (E)
is worn to 3/16″ in length or if either spring (F) or shunt
wire is burned or damaged in any way, replace both
brushes. If the brushes are found to be serviceable after
re-moving, reinstall them in the same position.
2. The brushes are located in the two holders (C) Fig. 47.
Remove spade type terminal connector (D) and pull out
brush holders (C).
Fig. 46
Fig. 47
Fig. 48
A
A
B
D
D
C
C
F
E
C
21
NOTES
22
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site
www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested with this
product, use of such accessories could be hazardous. For
safest operation, only Delta
recommended accessories should be used with this product.
ACCESSORIES
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.
The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,
BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series
2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®,
JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET
CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®,
Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFELOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®,
STAIR EASE®, The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL
SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®,
UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE®, WHISPER
SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y
también pueden estar registradas en otros países.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE
• DELTA)
Parts and Repair Service for Porter-Cable •Delta Machinery are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta)
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable
·
Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable
·
Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable
·
Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable
·
Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable
·
Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable
·
Delta más cercano.
ARIZONA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
CALIFORNIA
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
COLORADO
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
MISSOURI
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Houston 77038
4321 Sam Houston Parkway,
West
Suite 180
Phone: (281) 260-8887
Fax: (281) 260-9989
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Printed in U.S.A. PC-0603-149
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
MANITOBA
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
QUÉBEC
1515 ave.
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
Loading...