Delta MO1005-EA User Manual

Page 1

MO1005-EA

Operation Guide 3216

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully.

• The measurement functions built into this watch are not intended for taking measurements that require professional or industrial precision. Values produced by this watch should be considered as reasonable representations only.

• The Moon phase indicator and tide graph data that appear on the display of this watch are not intended for navigation purposes. Always use proper instruments and resources to obtain data for navigation purposes.

• This watch is not an instrument for calculating low tide and high tide times. The tide graph of this watch is intended to provide a reasonable approximation of tidal movements only.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by you or any third party arising through the use of this product or its malfunction.

Keep the watch exposed to bright light

Bright Light

Solar cell

• The watch continues to operate, even when it is not exposed to light. Leaving the watch in the dark can cause the battery to run down, which will result in some watch functions to be disabled. If the battery goes dead, you will have to re-configure watch settings after recharging. To ensure normal watch operation, be sure to keep it exposed to light as much as possible.

Battery charges in the light. Battery discharges in the dark.

Solar cell (Converts light to electrical power.)

Bright Light

LEVEL 1

LEVEL 2

LEVEL 3

Charge

LEVEL 4

Rechargeable battery

General Guide

• Press C to change from mode to mode.

• In any mode (except when a setting screen is on the display), press B to illuminate

the display.

• When you return to the Timekeeping Mode, the day of the week will be displayed after the name of the site you selected. See “Tide Site Name List” for more information about the site.

Timekeeping Mode

Warning!

The electricity generated by the solar cell of the watch is stored by a rechargeable battery. Leaving or using the watch where it is not exposed to light causes the battery to run down. Make sure the watch is exposed to light as much as possible.

• When you are not wearing the watch on your wrist, position the face so it is pointed at a source of bright light.

• You should try to keep the watch outside of your sleeve as much as possible. Charging is reduced significantly if the face is covered only partially.

Electrical energy

All functions enabled

Press C.

Tide/Moon Data Mode

▲

Dis-

charge

LEVEL 1

LEVEL 2

Some or all

LEVEL 3

functions

LEVEL 4

disabled

▲

• The actual level at which some functions are disabled depends on the watch model.

• Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window Approximately about 8 hours exposure to indoor fluorescent lighting

• Be sure to read “Power Supply” for important information you need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function has turned off the display to conserve power.

• See “Power Saving Function” for more information.

About This Manual

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in the “Reference” section.

▲

World Time Mode

▲

Alarm Mode

Countdown Timer Mode Stopwatch Mode

▲

Timekeeping

Current Time

Day of week

PM indicator

Site name

Month – Day

Hour : Minutes Seconds

▲

To set the time and date manually

3. Press C to move the flashing in the sequence shown below to select the other

settings.

City Code

• The following steps explain how to configure timekeeping settings only.

Press the A button to view the current site name setting. Use the Timekeeping Mode to set and view the current time and date.

Read This Before You Set the Time and Date!

This watch is preset with a number of city codes, each of which represents the time zone where that city is located. When setting the time, it is important that you first select the correct city code for your Home City (the city where you normally use the watch). If your location is not

included in the preset city codes, select the preset city code that is in the same time zone as your location.

• Note that all of the times for the World Time Mode city codes are displayed in accordance with the time and date settings you configure in the Timekeeping Mode.

1. In the Timekeeping Mode hold down A until the city

code starts to flash, which indicates the setting screen.

2. Use D and B to select the city code you want.

• Make sure you select your Home City code before changing any other setting.

• For full information on city codes, see the “City Code Table”.

12/24-Hour

DST

Illumination

Duration

Format

Seconds

Button

Operation Tone

DayPower Saving

Hour

Month

Minutes

Year

4. When the timekeeping setting you want to change is flashing, use D or B to

change it as described below.

Screen: To do this: Do this:

5. Press A to exit the setting screen.

• The day of the week is displayed automatically in accordance with the date (year, month, and day) settings.

Change the city code

Toggle between Daylight Saving Time ( ) and Standard Time ( ).

Toggle between 12-hour ( hour ( ) timekeeping

Reset the seconds to

Change the hour and minutes

Change the year, month, or day

Toggle the button operation tone between

(on) and (off)

Toggle the illumination duration between

(approximately 1.5 seconds) and (approximately 3 seconds).

Toggle between Power Saving on ( off (

)

) and 24-

) and

Use D (east) and B (west).

Press D.

Use D (+) and B (–).

Press D.

Page 2

Operation Guide 3216

12-hour and 24-hour timekeeping

• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for times in the range of noon to 11:59 p.m. and no indicator appears to the left of the hour digits for times in the range of midnight to 11:59 a.m.

• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without any indicator.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is applied in all other modes.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time.

To change the Daylight Saving Time (summer time) setting

DST indicator

4. When the setting you want is selected, press A twice to exit the setting screen.

• The DST indicator appears to indicate that Daylight Saving Time is turned on.

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C and the DST setting screen appears.

3. Use D to toggle the DST settings in the sequence

shown below.

DST off (

) DST on ( )

Tide/Moon Data

In the Tide/Moon Data Mode, you can see the tide for the tide site you selected at specified time and the current date’s moon phase for your Home City. You can specify a date and view tide and moon data for that date.

• See “Moon Phase Indicator” for information about the moon phase indicator and “Tide Graph” for information about the tide graph.

• All of the operations in this section are performed in the Tide/Moon Data Mode.

Note

• It takes about two seconds to calculate tide graph data. You will not be able to display a setting screen while data calculation is in progress.

• Moon age is calculated to an accuracy of ±1 day.

• You can view the current tide and moon age graph in the Timekeeping Mode.

Tide Data

The Tide Graph that appears first when you enter the Tide/Moon Data Mode shows the data at 6:00 a.m. for your currently selected tide site on the current date, according to the Timekeeping Mode. From there you can specify another time on the same date.

• If the tide data is not correct, check your Timekeeping Mode settings and correct them if necessary. See “To configure tide site settings” for more information.

• If you feel that the information shown by the Tide Graph is different from actual tide conditions, you need to adjust the high tide time. See “Adjusting the High Tide Time” for more information.

Moon Data

The moon phase and moon age information that appears first when you enter the Tide/Moon Data Mode shows the data at noon for your currently selected Home City on the current date, according to the Timekeeping Mode. After that you can specify another date to view data.

• If the moon data is not correct, check your Timekeeping Mode settings and correct them if necessary.

• If the moon phase indicator shows a phase that is a mirror image of the actual moon phase in your area, you can use the procedure under “Reversing the Displayed Moon Phase” to change it.

Tide/Moon Data Screens

In the Tide/Moon Data Mode, press A to toggle between the tide data screen and the moon data screen.

Tide Data Screen Moon Data Screen

Current tide range

• When you display the Tide Data Screen, it initially shows tide data for 6:00 a.m.

• Use the Tide Data Screen to specify the Tide Data time. You can use D to change

the displayed time in one-hour increments. The Tide Data time is scrolled within the current date only. Scrolling past midnight does not change the date.

• Use the Moon Data Screen to specify the Tide/Moon Data date. You can use D to change the displayed date in one-day increments. Pressing D will display the year of the displayed date.

Adjusting the High Tide Time

Use the following procedure to adjust the high tide time within a particular date. You can find out high tide information for your area from a tide table, the Internet, or your local newspaper.

To adjust the high tide time

Hour

Minute

Current tide level

Press A.

▲

Time

Month – Day

1. In the Tide/Moon Data Mode, use A to display the

Moon Data Screen.

2. Use D to scroll the date until one whose high tide time

you want to change is displayed.

3. Hold down A until the hour digits start to flash.

4. Use D (+) and B (–) to change the hour setting.

5. When the hour is the setting you want, press C.

• This will cause the minute digits to flash.

6. Use D (+) and B (–) to change the minute setting.

7. When the minute setting is the way you want, press A

to exit the adjustment screen and return to the Tide/ Moon Data Mode screen.

• Pressing D and B at the same time while the time

adjustment screen is displayed (steps 4 through 7 above) will return the high tide time to its initial factory default setting.

• The high tide time setting is affected by the DST (summer time) setting of the Timekeeping Mode.

Moon age

Moon phase

Month – Day

• On some days, there are two high tides. With this watch, you can adjust the first high tide time only. The second high tide time for that day is adjusted automatically based on the first high tide time.

Reversing the Displayed Moon Phase

The left-right (east-west) appearance of the Moon depends on whether the Moon is north of you (northerly view) or south of you (southerly view) as you view it. You can use the procedure below to reverse the displayed Moon phase so it matches the actual appearance of the Moon where you are located.

• To determine the viewing direction of the Moon, use a compass to take a direction reading of the Moon at its meridian passage.

• For information about the Moon phase indicator, see “Moon Phase Indicator”.

To reverse the displayed Moon phase

1. In the Tide/Moon Data Mode, hold down A until the

hour digits start to flash.

2. Press C twice.

• This will cause the Moon phase indicator to flash. This is the indicator switching screen.

3. Press D to toggle the Moon phase indicator between

the southerly view (indicated by view (indicated by

• Northerly view: Moon is north of you.

• Southerly view: Moon is south of you.

4. When the Moon phase indicator setting is the way you

want, press A to exit the switching screen and return to the Tide/Moon Data Mode screen.

) and northerly

World Time

City code

Current time in selected city

To view the time in another city

While in the World Time Mode, press D (eastward) to scroll through the city codes (time zones).

• Pressing the D and B at the same time will jump to the UTC time zone.

To toggle a city code time between Standard Time and Daylight Saving Time

DST indicator

World Time shows the current time in 48 cities (31 time zones) around the world.

• The times kept in the World Time Mode are synchronized with the time being kept in the Timekeeping Mode. If you feel that there is an error in any World Time Mode time, check to make sure you have the correct city selected as your Home City. Also check to make sure that the current time as shown in the Timekeeping Mode is correct.

• Select a city code in the World Time Mode to display the current time in any particular time zone around the globe. See the “City Code Table” for information about the UTC differential settings that are supported.

• All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.

1. In the World Time Mode, press D to display the city

code (time zone) whose Standard Time/Daylight Saving Time setting you want to change.

2. Hold down A to toggle between Daylight Saving Time

(DST indicator displayed) and Standard Time (DST indicator not displayed).

• The DST indicator is shown on the World Time Mode screen while Daylight Saving Time is turned on.

• Note that the Standard Time/Daylight Saving Time setting affects only the currently displayed city code. Other city codes are not affected.

• Note that you cannot switch between Standard Time and Daylight Saving Time while UTC is selected as the city code.

Alarms

Alarm number

Alarm time (Hour : Minutes)

To set an alarm time

• To set a one-time alarm, display alarm screen AL1, AL2, AL3 or AL4. To set the snooze alarm, display the

• The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

• This operation turns on the alarm automatically.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D (+) and B (–) to change it.

• With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).

5. Press A to exit the setting screen.

The Alarm Mode gives you a choice of four one-time alarms and one snooze alarm. Also use the Alarm Mode to turn the Hourly Time Signal (

SIG) on and off.

• There are five alarm screens numbered

AL3 and AL4 for the one-time alarm, and a snooze

alarm screen indicated by Signal screen is indicated by

• All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is displayed.

SNZ screen.

SNZ. The Hourly Time

SIG.

AL1, AL2,

Page 3

Operation Guide 3216

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the watch is in. In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, until you turn the alarm off.

• Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode time.

• To stop the alarm tone after it starts to sound, press any button.

• Performing any one of the operations below during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen Displaying the

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn an alarm on and off

Snooze alarm indicator

To turn the Hourly Time Signal on and off

SNZ

Alarm on indicator

Hourly time signal on indicator

setting screen

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on and off.

• Turning on a alarm (

SNZ) displays the alarm on indicator on its Alarm Mode

screen.

• In all modes, the alarm on indicator is shown for any alarm that currently is turned on.

• The alarm on indicator flashes while the alarm is sounding.

• The snooze alarm indicator flashes while the snooze alarm is sounding and during the 5-minute intervals between alarms.

1. In the Alarm Mode, use D to select the Hourly Time

Signal (

2. Press A to toggle it on and off.

• The Hourly Time Signal on indicator is shown on the display in all modes while this function is turned on.

AL1, AL2, AL3, AL4 or

SIG).

Stopwatch

The stopwatch lets you measure elapsed time, split times, and two finishes.

• The display range of the stopwatch is 59 minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.

• All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.

Minutes

Seconds

1/100 second

To measure times with the stopwatch

Elapsed Time

Start

Split Time

Start

Two Finishes

Start

➤➤➤

Stop Re-start Stop

➤➤➤

Split (SPL displayed)

➤➤➤

Split

First runner finishes. Display time of first runner.

Split release Stop

Stop

Second runner finishes.

Split release

Display time of second runner.

➤

Clear

➤

Clear

➤

Clear

Countdown Timer

Number of Repeats

Minutes

Seconds

Timer 1

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero. The beeper stops after about 5 seconds or when you press any button.

To configure the countdown timer

Dual timers can be set with two different starting times. The watch can be configured so the two timers alternate, so when one reaches the end of its countdown, the other timer starts. You can specify a “number of repeats” value, which controls how many times the two-timer countdown operation is performed (1 = once, 2 = twice, etc.). The starting time of each timer can be set in five-second steps up to 99 minutes, 55 seconds. You can specify up to 10 repeats. The watch emits a short beep whenever either of the timers reaches the end of its countdown during an ongoing timer operation. The watch emits a 5-second beep when the end of the final timer operation (specified by the number of repeats) is reached.

1.While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current countdown start time starts to flash, which indicates the setting screen.

• If the countdown start time is not displayed, use the procedure under “To use the countdown timer” to display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

3. When the setting you want to change is flashing, use D and B to change it as

described below.

Setting

Minutes, Seconds

Number of Repeats

• To disable either timer, set 00'00" as its countdown start time.

4. Press A to exit the setting screen.

Screen

Use D (+) and B (–) to change the setting.

Button Operation

To use the countdown timer

Current repeat count

(Reset)

Current timer time

Press D while in the Countdown Timer Mode to start the countdown timer.

• The countdown is performed by alternating between Timer 1 and Timer 2. A short beep is emitted to signal a changeover from one timer to the other.

•

Pressing A while a countdown timer is stopped resets it to the start time specified by you.

• Press D to pause a countdown. Press D again to resume.

• The watch emits a 5-second beep when the end of the final timer operation

(specified by the number of repeats) is reached.

• Even if you exit the Countdown Timer Mode, the countdown timer operation continues and the watch beeps as required.

• To stop a countdown operation completely, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value.

Present number of repeats

Current time

(Start/Stop)

Timer 1 or 2

Illumination

Auto light switch on indicator

To illuminate the display manually

In any mode (except when a setting screen is on the display), press B to turn on illumination.

• The above operation turns on illumination regardless of the current auto light switch setting.

• You can use the procedure below to select either 1.5 seconds or 3 seconds as the illumination duration. When you press B, the illumination will remain on for about

1.5 seconds or 3 seconds, depending on the current illumination duration setting.

To specify the illumination duration

About the Auto Light Switch

Turning on the auto light switch causes illumination to turn on, whenever you position your wrist as described below in any mode. Note that this watch features a “Full Auto EL Light”, so the auto light switch operates only when available light is below a certain level. It does not turn on the backlight under bright light.

Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes illumination to turn on.

• Wear the watch on the outside of your wrist.

Warning!

••

• Always make sure you are in a safe place whenever you are reading the

••

display of the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not startle or distract others around you.

••

• When you are wearing the watch, make sure that its auto light switch is

••

turned off before riding a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down B for about three seconds to toggle the auto light switch on (auto light switch on indicator displayed) and off (auto light switch on indicator not displayed).

• The auto light switch on indicator is on the display in all modes while the auto light switch is turned on.

This watch has an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. The watch’s auto light switch turns on illumination automatically when you angle the watch towards your face.

• The auto light switch must be turned on (indicated by the auto light switch on indicator) for it to operate.

• See “Illumination Precautions” for other important information about using illumination.

1. In the Timekeeping Mode, hold down A until the

display contents start to flash. This is the setting screen.

2. Press C 10 times until the current illumination duration

setting (

3. Press D to toggle the setting between

(approximately 1.5 seconds) and (approximately 3 seconds).

4. Press A to exit the setting screen.

Parallel to ground

or ) appears.

More than 40°

Page 4

Operation Guide 3216

Power Supply

This watch is equipped with a solar cell and a rechargeable battery that is charged by the electrical power produced by the solar cell. The illustration shown below shows how you should position the watch for charging.

Example: Orient the watch so its face is

pointing at a light source.

• The illustration shows how to position a watch with a resin band.

• Note that charging efficiency drops when any part of the solar cell is blocked by clothing, etc.

• You should try to keep the watch outside of your sleeve as much as possible. Charging is reduced significantly if the face is covered only partially.

Important!

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is blocked from exposure to light can cause rechargeable battery power to run down. Be sure that the watch is exposed to bright light whenever possible.

• This watch uses a rechargeable battery to store power produced by the solar cell, so regular battery replacement is not required. However, after very long use, the rechargeable battery may lose its ability to achieve a full charge. If you experience problems getting the rechargeable battery to charge fully, contact your dealer or CASIO distributor about having it replaced.

• Never try to remove or replace the watch’s rechargeable battery yourself. Use of the wrong type of battery can damage the watch.

• All data stored in memory is deleted, and the current time and all other settings return to their initial factory defaults whenever battery power drops to Level 5 and when you have the battery replaced.

• Turn on the watch’s Power Saving function and keep it in an area normally exposed to bright light when storing it for long periods. This helps to keep the rechargeable battery from going dead.

Battery Power Indicator and Recover Indicator

The battery power indicator on the display shows you the current status of the rechargeable battery’s power.

Level

Battery power indicator

• The flashing LOW indicator at Level 3 tells you that battery power is very low, and that exposure to bright light for charging is required as soon as possible.

• At Level 5, all functions are disabled and settings return to their initial factory defaults. Once the battery reaches Level 2 after falling to Level 5, reconfigure the current time, date, and other settings.

• The watch’s Home City code setting will change automatically to TYO (Tokyo) whenever the battery drops to Level 5.

•

Display indicators reappear as soon as the battery is charged from Level 5 to Level 2.

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the battery power indicator to show a reading temporarily that is higher than the actual battery level. The correct battery level should be indicated after a few minutes.

Recover indicator

Charging Precautions

Certain charging conditions can cause the watch to become very hot. Avoid leaving the watch in the areas described below whenever charging its rechargeable battery. Also note that allowing the watch to become very hot can cause its liquid crystal display to black out. The appearance of the LCD should become normal again when the watch returns to a lower temperature.

Warning! Leaving the watch in bright light to charge its rechargeable battery can cause it to become quite hot. Take care when handling the watch to avoid burn injury. The watch can become particularly hot when exposed to the following conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

Charging Guide

The following table shows the amount of time the watch needs to be exposed to light each day in order to generate enough power for normal daily operations.

Battery Power Indicator

(Charge Soon Alert)

• Performing illumination, or beeper operations during a short period may cause the recover indicator to appear on the display. After some time, battery power will recover and the recover indicator will disappear, indicating that the above functions are enabled again.

• If the recover indicator appears frequently, it probably means that remaining battery power is low. Leave the watch in bright light to allow it to charge.

Exposure Level (Brightness)

Outdoor Sunlight (50,000 lux) Sunlight Through a Window (10,000 lux) Daylight Through a Window on a Cloudy Day (5,000 lux) Indoor Fluorescent Lighting (500 lux)

• For details about the battery operating time and daily operating conditions, see the “Power Supply” section of the Specifications.

• Stable operation is promoted by frequent exposure to light.

Solar cell

Function Status

All functions enabled.

Illumination, and beeper disabled.

Except for timekeeping and the CHG (charge) indicator, all functions and display indicators disabled.

All functions disabled.

Approximate

Exposure Time

5 minutes 24 minutes 48 minutes 8 hours

Recovery Times

The table below shows the amount exposure that is required to take the battery from one level to the next.

Exposure Level (Brightness)

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window (10,000 lux)

Daylight Through a Window on a Cloudy Day (5,000 lux)

Indoor Fluorescent Lighting (500 lux)

• The above exposure time values are all for reference only. Actual required exposure times depend on lighting conditions.

Approximate Exposure Time

Level 5 Level 4 Level 3 Level 2 Level 1

▲

2 hours 20 hours 6 hours

8 hours 99 hours 27 hours

15 hours - - - - - - - - - - - - - - - -

172 hours - - - - - - - - - - - - - - - -

Tide Site Name

Selecting the Tide Site Name

The tide site names you can select depend on your current Home City setting.

• Select tide site names in the Timekeeping Mode.

• After configuring the settings for your Home City, press A once to display the tide

site name selection screen.

• Note that the tide sites you can select are those located in the same time zone as your Home City. They are not necessarily located near your Home City.

To configure tide site settings

• Setting an accurate high tide time will allow the watch to produce accurate tide readings. Especially when “USER” is selected as the site, make sure that you input an accurate high tide time.

• Only a “USER” site can be selected while UTC is selected as the Home City.

1. In the Timekeeping Mode, hold down A for about two

seconds until the city code starts to flash. This is the setting screen.

• The watch will exit the setting screen automatically if you do not perform any operation for about two or three minutes.

2. Press A once to display the tide site name selection

screen.

• The current tide site name will be on the display and

SET will flash.

3. Use D (forward) and B (back) to scroll through the

tide site names until the one you want is displayed.

• If the tide site name is longer than four characters, the name will scroll from right to left on the display.

• A tide site that does not have any data assigned to it displays the name “USER”.

4. When all of the settings are the way you want, press A

to exit the setting screen.

• The tide graph in the Timekeeping Mode shows information for the site you select here.

• The tide site candidates are those with the UTC differential as the current Home City. If you cannot find the site you want, you can select “USER”.

• Only “USER” sites may be available for some cities.

Reference

This section contains more detailed and technical information about watch operation. It also contains important precautions and notes about the various features and functions of this watch.

Moon Phase Indicator

Moon Phase indicator

Moon Phase Indicator

Moon Age

Moon Phase

Moon phase (part you can see) (part you cannot see)

Moon Phase Indicator

Moon Age

Moon Phase

The Moon phase indicator of this watch indicates the current phase of the Moon as shown below. It is based on the view of the left side of the moon at meridian transit from the northern hemisphere of the Earth. If the appearance of the Moon phase indicator is reversed from the actual Moon as viewed from your location, you can use the procedure under “To reverse the displayed Moon phase” to change the indicator.

(part you cannot see)

28.7-29.8

1.0-2.7 2.8-4.6 4.7-6.4 6.5-8.3 8.4-10.1

0.0-0.9

New Moon

Moon phase (part you can see)

10.2-12.0

First Quarter (Waxing)

12.1-13.8

13.9-15.7 15.8-17.5 17.6-19.4 19.5-21.2 21.3-23.1 23.2-24.9 25.0-26.8 26.9-28.6

Full Moon

Last Quarter (Waning)

▲

Page 5

Operation Guide 3216

Tidal Movements

Tides are the periodic rise and fall of the water of oceans, seas, bays, and other bodies of water caused mainly by the gravitational interactions between the Earth, Moon and Sun. Tides rise and fall about every six hours. The Tide Graph of this watch indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal interval. The Tide Graph calculates and graphically represents current tide conditions in your currently selected site or USER site based on longitudes, lunar day length, and lunitidal interval preset in watch memory, and on high tide times specified by you.

Tide Graph

The Tide Graph graphically represents the current tide condition using one of three patterns that represent spring tide, intermediate tide, and neap tide, as shown below.

Tide Name Graph Description

Spring Tide

Intermediate Tide

Neap Tide

•

The Tide Graph flashes as shown below to indicate the tide range.

• The segments on either end of the Tide Graph flash during high tide.

Lunitidal Interval

Theoretically, high tide is at the moon’s transit over the meridian and low tide is about six hours later. Actual high tide occurs somewhat later, due to factors such as viscosity, friction, and underwater topography. Both the time differential between the moon’s transit over the meridian until high tide and the time differential between the moon’s transit over the meridian until low tide are known as the “lunitidal interval”. Tides data is calculated using the lunitidal intervals preset for each site.

Button Operation Tone

Mute indicator

To turn the button operation tone on and off

Power Saving Function

Power saving indicator

Elapsed Time

in Dark

60 to 70 minutes

6 or 7 days

• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.

• The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch

is already in the sleep state when 6:00 AM arrives, however, it will remain in the sleep state.

To recover from the sleep state

Perform any one of the following operations.

• Move the watch to a well-lit area.

• Press any button.

• Angle the watch towards your face for reading.

To turn Power Saving on and off

On/Off status

The button operation tone sounds any time you press one of the watch’s buttons. You can turn the button operation tone on or off as desired.

• Even if you turn off the button operation tone, alarms, the Hourly Time Signal, and other beepers all operate normally.

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C nine times until the current button operation

tone setting (

3. Press D to toggle the setting between

and

4. Press A to exit the setting screen.

• The mute indicator is displayed in all modes when the button operation tone is turned off.

When turned on, the Power Saving function enters a sleep state automatically whenever the watch is left in an area for a certain period where it is dark. The table below shows how watch functions are affected by the Power Saving function.

Display

Blank, with Power Saving indicator flashing

Blank, with Power Saving indicator not flashing

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C 11 times until the Power Saving on/off screen

appears.

3. Press D to toggle Power Saving on (

(

4. Press A to exit the setting screen.

• The Power Saving indicator is on the display in all modes while Power Saving is turned on.

Large difference between high tide and low tide. Occurs a few days before and after a New Moon and Full Moon.

Medium difference between high tide and low tide.

Small difference between high tide and low tide. Occurs a few days before and after the first quarter and last quarter of a half moon.

High tideLow tide

or ) appears.

(tone off).

All functions enabled, except for the display

Beeper tone, illumination, and display are disabled.

Operation

(tone on)

) and off

Auto Return

• If you do not perform any operation for about two or three minutes while a setting screen (with a flashing setting) is on the display, the watch will exit the setting screen automatically.

Scrolling

The B and D are used in various modes and setting screens to scroll through data on the display. In most cases, holding down these buttons during a scroll operation scrolls at high speed.

Initial Screens

When you enter the World Time Mode or Alarm Mode, the data you were viewing when you last exited the mode appears first.

Timekeeping

• Resetting the seconds to 00 while the current count is in the range of 30 to 59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are reset to 00 without changing the minutes.

• The year can be set in the range of 2000 to 2099.

• The watch’s built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to change it except after you have the watch’s battery replaced.

• The current time for all city codes in the Timekeeping Mode and World Time Mode is calculated in accordance with the Coordinated Universal Time (UTC) for each city, based on your Home City time setting.

World Time

• The seconds count of the World Time is synchronized with the seconds count of the Timekeeping Mode.

Illumination Precautions

• The electro-luminescent panel that provides illumination loses power after very long use.

• Illumination may be difficult to see when viewed under direct sunlight.

• The watch may emit an audible sound whenever the display is illuminated. This is

due to vibration of the EL panel used for illumination, and does not indicate malfunction.

• Illumination turns off automatically whenever an alarm sounds.

• Frequent use of illumination runs down the battery.

Auto light switch precautions

• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light switch to operate when it is not needed, which shortens battery life. If you want to wear the watch on the inside of your wrist, turn off the auto light switch feature.

More than 15 degrees too high

• Static electricity or magnetic force can interfere with proper operation of the auto light switch. If illumination does not turn on, try moving the watch back to the starting position (parallel with the ground) and then tilt it back toward you again. If this does not work, drop your arm all the way down so it hangs at your side, and then bring it back up again.

• Under certain conditions, illumination may not turn on until about one second after you turn the face of the watch towards you. This does not necessarily indicate malfunction of the auto light switch.

• You may notice a very faint clicking sound coming from the watch when it is shaken back and forth. This sound is caused by mechanical operation of the auto light switch, and does not indicate a problem with the watch.

• Illumination may not turn on if the face of the watch is more than 15 degrees above or below parallel. Make sure that the back of your hand is parallel to the ground.

• Illumination turns off after a preset amount of time (1.5 or 3 seconds), even if you keep the watch pointed towards your face.

Specifications

Accuracy at normal temperature: ± 15 seconds a month Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week

Time format: 12-hour and 24-hour Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099 Other: Home City code (can be assigned one of 48 city codes); Standard Time /

Daylight Saving Time (summer time); Checking a Tide Site

Tide/Moon Data:

Moon phase indicator for specific date; Tide level for specific date and time Other: High tide time adjustment; Moon phase reversal

World Time: 48 cities (31 time zones)

Other: Daylight Saving Time/Standard Time

Alarms: 5 daily alarms (four one-time alarms; one snooze alarm); Hourly Time Signal Stopwatch:

Measuring unit: 1/100 second Measuring capacity: 59' 59.99'' Measuring modes: Elapsed time, split time, two finishes

Countdown Timer:

Number of timers: 2 (one set) Setting unit: 5 seconds Range: 99 minutes 55 seconds each timer Countdown unit: 1 second Number of repeats: 1 to 10 5-second time up beeper

Illumination: EL (electro-luminescent panel); Full Auto Light Switch; Selectable

illumination duration

Other: Button operation tone on/off

Power Supply: Solar cell and one rechargeable battery

Approximate battery operating time: 11 months (from full charge to Level 4) under the following conditions:

• Watch not exposed to light

• Internal timekeeping

• Display on 18 hours per day, sleep state 6 hours per day

• 1 illumination operation(1.5 second) per day

• 10 seconds of alarm operation per day

Page 6

Operation Guide 3216

City Code Table

City

Code

PPG

ANC YVR

DEN MEX

NYC

LON MAD

ROM BER

• Based on data as of December 2009.

• The rules governing global times (UTC offset and GMT differential) and summer

City

Pago Pago

Honolulu

HNL

Anchorage

Vancouver

Los Angeles

LAX

Edmonton

YEA

Denver

Mexico City

Chicago

CHI

New York

Santiago

SCL

Halifax

YHZ

St. Johns

YYT

Rio De Janeiro

RIO

Fernando de Noronha

FEN

Praia

RAI

UTC

Lisbon

LIS

London

Madrid

Pari s

PAR

Rome

Berlin

Stockholm

STO

Athens

ATH

Cairo

CAI

Jerusalem

JRS

time are determined by each individual country.

UTC Offset/

GMT Differential

–11 –10

–9

–8

–7

–6

–5

–4

–3.5 –3 –2 –1

City

Code

MOW

JED THR DXB KBL KHI

DEL KTM DAC RGN BKK

SIN HKG

BJS TPE SEL TYO ADL

GUM

SYD NOU

WLG

City

Moscow

Jeddah Tehran

Dubai Kabul

Karachi

Delhi

Kathmandu

Dhaka

Yangon

Bangkok

Singapore

Hong Kong

Beijing

Taipei Seoul Tokyo

Adelaide

Guam

Sydney

Noumea

Wellington

UTC Offset/

GMT Differential

+3.5 +4 +4.5 +5 +5.5 +5.75 +6 +6.5 +7

+9.5

+10

+11 +12

Tide Site Name List

City

Code

LIS

LON

MAD

PAR ROM BER STO

ATH

CAI

JRS

MOW

JED THR DXB

KBL

KHI

DEL

KTM DAC RGN

BKK

SIN HKG

BJS

TPE

SEL

TYO

Tide Site

NEWQUAY,GBR ABERDEEN,GBR KILLALA BAY,IRL PENICHE,POR CASCAIS,POR FUNCHAL,

MADEIRA LAS PALMAS CASABLANCA,

MAR SAFI,MAR DAKAR,SEN USER BOUCAU,FRA PORTUGALETE,

ESP GIJON,ESP MARSEILLE,FRA PALERMO,ITA USER CAPE TOWN,RSA DURBAN,RSA MOSSEL BAY,

RSA USER TOLANARO,MAD USER USER LE PORT,

REUNION PORT LOUIS,

MRI USER USER MALE,

MALDIVES USER GALLE,SRI USER USER USER USER PHUKET TELUK DALAM,

NIAS PULAU TELO,

INA SIBERUT,INA NORTH PAGAI,

INA TANJUNG

PRIOK USER BENOA,BALI AMPENAN,

LOMBOK COWARAMUP FREMANTLE CATANDUANES,

PHI SIARGAO,PHI USER ENOSHIMA SHIMODA SHIKINEJIMA OMAEZAKI IRAGO WAKAYAMA KANNOURA HOSOSHIMA NISHINOOMOTE NAZE NAHA SENDAI SOMA KASHIMA KAZUSA-

KATSUURA USER

U.K. U.K. IRELAND PORTUGAL PORTUGAL MADEILA

GRAN CANARIA MOROCCO

MOROCCO SENEGAL

FRANCE SPAIN

SPAIN FRANCE ITALY

SOUTH AFRICA SOUTH AFRICA SOUTH AFRICA

MADAGASCAR

REUNION

MAURITIUS

MALDIVES

SRI LANKA

THAILAND INDONESIA

INDONESIA

INDONESIA INDONESIA

INDONESIA

INDONESIA INDONESIA

AUSTRALIA AUSTRALIA PHILIPPINES

PHILIPPINES

JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN JAPAN

• For information about city names, see the City Code Table.

City

Code

ADL

VICTOR HARBOR

USER

GUM

NOOSA HEADS

SYD

BUNDALL POINT DANGER TWEED RIVER BYRON BAY BALLINA SYDNEY ULLADULLA LORNE HOBART GUAM USER

NOU

NOUMEA USER

WLG

SUVA,FIJ RAGLAN,NZL USER

PPG

PAGO PAGO

USER

HNL

HONOLULU WAIALUA BAY,

OAHU KAHULUI,MAUI HILO BAY,

HAWAII NAWILIWILI,

KAUAI PAPEETE,TAHITI USER

ANC

USER

YVR

SAN FRANCISCO

LAX

MONTEREY PORT SAN LUIS SANTA BARBARA PORT HUENEME SANTA MONICA L.A.HARBOR NEWPORT BAY LA JOLLA ENSENADA,MEX USER

YEA

USER

DEN

USER

MEX

MANZANILLO,MEX

CHI

PUNTARENAS,CRC USER

NYC

ATLANTIC CITY VIRGINIA BEACH PORT CANAVERAL MIAMI HARBOR KINGSTON,JAM BALBOA,PAN PUERTO

LOPEZ,ECU PUERTO

CHICAMA USER

SCL

SANTO DOMINGO

YHZ

SAN JUAN,PUR BRIDGETOWN VALPARAISO,CHI USER

YYT

USER

RIO

RIO DE JANEIRO

SANTOS USER

FEN

F.D.NORONHA USER

RAI

PONTA DELGADA USER

Tide Site

AUSTRALIA

AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA AUSTRALIA GUAM

NEW CALEDONIA

FIJI ISLANDS NEW ZEALAND

AMERICAN SAMOA

U.S. A. U.S. A.

U.S. A.

TAH I T I

U.S. A. U.S. A. U.S. A. U.S. A. U.S. A. U.S. A. U.S. A. U.S. A. U.S. A. MEXICO

MEXICO COSTA RICA

U.S. A. U.S. A. U.S. A. U.S. A. JAMAICA PANAMA EQUADOR

PERU

DOMINICAN R. PUERTO RICO BARBADOS CHILE

BRAZIL

AZORES

Delta MO1005-EA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Getting Acquainted

General Guide

Timekeeping

Tide/Moon Data

World Time

Alarms

Stopwatch

Countdown Timer

Illumination

Power Supply

Tide Site Name

Reference

Specifications

City Code Table

Tide Site Name List