Delta 50-875 User Manual

INSTRUCTION MANUAL

PART NO. 907370 - 02-25-04

Copyright © 2004 Delta Machinery

ESPAÑOL: PÁGINA 11

To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,
please call

1-800-223-7278 (In Canada call 1-800-463-3582).

Air Cleaner

50-875

2

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.

This manual contains information that is important for you to know and understand. This information relates to protect­ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols below. Please read the manual and pay attention to these sections.

SAFETY GUIDELINES - DEFINITIONS

GENERAL SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility. For additional information please visit our website www.deltamachinery.com.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this

machine not be modified and/or used for any application other than that for which it was designed. If you have any
questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine
if it can or should be performed on the product.

Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

1. FOR YOUR OWN SAFETY, READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE OPERATING THE
UNIT. Learn the unit’s application and limitations as well as the specific hazards peculiar to it.

2. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

3. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use this unit in damp or wet locations, or expose it to rain. Keep
work area well-lighted.

4. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area.

5. DISCONNECT UNIT before servicing.

6. CHECK DAMAGED PARTS. Before further use of the unit, properly repair or replace any part that is damaged.

3

ADDITIONAL SAFETY RULES

FOR AIR CLEANERS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others

.

04-24-03

DO NOT USE THIS UNIT TO FILTER
METAL DUST. Combining wood and

metal dust can create an explosion or
fire hazard. This unit is intended to filter
non-explosive atmospheres only.

DO NOT USE THIS UNIT TO DISSIPATE
FUMES OR SMOKE. Explosions or fire can

result. This air cleaner is intended for use
where only dry airborne dust is present.
Its use should be limited to non­explosive, non-metallic atmospheres.

1. DO NOT OPERATE THIS UNIT until it is completely

assembled and installed according to the instructions.
A unit incorrectly assembled can cause injury.

2. OBTAIN ADVICE from your supervisor, instructor, or

another qualified person if you are not thoroughly
familiar with the operation of this unit. Knowledge is
safety.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections to prevent electrical shock or
electrocution.

4. DO NOT LIFT THIS UNIT BY THE POWER CORD.

Do not use the power cord as a hanging device. A
damaged power cord can cause electrical shock or
electrocution.

5. SECURELY ANCHOR THIS UNIT to a permanent or

fixed supporting structure when suspending it from
the ceiling. A falling unit can cause serious injury.
Always keep a minimum of 7 feet between the
bottom of the unit and the floor surface to allow for
sufficient head clearance. Use only a chain rated for
a minimum of 150 lb. working load to adequately
hold the unit. Use steel S-Hooks that are at least
1/4" in diameter to suspend the unit from the ceiling.
Lag-type bolts used to suspend the unit from the
ceiling must be threaded at least 1-1/2" into
supporting structural members.

6. SUPPORT THIS UNIT or securely clamp it to the

work surface when it is used in a portable
application to eliminate potential injury and/or
damage to the unit.

7. ENSURE THAT THE INTAKE AND EXHAUST
AREAS ARE CLEAR prior to starting the unit.
Clogged intakes or exhausts can cause an
explosion and/or fire.

8. KEEP ARMS, HANDS, AND FINGERS AWAY
FROM THE FAN. Avoid all exposure to rotating
parts to prevent injury.

9. DO NOT OPERATE THIS UNIT WITHOUT THE
FILTERS IN PLACE. Dust and other small debris
will go directly to the motor, causing over-heating
and the potential for fire and/or explosion.

10. DO NOT ATTEMPT to remove or replace the filter(s)
while the unit is running. Exposed fan blades can cause
severe cuts. Make certain that the unit is
disconnected from the power source.

11. MAINTAIN THE UNIT in top condition. Clogged
filters can increase the potential for fire or
explosion. Follow all instructions for changing and
cleaning filters.

12. STORE THE UNIT in a location that eliminates
the potential for damage to the power cord. A
damaged power cord can cause shock or
electrocution. Safely store power cord on the unit
to eliminate tripping hazards.

13. TURN THE UNIT “OFF” and disconnect the unit
from the power source before installing or
removing accessories, before adjusting or
changing set-ups, or when making repairs. An
accidental start-up can cause serious injury.

4

4

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3­prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

Fig. A Fig. B

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

2. Grounded, cord-connected machines intended
for use on a supply circuit having a nominal rating
less than 150 volts:

If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.

NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.

IN ALL CASES, MAKE CERTAIN THE
RECEPTACLE IN QUESTION IS
PROPERLY GROUNDED. IF YOU ARE
NOT SURE, HAVE A QUALIFIED ELEC­TRICIAN CHECK THE RECEPTACLE.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment­grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.

Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment­grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.

Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.

Repair or replace damaged or worn cord immediately.

POWER CONNECTIONS

MOTOR SPECIFICATIONS

Your machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.

EXTENSION CORDS

Use proper extension cords. Make sure
your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type
plug and matching receptacle which will accept the
machine’s plug. When using an extension cord, be sure
to use one heavy enough to carry the current of the
machine. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating. Fig.
D-1 shows the correct gauge to use depending on the
cord length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.

Fig. D-1

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 120

up to

25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG
12-16 120 25-50 12 AWG
12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

FUNCTIONAL DESCRIPTION

FOREWORD

Model 50-875 Delta Air Cleaner is specifically designed to quietly circulate and filter non-metallic dust which is
generated throughout the work area. The Air Cleaner is furnished with two filters: an outer filter which filters particles
that are five microns and larger, and a secondary disposable filter that captures 91% of the dust particles that are one
micron and larger (one micron = one millionth of a meter). Because breathing microscopic particles can be a potential
health hazard, filtering microscopic dust particles offers a cleaner and safer environment. This Air Cleaner will filter the
air in a room measuring 20’ x 20’ x 8’ either 13, 16, or 18 times an hour, depending on the setting. If desired, multiple
units can be used to filter larger areas. An occasional cleaning and/or replacement of filters is the only required
maintenance.

Fig. 1A

1

Fig. 1B

1. Air cleaner

2. Remote Control Unit
(Batteries not included)

3. 1” Eye-Bolts (4)

4. Rubber Feet (4)

5. 1/4-20 Flange Nuts (4)

CARTON CONTENTS

5

2

3 4

5

6

ASSEMBLY

Fig. 2C

Fig. 2A

Fig. 2B

A

The Air Cleaner is shipped complete in one shipping container. Carefully unpack the Air Cleaner and all loose
items from the shipping container.

Styrofoam blocks have been packed inside the unit for protection. REMOVE THESE BLOCKS (A) Fig. 1 prior
to use. To Remove:

1. Disconnect unit from power source.

2. Remove outer filter by lifting up on the bottom and pulling out (Fig. 2A).

3. Remove inner filter by lifting up on the bottom and pulling out (Fig. 2B).

4. Remove styrofoam blocks (A) Fig. 2C and replace filters.

DO NOT LIFT THE AIR CLEANER BY POWER CORD.

UNPACKING AND CLEANING

The air cleaner cabinet has convenient lifting handles located on either side (one of which is shown at (A) Fig. 4). To
avoid damage to the air filters, carry the air cleaner with the filters positioned away from your body.

Locate (4) self-adhesive rubber feet (A) Fig. 3 supplied with the unit. Carefully place the Air Cleaner on a firm
supporting surface with access to the bottom of the cabinet. Apply a self-adhesive rubber foot (A) Fig. 3 to the bottom
at each corner of the air cleaner cabinet. The rubber feet will help eliminate vibration and will prevent the possibility of
the air cleaner “walking” across the floor or work surface.

For operator safety, clamp the unit to a work bench or position it securely on sawhorses.

USING THE AIR CLEANER ON A BENCH OR FLOOR SURFACE

Determine whether the Air Cleaner will be used on the floor, on a bench, or hanging from an overhead support. If the
Air Cleaner will be used as a mobile unit, proceed to “USING THE AIR CLEANER ON A BENCH OR FLOOR

SURFACE” section. If the unit will be ceiling-mounted, proceed to section “MOUNTING THE AIR CLEANER TO A
CEILING OR OVERHEAD SUPPORT.”

When determining where to mount the air cleaner, always select a location where the air flow is

unrestricted. Do not locate the unit in a corner or near any heating or cooling vents.

IMPORTANT:

Fig.4

Fig. 3

A

A

7

Never secure the air cleaner hardware to drywall, drop ceiling tile/frame, or other non-structural
members.

This unit weighs approximately 60 pounds. When mounting overhead, be certain that the unit is
securely fastened and supported.

1. Locate the four 1" eye bolts and the four 1/4-20 flange nuts supplied with the unit.

2. Use a flat blade screwdriver (not supplied) to remove the four screws (C) Fig. 5 from the top of air cleaner (D).

3. Thread one flange nut on each bolt approximately 3/4".

4. Thread the eye-bolts (F) Fig. 6 into the four holes where the screws were removed in STEP 2.

Be certain that the flange nuts are tightened against the surface of the air cleaner.

When suspending the air cleaner from the ceiling or other overhead support, use steel s-hooks that are a
minimum of 1/4".

Thread all lag hooks at least 1-1/2" into the supporting structural members.

MOUNTING THE AIR CLEANER TO THE CEILING OR OVERHEAD SUPPORT

Keep a minimum of seven feet between bottom of air cleaner and the floor surface.

DO NOT use rope, cable, or power cord to suspend the unit from the ceiling. Use chain rated for a minimum of
a 150 lb. working load.

IMPORTANT: When determining a location to mount the unit, the air cleaner will operate more efficiently when
the air flow is unrestricted. Do not locate the unit in a corner or near any heating or cooling vents.

Fig. 5

Fig. 6

NOTE:
NOTE:

NOTE:

C

D

F

ON/OFF SWITCH

The Air Cleaner is equipped with an in-line rocker switch
(M) Fig.7, located on the power cord (N). To start or stop
the motor, press downward on the rocker switch,
according to the markings on the side. When you are
finished with the air cleaner, turn the switch off rather
than unplug the unit.

NOTE: The ON-OFF Switch must be turned “ON” before
using the remote control feature.

Fig. 7

N

M

8

Fig. 8A

USING THE REMOTE CONTROL

To reduce the risk of fire or electric
shock, do not use this unit with any
solid-state speed control device.

The remote control provided with this unit is not con­sidered a solid-state device.

The Air Cleaner is equipped with a REMOTE CONTROL
(A) Fig.8A.

NOTE: The remote requires two (2) AAA batteries (not
supplied). The Battery housing is located underneath the
back cover.

Notice that the remote control has three control buttons
(Fig. 8A): TIME (B), ON/OFF (C), and SPEED (D). These
buttons correspond to the LED sensor panel on the rear
of the machine (K) Fig. 10B.

NOTE: When the machine is connected to the power
source, a green light (E) will be activated on the panel.

To activate the blower unit, press the “ON/OFF” button
(C) Fig. 8A. The machine will begin in the default speed
of Low or “L” on the sensor panel. Press the SPEED
button once, and the machine will run at the high (or “H”
level). Press the SPEED button again, and the machine
will run at the medium speed (or “M”). Press the SPEED
button a third time, and the machine will return to the
Low Speed mode.

To turn the machine off, press the “ON/OFF” button (C)
Fig. 8A.

Fig. 8B

This unit has a timer that can be set by remote control.

When the “TIME” button (B) Fig. 8A is pressed on the
remote control, the machine will run for 1/2 hour. (An
LED light will show up on the sensor panel (F) Fig. 8B).
Pressing the “TIME” button again will set the machine to
run for one hour. Notice that the light on the sensor
panel has now moved to the 1H location (G) Fig. 8B.
When the “TIME” button is pressed a third time, the
machine will run for two hours. At this point, the green
light will show up under the two hour location (H). When
you press the “TIME” button the fourth time, the unit will
run for four hours. Notice that the indicator light (J)
glows at the four hour mark.

All of these functions can be manually controlled by
using the two buttons on the sensor panel (K) Fig. 8B.

A

D

C

B

G

F

E

The Delta 50-875 Air Cleaner can be used in

a. bench-top sanding applications.
b. circular saw applications.
c. dry wall applications.
d. shop cleaning applications.
e. floor sanding applications.
f. any other application where non-metallic dust is a factor.

NOTE: The air cleaner may produce a slight odor for the first few hours of operation due to the protective coating which
is applied to internal components. This odor will dissipate and should be disregarded.

IMPORTANT: Never operate the air cleaner without air filters in place.

OPERATION

CHANGING AND CLEANING FILTERS

The model 50-875 Air Cleaner has an “air flow” indicator (A) Fig. 9A located on the left side of the unit. To check the
filters, turn the unit “ON”. If the indicator points to “green” (B) Fig. 9A, the filters are clean. Clean (or change) the filters
when the indicator points to “red” (C) Fig. 9A as follows:

1. Turn the unit “OFF”.

2. Remove the outer first stage filter (A) Fig. 9B by lifting and pulling out on the bottom of the filter. Clean or replace
the first stage filter depending on its condition. Clean this filter in one of two ways: Use a shop vac to remove the
dust, or use compressed air (30 psi maximum) to blow the dust out of the filter. If you replace the outer filter, check
to see if the filter has an air flow arrow (A) Fig 9D. If so, point the arrow inward. If the filter does not have an air
flow arrow, install the filter either way.

MAINTENANCE

HJ

K

9

Compressed air can be dangerous. For operator safety, do not exceed an air pressure of 30
psi. Do not point the air nozzle toward yourself or anyone else. Always wear safety glasses
and a dust mask when using compressed air.

3. Replace the filter, turn the unit “ON”, and check the air flow indicator again.

4. If the air flow indicator points to “green”, the inner filter is still useable. If the indicator points to “red”, remove the

outer filter, then remove the inner filter (B) Fig. 9C by lifting and pulling out on the bottom of the filter. DO NOT

try

to clean the inner filter. It is disposable and must be replaced.

5. After replacing the inner filter, reinstall the outer filter.

Fig. 9C

Fig. 9A

Fig. 9B

Fig. 9D

A

C

B

A

B

A

10

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and
Delta Authorized Service Stations. Please visit our Web Site

www.deltamachinery.com for a catalog or for the

name of your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use of
such accessories could be hazardous. For

safest operation, only Delta recommended accessories

should be used with this product.

ACCESSORIES

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE

•

DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,

Contractor’s Saw II™, Delta

®

, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,

Grip Vac™, Homecraft

®

, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,

MORTEN™, NETWORK™, OMNIJIG

®

, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-

CABLE

®

PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),

QUICKSET™, QUICKSET II

®

, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW

BOSS

®

, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber

Company

®

&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,

TORQBUSTER

®

, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,

Univise

®

, Versa-Feeder®, VERSA-PLANE®, WHISPER SERIES®, WOODWORKER’S CHOICE™.

Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.

PORTER-CABLE • DELTA SERVICE CENTERS

(CENTROS DE SERVICIO DE PORTER-CABLE

• DELTA)

Parts and Repair Service for Porter-Cable •Delta Machinery are Available at These Locations

(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable

•

Delta)

Authorized Service Stations are located in many large cities. Telephone [phone] or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable

·

Delta Distributor, Authorized

Service Center, or Porter-Cable

·

Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will

be directed to the nearest Porter-Cable

·

Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas

grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable

·

Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro

de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable

·

Delta. Si no tiene acceso a ninguna de estas opciones, llame al

800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.

ARIZONA

Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: [phone]
Fax: [phone]

CALIFORNIA

Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: [phone]
Fax: [phone]

San Diego 92111
7638 Clairemnot Blvd.
Phone: [phone]
Fax: [phone]

San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: [phone]
Fax: [phone]

COLORADO

Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: [phone]
Fax: [phone]

FLORIDA

Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: [phone]
Fax: [phone]

Tampa 33609
4538 W. Kennedy Boulevard
Phone: [phone]
Fax: [phone]

GEORGIA

Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: [phone]
Fax: [phone]

ILLINOIS

Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: [phone]
Fax: [phone]

Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: [phone]
Fax: [phone]

MARYLAND

Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: [phone]
Fax: [phone]

MASSACHUSETTS

Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: [phone]
Fax: [phone]

MICHIGAN

Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: [phone]
Fax: [phone]

MINNESOTA

Minneapolis 55429
5522 Lakeland Avenue North
Phone: [phone]
Fax: [phone]

MISSOURI

North Kansas City 64116
1141 Swift Avenue
Phone: [phone]
Fax: [phone]

St. Louis 63119
7574 Watson Road
Phone: [phone]
Fax: [phone]

NEW YORK

Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: [phone]
Fax: [phone]

NORTH CAROLINA

Charlotte 28270
9129 Monroe Road, Suite 115
Phone: [phone]
Fax: [phone]

OHIO

Columbus 43214
4560 Indianola Avenue
Phone: [phone]
Fax: [phone]

Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: [phone]
Fax: [phone]

OREGON

Portland 97230
4916 NE 122 nd Ave.
Phone: [phone]
Fax: [phone]

PENNSYLVANIA

Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: [phone]
Fax: [phone]

TEXAS

Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: [phone]
Fax: [phone]

Houston 77043
4321 Sam Houston Parkway,
West
Suite 180
Phone: [phone]
Fax: [phone]

WASHINGTON

Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: [phone]
Fax: [phone]

Printed in U.S.A. PC-0104-149

CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS

ALBERTA

Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: [phone]
Fax: [phone]

BRITISH COLUMBIA

8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: [phone]
Fax: [phone]

MANITOBA

1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
Phone: [phone]
Fax: [phone]

ONTARIO

505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: [phone]
Fax: [phone]

QUÉBEC

1515 ave.
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: [phone]
Fax: [phone]

1447, Begin
St-Laurent, (Montréal),
Québec
H4R 1V8
Phone: [phone]
Fax: [phone]