DELSOL DSSB1D, DSSB2, DSSB1F Installation, Use & Care Manual

DSSB1D

DSSB2

DSSB1F

MODEL:

PN 18917B 10/15

DELSOL SIDE BURNER

INSTALLATION, USE & CARE MANUAL

A special message…

Congratulations on your purchase of DELSOL Side Burner. DELSOL is

committed to making outdoor cooking products you’ll be proud to own for years.

This manual gives you easy to follow instructions for installing, operating and
maintaining your DELSOL product. We recommend reading this manual carefully
before your first use to ensure safety, proper care and operation. Keep this manual in

a safe place for future reference.

Thank you and welcome!

DELSOL

____________________________________________________________________

FOR YOUR RECORDS

Please record the following information and refer to them when contacting the

company or an authorized service agent. This information is found on the data

nameplate, located on the inside right hand panel of the side burner or underside of

top panel.

Model #: ________________________________

Serial #: _________________________________

Date of Purchase: __________________________

Place of Purchase: __________________________

Type of Gas: NG LP

To the Installer: Please read these instructions completely before installation and give this

manual to the owner.

To the Owner: Keep this manual in a safe place for future reference.

IMPORTANT SAFETY INFORMATION

D A N G E R

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.

D A N G E R

S’il y a une odeur de gaz:

1. Coupez l’admission de gaz de l’appariel.

2. Éteindre toute flamme nue.

3. Si l’odeur continue, évite l’appareil et appelle

tout de suite votre fournisseur de gaz ou les
pompiers.

W A R N I NG

1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.

2. An LP cylinder not connected for use
shall not be stored in the vicinity of this or
any other appliance.

A V E R T I S S E M E N T

1. Ne pas entreposer ni utiliser de l’essence ni

d’autres vapeurs ou liquides inflammables
dans le voisinage de l’appareil, ni de tout

autre appareil.

2. Une bouteille de propane qui n’est pas
raccordée en vue de son utilisation, ne doit
pas être entreposée dans le voisinage de cet
appareil ou de tout autre appareil.

THIS IS FOR OUTDOOR USE ONLY:

If stored indoors, detach and leave L.P. cylinder

outdoors.

C’EST POUR UTILISATION à L’EXTéRIEUR

SEULEMENT:

Si l’appareil est entreposé à l’interieur, enlever

les bouteilles et les laisser à l’extérieur.

B E F O R E L I G H T I N G

1. Read instructions before lighting.

2. Open lid during lighting.

3. If ignition does not occur in 5 seconds,
turn the burner control(s) off, wait 5
minutes, and repeat the lighting
procedure.

A V A N T D ’ A L L U M E R

L ’ A P P A R E I L

1. Lisez les instructions avant d’allumer l’appareil.

2. Ouvrez le couvercle avant d’allumer l’appareil.

3. Si l’appareil ne s’allume pas en 5 secondes,
fermez le robinet du brûleur, attendez 5 minutes,
et procédez de nouveau à l’allumage.

WARNING! Read this manual carefully and completely before using your side burner to ensure proper
operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or other
injury.

GENERAL SAFETY REQUIREMENTS:

In Massachusetts: All gas products must be installed using a “Massachusetts” licensed plumber or

gasfitter. A “T” handle type manual gas valve must be installed in the gas supply line to this appliance.
This applies to permanently installed natural gas and propane installations. This does not apply to
propane portable installations using a 20 pound tank.

1. The installation of this appliance must conform with local codes or, in the absence of local codes,
either the National Fuel Gas Code, ANZI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code.

2. This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles and
/or boats.

3. This outdoor cooking gas appliance is intended for use outdoors and shall not be used in a building,
garage or any other enclosed area.

4. Minimum clearance of 12 inches from the back and sides of the unit to adjacent combustible
construction must be maintained. This outdoor cooking gas appliance shall not be located
under overhead-unprotected combustible construction.

5. The utilization of an external electrical source requires that when installed, this outdoor cooking gas
appliance must be electrically grounded in accordance with the local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA
C22.1. Keep any electrical supply cord, or the rotisserie motor cord and the fuel supply hose away
from any heated surfaces.

6. Keep your side burner in an area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.

7. DO NOT obstruct the flow of combustion and ventilation air to this appliance. Keep the ventilation
openings of the cylinder enclosure free and clear from debris.

8. Check all gas connections for leaks with soapy water solution and brush. Never use an open flame.
(Reference page 6 for leak test procedure).

9. Check flexible hoses for cuts and wear that may affect the safety before each use.

10. Never use the side burner in a windy area.

11. The pressure regulator and hose assembly supplied with the DELSOL Side Burner must be used.
Replacement pressure regulators and hose assemblies must be those specified by DELSOL.

12. CALIFORNIA PROPOSITION 65-WARNING: The burning of gas cooking fuel generates some by­products which are on the list of substances known by the State of California to cause cancer or
reproductive harm. California law requires businesses to warn customers of potential exposure to
such substances. To minimize exposure to these substances always operate this unit according to the
use and care manual, ensuring you provide good ventilation when cooking with gas.

GAS SAFETY REQUIREMENTS

Each appliance is set and tested at the factory for the type of gas supply to be used.
Identify the type of gas, either Natural Gas or LP gas and make sure that the marking on the data
plate (rating plate) matches the gas being supplied to the side burner. The data plate is located on
the inside right hand panel of the side burner or underside of top panel.

All gas connections should be made by a qualified technician and in accordance with
local codes and ordinances. The installation must conform with local codes or, in the absence of
local codes, with either the national Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA­B149.1, Natural Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code.

WARNING:

CHECK TO ENSURE THAT THE GAS SUPPLY HOSE DOES NOT COME IN

CONTACT WITH ANY HOT SURFACE OF THE SIDE BURNER.

NEVER CONNECT THE SIDE BURNER TO AN UNREGULATED GAS

SUPPLY.

L.P. GAS (LIQUIFIED PETROLEUM /PROPANE)

If your side burner is factory built for L.P., the regulator supplied is set for 11” water
column and is for use with L.P. gas only. The factory-recommended regulator and hose must be
used with a 20 lb. L.P. cylinder.

L.P. GAS SAFETY REQUIREMENT

The LP-gas supply cylinder must be constructed and marked in accordance with the
Specifications for LP-gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the
National Standards of Canada CAN/CSA-B339, Cylinders, Spheres and Tubes for the
Transportation of Dangerous Goods, and Commission, as applicable; and

1. Provided with a listed overfilling prevention device.

2. Provided with a cylinder connection device compatible with the connection for outdoor
cooking appliances.

It must be provided with a shut-off valve terminating in gas tank valve outlet. It must include
a collar to protect the cylinder valve. The cylinder supply system must be arranged for vapor
withdrawal.

Do not operate the side burner indoors or in any enclosed area. If the side burner is not in
use, the gas must be turned off at the supply cylinder. If the side burner is to be stored indoors,
disconnect the gas supply cylinder and leave the cylinder outdoors out of reach of children and
must not be stored in a building, garage or any other enclosed area.

LP GAS HOOK-UP

DELSOL side burner for the use of LP gas comes equipped with its own regulator, which

MUST NOT be removed. Install the factory-supplied hose and regulator assembly as shown.
Connect the 3/8” flare end of the hose to the side burner coupling using a ¾” open wrench. Do
not apply pipe sealant to the 3/
tighten it, do not use a wrench. Check for leaks using soapy water solution. (Reference page 6
for leak test procedure).

Note: An enclosure for LP gas cylinder must be vented on the level of the cylinder valve and at

floor level. The effectiveness of the opening(s) for purposes of ventilation shall be determined
with the LP gas supply cylinder in place. This shall be accomplished by one of the following:

a. One side of the enclosure shall be fully open; or

b. For an enclosure having four sides, a top and a bottom:

1. At least two ventilation openings at cylinder valve level shall be provided in the

sidewall, equally sized, spaced at 180 degrees (3.14 rad), and unobstructed. Each
opening shall have a total free area of not less than 1/2 square inch per pound

” flare connection. Connect the regulator to the LP cylinder hand

8

(7.1 cm2/kg) of stored fuel capacity and not less than a total free area of 10
square inches (64.5 cm2).

2. Ventilation opening(s) shall be provided at floor level and shall have a total free

area of not less than ½" square inch per pound (7.1 cm2/kg) of stored fuel
capacity and not less than a total free area of 10 square inches (64.5 cm2). If

ventilation openings at floor level are in a sidewall, there shall be at least two
openings. The bottom of the openings shall be at floor level and the upper edge no
more than 5 inches (127 mm) above the floor. The openings shall be equally sized,
spaced at 180 degrees (3.14 rad) and unobstructed.

PORTABLE LP CONNECTION

! WARNING !

DO NOT STORE SPARE LP-GAS CYLINDER UNDER OR NEAR THIS APPLIANCE.

NEVER FILL THE CYLINDER BEYOND 80 PERCENT FULL.

FAILURE TO DO SO, A FIRE CAUSING DEATH OR SERIOUS INJURY MAY

OCCUR.

Typical Freestanding side burner gas hookup

T Adapter

(3/8” Threaded)

 NOTE: USE ONLY A 20-LBS. (5-GALLON CAPACITY) GAS CYLINDER.
 WARNING: DO NOT PLACE MORE THAN ONE CYLINDER IN THE CABINET

ENCLOSURE AT ANY TIME.

 WARNING: DO NOT USE A DENTED OR RUSTED LP CYLINDER.
 NEVER USE A CYLINDER WITH A DAMAGED VALVE.
 ALWAYS CHECK FOR LEAKS AFTER CHANGING THE LP CYLINDER. (Page 6)
 THE HIGH PRESSURE LP REGULATOR (SOLD SEPARATELY) MUST BE USED

WITHOUT ALTERATION.

DELSOL side burners for the use of LP gas
comes equipped with its own regulator, which

MUST NOT be removed.

1) To install the gas cylinder, place the cylinder

onto the provided location.

2) Check to ensure that the tank’s gas valve on

top of the cylinder is closed.

3) Connect the 3/8” flare end of the hose to the

grill coupling using a ¾” open Wrench. Do

not apply pipe sealant to the 3/

connection.

4) Connect the LP regulator to the cylinder and

hand-tighten only. Open the tank valve and

make sure all connections are leak tight using

a soapy water solution and a brush.

(Reference page 6 for leak test procedure).

” flare

8

NATURAL GAS INSTALLATION

PLASTIC INSERT

PLASTIC INSERT

SETTING UP FOR LP

BEFORE (SET FOR NG)

The installation must conform with local codes or, in the absence of local codes, with
either the national Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code.

1. This gas appliance and its individual shutoff valve must be disconnected from the gas supply

2. This appliance must be isolated from the gas supply piping system by closing its individual

water column. The regulator is convertible to 10” water column for plumb-in system LP
application. Do not use with a 20-lb LP cylinder. Make sure that the regulator is set for the
correct gas type. To check, remove the brass hex cap. You will find the conversion plastic pin
attached to the cap to the underside of the cap.

Natural Gas. If the disc is at the tip of the pin, away from the brass cap, the regulator is set for
system LP application. To convert to Natural Gas, remove the plastic conversion pin and invert
and replace it back in a manner such that the disc is close to the brass cap. For both Natural and
LP, the maximum inlet pressure is 14” water column.

piping system during any pressure testing of that system at the test pressures in excess of 1/2
psi (3.5 kPa).

manual shutoff valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psi (3.5 kPa).

If the gas side burner is factory built for Natural Gas, the regulator supplied is set for 4”

If the disc (1/2 in. diameter) of the pin is close to the cap, then the regulator is set for

NATURAL GAS INSTALLATION

A typical Natural Gas installation is shown below. Make sure that the factory-supplied
regulator is used and installed with the arrow mark on the regulator pointing towards the side
burner. Do not use any replacement regulator other than that specified by DELSOL. Use only
pipe sealants that are approved for use with Natural and LP gases. An installer-supplied gas
shutoff valve must be installed in an accessible location.

LEAK TEST

CAUTION BEFORE TESTING

 Finding and/or fixing a gas leak is NOT a “DO-IT-YOURSELF” procedure.
 NEVER USE THE SIDE BURNER WITHOUT FIRST LEAK TESTING THE GAS

CONNECTIONS.

 WARNING: DO NOT USE OPEN FLAME TO CHECK FOR LEAKS. USE OF AN OPEN

FLAME COULD RESULT IN A FIRE, EXPLOSION, BODILY HARM OR DEATH.

 DO NOT SMOKE WHILE PERFORMING THE LEAK TEST!
 To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area

while performing a leak test. Perform leak test outdoors only.

 Check to ensure that flexible hoses do not have any cuts and wear that may affect the safety

before each use. Only the factory supplied hose and regulator must be used. Use only
replacement regulator and hose assemblies specified by DELSOL.

LEAK TEST

1) Prepare a leak testing solution of sudsy water by mixing in a spray bottle with half liquid

soap and half water.

2) Confirm that all control knobs are in the OFF position.

3) Turn the main gas valve supply ON.

4) Apply leak testing solution by spraying on the pipe joints, fittings, and hose.

5) A gas leak is detected if;

a) there is a faint gas smell and/or…
b) …growing bubbles appear on any of the connection points and/or hose, DO NOT attempt

to ignite the side burner and IMMEDIATELY turn off the gas supply valve.

6) When there is a gas leak, call a qualified service technician. DO NOT use the side burner

until the leak is corrected.

LOCATING THE SIDE BURNER – DELSOL SIDE BURNER

NON-COMBUSTIBLE INSTALLATION ONLY

This gas appliance is designed and certified for outdoor use only. Do not locate this side
burner under overhead combustible surfaces. Do not operate the side burner inside a building,
garage, recreation vehicle or any enclosed area. When choosing an area, consider exposure to
wind, proximity to traffic paths and length of gas supply line. Keep gas supply lines as short as
possible to reduce pressure drop. Keep the side burner away from windy area but keep the side
burner in a well-ventilated area. Do not obstruct the flow of combustion and ventilation air
around the side burner. The supporting edges of the side burner must be located level and flat.
The counter should also be leveled. Ensure that the appliance remains at a distance of at least 12”
from any combustible material such as wood, gyprock, paper and plants. Do not store
combustible materials, gasoline or flammable liquids or vapors around the appliance.

CLEARANCE TO COMBUSTIBLE CONSTRUCTION

A minimum clearance of 12” from the sides and 12” from the back of the side burner to adjacent
vertical combustible construction must be maintained.

DÉGAGEMENT DE TOUTE CONSTRUCTION COMBUSTIBLE
Il faut maintenir une distance minimum de 12 po (30.48 cm) sur les côtés et de 12 po (30.48 cm)
sur l’arrière du gril par rapport aux constructions combustibles verticales adjacentes.

CLEARANCE TO NONCOMBUSTIBLE CONSTRUCTION

A minimum clearance of 5 1/2” from the back of the side burner above cooking surface to
non-combustible construction is required to allow the side burner hood to open completely.
A minimum of 6” clearance to the sides of the side burner above cooking surface to non­combustible construction is recommended. The side burner can be installed directly next to non­combustible construction below the cooking surface.

DÉGAGEMENT DE TOUTE CONSTRUCTION INCOMBUSTIBLE

Une distance minimum de 5 1/2 po (13.97 cm) de l’arrière du gril au-dessus de toute surface de
cuisson à la construction incombustible est prescrite pour permettre à la hotte d’ouvrir
complètement. Une distance minimum de 6 po (15.24 cm) des côtés du gril au-dessus de la
surface de cuisson à la construction incombustible est recommandée. Le gril peut être installé
directement à proximité d’une construction incombustible en-dessous de la surface de cuisson.

CUT-OUT DIMENSIONS – DELSOL SIDE BURNER

.

OPERATING INSTRUCTIONS

BEFORE LIGHTING THE SIDE BURNER

 DO NOT ATTEMPT TO LIGHT THE SIDE BURNER IF YOU SMELL GAS.
 WARNING! IT IS CRITICAL THAT THE BURNERS ARE PROPERLY

INSTALLED WITH THEIR ORIFICES. If not properly installed, it could lead to fire,
potential damage to your side burner, bodily injury or death.

 Inspect the gas supply piping or hose prior to turning the gas ON. If there is evidence of cuts,

wear, or abrasion, it must be replaced prior to use. The replacement pressure regulator and
hose assembly must be the type specified by the manufacturer. Do not use the side burner if
the odor of gas is present. The pressure regulator and hose assembly supplied with the units
must be used.

 If the unit is LP, screw the regulator and hand tighten to the valve of the cylinder and leak

check the hose and regulator connections with a soap and water solution before operating the
unit. Reference page 6 for leak test procedure.

 Always keep your face and body as far away as possible when lighting.
 Refer to spiders and insects warning and procedure under the cleaning and maintenance page

of this manual

LIGHTING THE BURNERS

1. Make sure all knobs are in the “OFF” position.

2. Turn “on” the gas at source. Caution: If you smell gas, shut off gas

supply and call for service.

3. Before lighting, remove the side burner cover or any cooking

utensils from the burner grate.

4. To ignite burners, push the burner knob in and slowly rotate counter

clockwise to the high position. A loud click can be heard as the
electronic lighter produces a spark. Listen for the sound of the gas
igniting and look for the flame through the cooking grids. If the
burner does not light on the first try, repeat immediately.

5. If the burner does not ignite within 5 seconds, turn the burner to

“OFF” and wait for five minutes. Repeat the above procedures or try

the following manual lighting procedures
a. Hold a lit match next to the burner ports
b. Push and turn the burner knob counterclockwise to ignite the

burner.

6. Caution: Do not leave the side burner unattended while cooking.

7. To shut down the burner, push and turn the burner knob clockwise to “OFF”.

8. For complete shutdown, turn “off” the gas at source.

OPERATING INSTRUCTIONS

SPIDER AND INSECT WARNING

Spiders and other insects can nest in the burners of this and any other side burners,
which causes the gas to flow from the front of the burner. This dangerous “condition” can
cause a fire behind the valve panel, damaging the side burner and making the side burner
unsafe to operate. Inspect the burners once a year or if the side burner has not been used for
more than one month or if any of the following conditions occur:

1) The smell of gas in conjunction with the burner flames appearing yellow.

2) The side burner does not reach temperature.

3) The side burner heats unevenly.

4) The burners make popping noises.

MATCH LIGHTING INSTRUCTIONS:

If spark igniter will not light the burners, the burners can be lit manually using a lit long match,
taper or BBQ lighter.

1. Push and turn the knob counter-clock-wise to the biggest flame marking on the bezel.

2. Insert a lit match or BBQ lighter thru the grates and near the top of the burner. Once you

see or hear a flame you can release the knob.

Important: If burner fails to light within 4 seconds, turn off gas and wait 5 minutes before
repeating the process.
Warning: If you smell gas, shutoff the gas supply and immediately check for leaks using the
soapy water technique. (See Page 6)

CLEANING & MAINTENANCE

STAINLESS STEEL

The DELSOL Side Burner is made of all welded stainless steel. It is non-rusting and non­magnetic. Never clean the stainless steel when it is hot. After the initial use, certain areas of the
side burner may discolor. This is a normal discoloration caused by the intense heat given off by
the burners. Specks of grease can gather on the surface of the stainless steel and get baked-on.
These can be removed by using a mild abrasive pad (like Scotch Brite) with a stainless steel
cleaner. Use the mildest cleaner and always scrub in the direction of the grain.

Do not use steel wool to clean the side burner. Do not use abrasives on the polished
highlights. Be extra careful when cleaning around the highlights. Metal polisher or mild chrome
cleaner can be used to bring back the luster on highlights. To touch-up minor scratches in the
stainless steel, sand the affected surface very lightly, with 100-dry grit emery sandpaper in the
direction of the grain.

EXPLODED VIEW – DSSB1D

SERVICE PARTS LIST – DSSB1D

Number

Part Number

Description

QTY.

1

S23175

TOP COVER, 1 BURNER.

1

2

S13908

GRATE, 9 X 9

1

3

S13197

DELSOL KNOB

1

4

S13215

KNOB BEZEL

1

5

S13196

DELSOL LOGO

1

6

S13376

UPPER BURNER

1

7

S13377

LOWER BURNER

1

8

S16000

WIRE, IGNITER, 10"

1

9

S12677

3/8 FLARE ½ FIP 90 DEG ELBOW COUPLING

1

10

S12618

½ CLOSE NPT NIPPLE

1

11

S15351

REGULATOR NG/LP

1

12

S12758

PIPE MANIFOLD SIDE BURNER, SINGLE

1

13

S15150

BURNER VALVE WITH FLAME THROWER

1

14

S12418

3/8 X 10” FLEX TUBING W/ BRASS FLARE NUTS 1 NON SHOWN PARTS

S15148-60

ORIFICE, #60 LP

1

S15148-53

ORIFICE, #53 NG

1

EXPLODED VIEW – DSSB2

SERVICE PARTS LIST – DSSB2

Number

Part Number

Description

QTY.

1

S23163

TOP COVER, 2 BURNER

1

2

S13908

GRATE, 9 X 9

2

3

S13376

UPPER BURNER

2

4

S13377

LOWER BURNER

2

5

S23159

STIFFENER, SIDE BURNER

1

6

S12677

3/8 FLARE ½ FIP 90 DEG ELBOW COUPLING

1

7

S15351

REGULATOR NG/LP

1

8

S12618

½ CLOSE NPT NIPPLE

1

9

S12757

PIPE MANIFOLD SIDE BURNER, DOUBLE

1

10

S23165Y

FRONT PANEL

1

11

S13197

DELSOL KNOB

2

12

S13215

KNOB BEZEL

2

13

S13196

DELSOL LOGO

1

14

S15150

BURNER VALVE WITH FLAME THROWER

2

15

S16000

WIRE, IGNITER, 10"

1

16

S16001

WIRE, IGNITER, 15"

1

17

S12418

3/8 X 10” FLEX TUBING W/ BRASS FLARE NUTS

1

18

S12419

3/8 X 15” FLEX TUBING W/ BRASS FLARE NUTS 1 NON SHOWN PARTS

S15148-60

ORIFICE, #60 LP

2

S15148-53

ORIFICE, #53 NG

2

EXPLODED VIEW – DSSB1F

SERVICE PARTS LIST – DSSB1F

Number

Part Number

Description

QTY.

1

S23175

TOP COVER, 1 BURNER

1

2

S13908

GRATE, 9 X 9

1

3

S13376

UPPER BURNER

1

4

S13377

LOWER BURNER

1

5

S13197

DELSOL KNOB

1

6

S13215

KNOB BEZEL

1

7

S23174

MANIFOLD MOUNTING BRACKET

1

8

S12418

3/8 X 10” FLEX TUBING W/ BRASS FLARE NUTS

1

9

S12758

MANIFOLD PIPE, SINGLE

1

10

S15150

BURNER VALVE W/ FLAME THROWER

1

11

S15351

REGULATOR NG/LP

1

12

S12618

½ CLOSE NPT NIPPLE

1

13

S12677

3/8 FLARE ½ FIP 90 DEG ELBOW COUPLING

1

14

S16000

WIRE IGNITER, 10”

1

NON SHOWN PARTS

S15148-60

ORIFICE, #60 LP

1

S15148-53

ORIFICE, #53 NG

1

DELSOL WARRANTY

ONE-YEAR FULL WARRANTY: DELSOL warrants the outdoor Side Burners and all of their component parts,

to be free from defects in materials and workmanship under normal residential
use for a period of one year from the original date of purchase. DELSOL will
repair or replace, at its option, any part, which fail or is found to be defective
during the warranty period. The actual part will be repaired or replaced, free
of charge, with the owner paying for all other costs including labor,
installation, shipping and handling charges.

WARRANTY LIMITATIONS & EXCLUSIONS

This warranty shall apply only to the products purchased and located in the continental United States and Canada.
The warranty coverage begins on the original date of purchase and proof of date of purchase is required. In order to
activate the warranty, we require that you send in the attached warranty registration. This warranty applies only to
the original owner and may not be transferred.

This warranty does not apply to damages resulting from negligence, alteration, misuse, abuse, accident, natural
disaster, improper installation or improper operation, unauthorized adjustments or calibrations, dings, dents,
scratches, or damages due to harsh cleaning chemicals. This warranty does not apply to rust, corrosion,
discoloration, surface scratches, weather and atmospheric related staining and oxidation which are normal conditions
and to be expected with any outdoor products unless the affected component becomes inoperable. This warranty
does not apply to commercial use, or to products with altered or removed serial numbers. DELSOL shall not be
liable for incidental, consequential, special or contingent damages resulting from its breach of this written warranty
or any implied warranty.

WARRANTY SERVICE & REPLACEMENT PARTS: Call your authorized selling dealer or call DELSOL
directly at 800-789-2206 or 562-802-3488. Be prepared to furnish the following information: Purchaser’s name,
model and serial number of the appliance, date of purchase and the accurate description of the problem. DELSOL
will not pay for service calls for correcting an installation problem. Owner shall be responsible for proper
installation, providing normal care and maintenance, providing proof of purchase upon request and making the
appliance accessible for service. In the event of any warranty replacement, all removal, replacement, installation and
shipping costs are the responsibility of the side burner owner.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusions of or limitations on
consequential damages. This warranty gives you specific legal rights and you may have other rights, which vary
from state to state.

Customer Name

Model #

Address

Serial #

City

Date Purchased

Zip

Dealer’s Name

Phone #

Dealer’s Address

e-mail:

Cut
Here

HOW TO OBTAIN SERVICE

For service, please contact your DELSOL dealer or call DELSOL direct at [phone] or
[phone] or fax [phone]

Mailing address:
DELSOL Grill
13259 East 166th Street
Cerritos, CA 90703

Please provide:

 Model number
 Serial Number
 Date of installation
 A description of the problem

Warranty Registration

This Warranty Registration card must be returned within thirty days of purchased to properly activate

your warranty. This information is for our internal use only.

Place

Postage

Here

Cut
Here

Customer Service

ATTN: Warranty Department

13259 East 166th Street

Cerritos, CA 90703

Fax no. [phone]