CORDLESS KETTLE
23456
EN
Max water level
indicator
ON/OFF switch
Filter
Twin power-on
indicator lights
Removable lid
Plug
Kettle body
360° base with cord
storage
Description of Appliance
7
Thank you for c hoosing this De’Longhi kettle. To get the best results from you r new kettle, read these
instructions carefu lly and retain for f uture reference. This is the only way to ensure optimum resu lts
and max
imum safety.
Safety Warnings
Please read these instructions before operating and retain for future reference.
• Ensure that your mains supply voltage is the same as that marked on the underside of your kettle.
• To protect against electrical hazards do not immerse the mains lead, plug power base or kettle in water or any other liquid. Do not use in the bathroom or near any source of water. Do not use outdoors.
• Do not touch hot surfaces i.e. body or lid. Use handles or knobs.
• Do not remove the lid while the kettle is boiling.
• Take care when pouring - do not over-tilt the kettle as water may enter into the switch mechanism.
• Water can remain hot for a long time after boiling and can present a scald hazard. Keep the kettle and the mains lead
away from the edge of the work surface and out of the reach of children.
• Do not allow the mains lead to hang over the edge of the table or work surface.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the
appliance.
• Remove the plug from the mains socket when not in use and before cleaning. Allow the kettle to cool before cleaning.
• Remove the kettle from its power base before filling.
• Avoid contact with steam coming out of the spout when pouring, and out of the lid or spout when refilling.
• Cau tion: Do not operate the kettle on an inclined surface.
• Never move the kettle while it is in use.
• Do not use the kettle if you have wet hands.
• Keep the kettle, the power base, and the mains lead away from hotplates, hobs or burners.
• Do not use the kettle for any purpose other than heating water.
• De’Longhi will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions
• Do not place any utensils into the kettle. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury.
• Never use the kettle without its lid.
• Position the kettle properly on the power base before switching on.
• Use the kettle only with the power base supplied (and vice versa).
• Do not operate this kettle if the mains lead or plug is damaged, if the kettle malfunctions, or has been damaged in any
manner. It must be returned to an authorised service agent for repair or replacement in order to avoid hazard.
• The power cable must not be replaced by the user as this requires the use of special tools. If the supply cord is damaged,
it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• If the kettle is overfilled, boiling water may overflow.
Materials and accessories coming into contact with food conform to EC regulation 1935/2004.
8
Using for t he first time
• Before use, check that the appliance has not been damaged during transport.
• Remove all packaging from the kettle and power base.
• Remove any labels from the outer surfaces except the rating label.
• Remove the filter (fig. 1) and wash it with water (fig. 2) (refer to page 5 “Removing the
scale filter”).
• Fill the kettle to the max level and boil.
• The boiled water should be discarded and the kettle rinsed out with cold water. This procedure should be carried out twice to remove any manufacturing dust, etc.
• After the kettle has been rinsed out, refit the filter (fig. 3).
Using th e kettle
With the specially designed power base and central connector, you can now set the kettle
on the base at any angle, from any position.
• Release cord from storage base and adjust length by winding around the base to give the
correct cord length to reach the plug socket to be used (fig. 4).
• Do not leave loose cord hanging over the edge of work surfaces.
Filling
• Remove the kettle from the base unit before filling.
• Remove the lid and fill the kettle to the desired level.
Do not fill with less than 0,3 litre of water (min level) to prevent the kettle running dry while in use; misuse of this kind will shorten the life of the element.
Do not fill with more than 1,7 litres of water (max. level).
If the kettle is o verfilled, there is a
risk th at boiling water may overflow
and cause burns.
• To close the lid, push it onto the kettle body until it clicks firmly into place.
• The water level indicator enables you to see the quantity of water in the kettle.
Switching on
• Plug the power base into the mains socket.
• Place the kettle on the power base.
• Press the ON/OFF switch down (fig.5) to switch the kettle on.
• The power-on indicator lights will illuminate.
• The kettle will automatically switch off once the water is boiled (the ON/OFF switch will
click upwards and the lights will switch off ).
• To turn the kettle off before the water boils, you may move the ON/OFF switch up to the
OFF position, or simply lift the kettle from its base - it will switch off and the switch will return to the
OFF position automatically.
Pou ring
• Remove the kettle from the power base and carefully pour out the water. Do not tilt the
kettle suddenly or pour water out at too sharp an angle.
• When you lift the kettle from the base, you may see moisture on the top surface of the
base. Condensation on the base is perfectly normal, and should not be a cause for alarm.
Safety dev ices
1) Autom atic ON/OFF switch
Your kettle is fitted with an ON/OFF switch which automatically switches off once the water has boiled. If the kettle has
1
2
CORD EXIT
Fig.1
Fig.2
Fig.3
Fig.4
a
c
b
Fig.5
9
just boiled, wait a minute or so before re-boiling the kettle. Do not attempt to hold the ON/OFF switch in the “on” position or adjust the switch mechanism.
2) Safety cu t-out
If the kettle is switched ON with too little or no water, it is protected against damage by a safety cut-out device which
will switch off the power.
If this cut-out operates, disconnect the kettle from the mains supply and leave to cool down before refilling with cold
water (otherwise the element could be damaged). It will reset automatically when cooled down.
3) If the kettle is lifted from base while operating (ON), it will automatically switch off.
Cleaning and maintenance
Cleaning th e kettle
• Allow the kettle to cool down fully and disconnect the appliance from the mains before cleaning.
• Do not immerse the kettle or base in water.
• Use a soft dampened cloth to wipe the outside of the kettle and dry with a soft, dry cloth.
• DO NOT use harsh scouring agents.
• Ensure that all electrical connectors and sockets are kept dry.
Scale
Scale is mainly calcium carbonate (chalk), a harmless, naturally occurring mineral found in most water supplies. “Hard”
water contains more of this mineral than “soft” water.
When the water is heated, the minerals in the water solidify, making the water appear cloudy. These minerals form a thin
film on the walls, element and on the surface of the water. The water may look like it has white coloured pieces of plastic
floating on the surface. On traditional kettle elements, scale forms a hard white “crust” which adversely affects performance
and reduces the life of the element. As soon as you notice a film forming on the water, or on the interior walls of the kettle,
simply rinse the kettle and wipe it out.
Scale filter
Your kettle is fitted with a scale filter to prevent loose particles of scale being poured into your beverage. This filter is both
removable and washable. The frequency with which you will need to clean any scale deposits from your filter will depend on
the hardness of water in your area and how often you use the kettle.
You should remove and clean the water filter when you notice any deposits being left on the filter or if the pouring efficiency
is impaired.
Rem oving the scale filter
• Allow the kettle to cool down fully.
• Disconnect the appliance from the mains electrical supply.
• Make sure that your hands are clean and free from soap, etc or anything which might taint the water.
• Empty the kettle and remove the lid. Remove the filter by pushing the catch firmly from inside the kettle, then lift up
(fig. 1).
• Rinse under a tap while brushing with a soft brush (fig. 2).
• Replace the filter sliding it firmly down (fig. 3).
Descaling
It is vital to clean and descale the kettle and filter regularly in order to maintain it in good working order. Failure to descale
your kettle may invalidate your guarantee.
• It is recommended to use specific (store bought) products for descaling of kettles.
• When limescale starts to build up on the heating element, buy a suitable descaler and descale your kettle. After descaling, boil with fresh water several times and discard. Clean any descaler off the kettle – it can damage the parts.
• If the filter requires descaling, remove the filter and place into the kettle whilst descaling.
• Ensure that the electrical connections are completely dry before using the kettle.
1771031IDL/10.10
De’ Longhi Appliances via Seitz, 47 - 31100 - Treviso - Italia
Loading...