Delonghi DEP7410P User Manual

DE’LONGHI

COOKING

INSTALLATION and SERVICE INSTRUCTIONS USE and CARE INSTRUCTIONS

DEP7410P

MULTIFUNCTION PYROLYTIC OVEN

distributed by

DeLonghi Australia Pty Ltd DeLonghi New Zealand Ltd

Dear Customer,

Thank you for having purchased and given your preference

to our product.

The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance.

Please keep this booklet in a safe place. It may be useful in future, either to yourself or to others in the event that doubts should arise relating to its operation.

This appliance must be used only for the task it has explicitly been designed for, that is for cooking foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous.

The manufacturer declines all responsibility in the event of damage caused by improper, incorrect or illogical use of the appliance or be faulty installation.

This appliance has been designed and constructed in accordance with the following codes

and specications:

AS/NZS 60335.1 General Requirements for Domestic electrical appliances AS/NZS 60335.2.6 Particular Requirements for Domestic electrical cooking appliances AS/NZS CISPR 14.1 Electromagnetic Compatibility Requirements.

PRODUCT LABEL

IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS

IMPORTANT: This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non domestic environment i.e. a semi commercial, commercial or communal environment.

Read the instructions carefully before installing and using the appliance.

■ After having unpacked the appliance, check to ensure that it is

not damaged and that the oven door closes correctly.

 In case of doubt, do not use it and consult your supplier or a

professionally qualied technician.

■ Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should not be left around within easy reach of children, as these may cause serious injuries.

■ Some appliances are supplied with a protective lm on steel and

aluminium parts. This lm must be removed before using the

appliance.

■ IMPORTANT: The use of suitable protective clothing/gloves is

recommended when handling or cleaning this appliance.

■ Do not attempt to modify the technical characteristics of the appliance as this may become dangerous to use. The manufacturer declines all responsibility for any inconvenience resulting from the inobservance of this condition.

■ Do not operate your appliance by means of an external timer or separate remote-control system.

■ Do not carry out cleaning or maintenance operations on the appliance without having previously disconnected it from the electric power supply.

■ WARNING: Ensure that the appliance is switched off before

replacing the oven lamp to avoid the possibility of electric shock.

■ Do not use a steam cleaner because the moisture can get into the appliance therefore making it unsafe.

■ Do not touch the appliance with wet or damp hands (or feet).

■ Do not use the appliance whilst in bare feet.

■ If you should decide not to use this appliance any longer (or

decide to substitute another model), before disposing of it, it is recommended that it be made inoperative in an appropriate manner in accordance to health and environmental protection regulations, ensuring in particular that all potentially hazardous parts be made harmless, especially in relation to children who could play with unused appliances.

■ The various components of the appliance are recyclable. Dispose of them in accordance with the regulations in force in your country. If the appliance is to be scrapped, remove the power cord.

■ After use, ensure that the knobs are in the off position.

■ Children less than 8 years of age shall be kept away unless

continuously supervised.

■ This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

■ The manufacturer declines all liability for injury to persons or damage to property caused by incorrect or improper use of the appliance.

■ WARNING: During use the appliance and its accessible parts

become hot; they remain hot for some time after use.

– Care should be taken to avoid touching heating elements

inside the oven.

– The door is hot, use the handle.

– To avoid burns and scalds, young children should be kept

away.

■ Make sure that electrical cables connecting other appliances in the proximity of the oven cannot become entrapped in the oven door.

■ WARNING: When correctly installed, your product meets all

safety requirements laid down for this type of product category. However special care should be taken around the rear or the underneath of the appliance as these areas are not designed or intended to be touched and may contain sharp or rough edges, that may cause injury.

■ FIRST USE OF THE OVEN - it is advised to follow these instructions:

– Furnish the interior of the oven as described in the chapter

“CLEANING AND MAINTENANCE”.

– Switch on the empty oven on max to eliminate grease from the

heating elements.

– Disconnect the appliance from the electrical power supply, let

the oven cool down and clean the interior of the oven with a cloth soaked in water and neutral detergent; then dry carefully.

■ CAUTION: Do not use harsh abrasive cleaners or sharp metal

scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.

■ Do not line the oven walls with aluminium foil. Do not place baking trays or the drip tray on the base of the oven chamber.

■ FIRE RISK! Do not store ammable material in the oven.

■ Always use oven gloves when removing the shelves and food

trays from the oven whilst hot.

■ Do not hang towels, dishcloths or other items on the appliance or its handle – as this could be a re hazard.

■ Clean the oven regularly and do not allow fat or oils to build up in the oven base or tray. Remove spillages as soon as they occur.

■ Do not stand on the open oven door.

■ Always stand back from the appliance when opening the oven

door to allow steam and hot air to escape before removing the food.

■ SAFE FOOD HANDLING: Leave food in the oven for as short

a time as possible before and after cooking. This is to avoid contamination by organisms which may cause food poisoning. Take particular care during warmer weather.

■ WARNING: Take care NOT to lift the appliance by the door

handle.

■ PYROLYTYC SELF-CLEANING OVEN:

– Remove oven shelves, side racks (models with side racks

only) and all other accessories, bakeware, and utensils. If left in the oven, they will become permanently discoloured or damaged; items made from combustible materials (eg wood,

fabric, plastic) may even catch re.

– Wipe up any spills; excess spillage must be removed before

starting the self-cleaning cycle.

– During the pyrolytic cleaning function, please note that outside

surfaces may become hotter than usual. Please ensure children are kept away.

INSTALLATION

CAUTION:

■ This appliance must be installed in accordance with these installation instructions.

■ This appliance shall only be serviced by authorised personnel.

■ This appliance is to be installed only by an authorised person in compliance

with the current electrical regulations and in observation of the instructions supplied by the manufacturer.

 Failure to comply with this condition will render the guarantee invalid.

■ Incorrect installation, for which the manufacturer accepts no responsibility, may

cause personal injury of damage.

■ Always disconnect the appliance from mains power supply before carrying out

any maintenance operations or repairs.

FITTING REQUIREMENTS

■ The oven can be tted in standard units, 60 cm width and depth.

■ Installation requires a compartment as illustrated in gures 1 and 2.

■ On the lower side, the oven must lay on supports standing the oven weight.

■ Remember the housing should not be free standing but be secured to the wall and/or

adjacent ttings.

■ We would point out that the adhesive which bonds the plastic laminate to the

furniture must withstand temperatures not less than 150° C to avoid delamination.

■ The walls of the units must be capable of resisting temperatures of 75 °C above

room temperature.

■ Do not seal the oven into the cabinetry with silicone or glue; this makes future

servicing difcult. Delonghi will not cover the costs of removing the oven, or of

damage caused by this removal.

■ The walls surrounding the oven must be made of heat-resistant material.

■ WARNING: Taking care NOT to lift the oven by the door handle.

WARNING When correctly installed, your product meets all safety requirements laid down for this type of product category. However special care should be taken around the rear or the underneath of the appliance as these areas are not designed or intended to be touched and may contain sharp or rough edges, that may cause injury.

IMPORTANT Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage

caused by frequent or excessive condensation, we recommend moisture-proong

the oven cavity.

560

550 min

085

595

545

556

600

Figure 1

Figure 2

600

560

085

Figure 3

IMPORTANT:

When handling the oven, take care not to damage the door sensor lever “L” (near the top right corner of the oven seal).

FIXING THE OVEN

Introduce the oven into the furniture opening and x it with 2 screws (not supplied) as gure 4. Before xing the 2 screws, t the 2 plastic bushes (supplied with the appliance in a separate kit) into the xing holes. Take care to t the bushes in the correct way, they must lie at.

It is essential that the oven rests on a surface which will support its weight, as the screw

xing is only complementary.

Note:

It is essential that when installing your oven adequate air circulation is allowed for within

the installation. See gures 1, 2.

Inadequate air circulation may greatly impair the performance of your oven and may effect adjacent cabinets due to an increase in temperature.

Caution! Do not lift this oven by the door handle.

Adjust the hinges of furniture doors adjacent to the oven to allow a 4-5 mm gap between the furniture door and the oven fra me.

Figure 4

ELECTRICAL REQUIREMENTS

■ The appliance must be connected to the mains checking that the voltage corresponds to the value given in the rating plate and that the electrical cable sections can withstand

the load specied on the plate.

■ A suitable isolating switch providing full disconnection from the mains power supply shall be incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements).

■ The isolating switch shall be easily accessible to the customer with the oven installed.

■ If the electrical supply is restricted, means of all-pole disconnection must be accessible

and incorporated in the xed wiring in accordance with the wiring rules.

■ The power supply cable must not touch the hot parts and must be positioned so that it does not exceed 75°C above ambient.

■ The oven is supplied without a power supply plug and therefore if you are not connecting

directly to the mains, a standardized plug suitable for the load must be tted.

■ The plug must be connected to an earthed socket in compliance with safety standards.

■ To connect the appliance to the mains electricity supply, do not use adapters, reducers or branching devices as they can cause overheating and burning.

■ Once the appliance has been installed, the switch or socket must always be accessible.

■ If the supply cord is damaged it must be replaced by the manufacturer or it’s Service

Agent or a similarly qualied person in order to avoid a hazard.

N.B. The connection of the appliance to earth is mandatory.

If the installation requires alterations to the domestic electrical system call a qualied

electrician. He should also check that the domestic electrical system is suitable for the power drawn by the appliance.

Replacing the power cord must be done by a qualied electrician in accordance with

the instructions supplied by the manufacturer and in compliance with established electrical regulations.

REPLACING THE POWER SUPPLY CABLE

Important! This appliance must be connected to the electricity supply only by an authorised person.

To connect the supply cable:

”

■ Unhook the terminal board cover by inserting a screwdriver into the two hooks “A

(g.

5).

■ Unscrew the screw “D” and open completely the cable clamp “E” (g. 6).

■ Connect the phase, neutral and earth wires to terminal board “G” according to the

diagram in g. 7.

■ Strain the feeder cable and block it with cable clamp “E” (by screwing screw “D”).

■ Close the terminal block cover (check the two hooks “A” are correctly hooked).

N.B. The earth conductor must be left about 3 cm longer than the others.

VOLTAGE AND POWER CONSUMPTION

220-240 V ac 3050 W (13.26 A)

Figure 5

FEEDER CABLE SECTION TYPE H05RR-F

3 x 1,5 mm2 (*) (**)

(*) Connection possible with plug and outlet (**) Connection with wall box connection.

Figure 6

Figure 7

220-240 V ac

PENL

ELECTRIC DIAGRAM

Figure 8

USE AND CARE

Stop notch

Guard rail

CAUTION:

■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous.

■ Do NOT place combustible materials or products on this appliance at any time.

Figure 9a

OVEN FITTING OUT

Operate as follows:

■ Assemble the wire racks on the side oven walls sliding the rear prongs of each rack into the holes “A” at the

rear of the oven (g. 9a). Fit the side racks front tab over the xing point and tighten the xing screws.

■ Slide in the grease lter on the back of the oven as in g. 10.

■ Slide in, on the guides, the shelf (g. 9b).

 The rack must be tted so that the

safety notch, which stops it sliding out, faces the inside of the oven; the guard rail shall be at the back.

Oven tray

■ The oven tray must be correctly placed on the shaped wire shelf (not the at one)

or on the telescopic sliding shelf supports

(g. 9b, with the sliding supports not on

the third level from the bottom).

Figure 9b

GREASE FILTER

■ A special screen is provided at the back of the oven to catch grease particles, mainly when meat is being

roasted (g. 10).

■ Clean the lter after any cooking!

 The grease lter can be removed

for cleaning and should be washed

regularly in hot soapy water (g. 10).

■ Always dry the lter properly before tting it back into the oven.

CAUTION: When baking pastry etc. this

lter should be removed.

Figure 10

TELESCOPIC SLIDING SHELF SUPPORTS

The telescopic sliding shelf supports make it safer and easier to insert and remove the oven shelf and tray. They stop when they are pulled out to the maximum position.

Important! When tting the sliding shelf supports, make sure that you t:

■ The slides to the top wire of a rack. They do not t on the lower wire.

■ The slides so that they run out towards the oven door.

■ Both sides of each pair of shelf slides.

■ Both sides on the same level.

To x the sliding shelf support onto the side racks:

■ Screw the side racks onto the oven walls (g. 9a).

■ Fit the sliding shelf support onto the top wire of a rack and press (g. 11).

You will hear a click as the safety locks clip over the wire.

To remove the telescopic sliding shelf

supports:

■ Remove the side racks by unscrewing the xing screws (g. 12).

■ Lay down the telescopic sliding shelf support and side racks, with the telescopic sliding shelf support underneath.

■ Find the safety locks. These are the tabs that clip over the wire of the side

rack (arrow 1 in g. 13).

■ Pull the safety locks away from the wire to release the wire (arrow 2 in g. 13).

Cleaning the sliding shelf supports:

■ Wipe the supports with a damp cloth and a mild detergent only.

■ Do not wash them in the dishwasher, immerse in soapy water, or use oven cleaner on them.

Figure 11

Figure 12

Figure 13

+ 36 hidden pages