Delonghi DEGH70W Instructions
distributed by
DèLonghi
Pty Ltd
INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
BUILT-IN GAS
HOBS
Models: DEGH70W - DEGH70WF
2
Dear Customer,
Thank you for having purchased and given your
preference to our product.
The safety precautions and recommendations reported
below are for your own safety and that of others. They
will also provide a means by which to make full use of
the features offered by your appliance.
Please keep this booklet in a safe place. It may be
useful in future, either to yourself or to others in the
event that doubts should arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking
foodstuffs. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or
illogical use of the appliance or be faulty installation.
PRODUCT LABEL
3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR
USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental
rules. In particular:
■ Never touch the appliance with wet hands or feet;
■ do not operate the appliance barefooted;
■ do not allow children or other incapable people to use the appliance
without supervision.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or illogical use of the appliance.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified
technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should
not be left around within easy reach of children, as these may cause serious injuries.
■ Do not attempt to modify the technical characteristics of the appliance as this
may become dangerous to use.
■ Do not carry out cleaning or maintenance operations on the appliance without
having previously disconnected it from the electric power supply.
■ After use, ensure that the knobs are in off position.
■ Do not allow children or other incapable people to use the appliance without
supervision.
■ During and after use of the hob, certain parts will become very hot. Do not
touch hot parts.
■ Keep children away from the appliance when it is in use.
■ Some appliances are supplied with a protective film on steel and aluminium
parts. This film must be removed before using the appliance.
■ The manufacturer declines all liability for injury to persons or damage to proper-
ty caused by incorrect or improper use of the appliance.
4
INSTALLATION
CAUTION:
■ This appliance must be installed in accordance with these installation
instructions, local gas fitting regulations, municipal building codes, water
supply regulations, electrical wiring regulations, AS5601 / AG 601 - Gas
Installations and ony other relevant statutory regulations.
■ This appliance shall only be serviced by authorized personnel.
■ This appliance is to be installed only by an authorised person.
■ Incorrect installation, for which the manufacturer accepts no responsibility,
may cause personal injury of damage.
■ Always disconnect the appliance from mains power supply before carrying
out any maintenance operations or repairs.
■ In the room where the cooker is installed, there must be enough air to
allow the gas to burn correctly, according to the current local regulations.
5
480
70
60
0
– 2
560
200
0
– 2
200
120
90
Area for
electrical connection
Area for
gas connection
680
500
Figure 1
DIMENSIONS: (Note: Also refer to Figure 1 above)
General Dimensions
Width 680 mm
Depth 500 mm
Depth Below Mounting Surface 33,7 mm
Cut-out Dimensions
Width 560 mm
Depth 480 mm
0
–2
0
–2
6
Figure 2
CLEARANCES:
Installation clearances and protection of combustible surfaces shall comply with the
current local regulations e.g. AG 601 (AS 5601) - Gas Installations code.
Important note:
This appliance shall not be used as a space heater, especially if installed in marine
craft or caravans.
This cooktop has been designed and constructed in accordance with the following
codes and specifications:
AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances
AS/NZS 60335-1 General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NSZ 1044 Electromagnetic Compatibility Requirements.
450 mm
200 mm min
750 mm
60 mm min
500 mm
7
The installation shall comply with the dimensions in Figures 1 and 2, bearing in mind
that:
■ A minimum clearance of 20 mm has to be kept between the bottom of the
cooking hob and the top of an appliance or a shelf. To ensure this clearance
mount the spacers, supplied with the appliance, as shown in the figure below.
■ Overhead clearances - In no case shall the clearance between the highest
part of the hob and a range hood be less than 600 mm, or for an overhead
exhaust fan, 750 mm. Any other downward facing combustible surface less
than 600 mm above the highest part of the hob shall be protected for the full
width and depth of the cooking surface area in accordance with local regulations in force. However, in no case shall this clearance to any surface be less
than 450 mm.
■ Side clearances - Where the dimension from the periphery of the nearest
burner to any vertical combustible surface is less than 200 mm, the surface shall
be protected in accordance with with local regulations in force to a height of
not less than 150 mm above the hob for the full dimension (width or depth) of
the cooking surface area.
Where the dimensions from the periphery of the nearest burner to any vertical
combustible surface is less than 200mm, the horizontal surface shall be greater
than 10 mm below the surface of the hob, or the horizontal surface requirement above.
■ Protection of combustible surfaces - Local regulations in force specify that
where required protection shall ensure that the surface temperature of the combustible surface does not exceed 65 °C above ambient. The fixing of 5 mm
thick ceramic tiles to the surface or attaching fire resistant material to the surface
and covering with sheet metal with minimum thickness of 0.4mm should be
satisfactory.
Figure 3
20 mm
8
Figure 4a Fig. 4b Figure 4c Fig. 4d
Figure 4e
APPLYING THE SEALS
(Refer to Figures 4):
■ Turn the cooker top upside down.
■ Spread the longer seal “A” around the left, rear and right sides as shown in
figure 4a.
■ With a cutter or a scissors cut the excess seal “C” and retain it for next use
(figure 4b)
■ Spread the seal “B” around the left, front and right edges of the cooker top
as shown in figure 4c.
■ Spread the seal “C” along the rear edge of the cooker top as shown in
figure 4d. Making sure that the beginning and the end overlap at the seal
“B” (see figure 4e).
FRONT
seal A
seal C
seal A
seal C seal B
seal C
seal B
9
FASTENING THE INSTALLA-
20 mm min.
40 mm max.
B
seal A
F
20 mm min.
40 mm max.
B
seal C
seal A
R
TION BRACKETS
(Refer to Figures 5):
Each cooker top is provided with an
installation kit including brackets and
screws for fastening the top to fixture
panels from 2 to 4 cm thick.
■ Turn the cooker top upside down
and fasten the brackets “F and R”
to the appropriate socket holes,
without tightening the screws “B”
for the moment.
■ Make sure that the brackets are
fastened as shown in figure 5a,
5b and 5c.
Figure 5a
R
FASTENING THE COOKER
TOP (Refer to Figures 5):
■ Insert the cooker top into the
hole and position it correctly.
■ Adjust the position of the
brackets “F and R” and tighten
screws “B” to block the cooker
top firmly in position.
■ With a sharp cutter or trimmer
knife trim the excess sealing
material around the edge of the
Take care not to
cooker top.
damage the countertop.
R
Figure 5b
Rear side
F
FRONT
F
Figure 5c
Front side
10
GAS SUPPLY:
Figure 6b
Figure 6a
Gas connection for
UNIVERSAL LPG
Test point adaptor
Gasket
Brass conical adaptor
(Thread tight: use
suitable seal)
Gas inlet pipe
Test
point
Gas connection for
NATURAL GAS
Gas inlet pipe
Gasket
Brass conical adaptor
(Thread tight: use
suitable seal)
Gas regulator
Test
point
■ The connection must be executed by an authorised person according to the relevant
standards.
■ Before connecting the appliance to the gas main, mount the brass conical adaptor
onto the gas inlet pipe, upon which the gasket has been placed (figures 6a-6b).
Conical adaptor and gasket are supplied with the appliance (packed with conversion
kit for use with Natural gas or Universal LPG).
■ This appliance is suitable for use with Natural Gas or Universal LPG. (Check the “gas
type” sticker attached to the appliance).
■ For Natural Gas models the gas supply is connected to the pressure regulator which is
supplied with the appliance (fig. 6a). Model DEGH70W: adjust the regulator to obtain
a test point pressure of 1 kPa with the two semi-rapid (SR) burners operating at the maximum. Model DEGH70WF: adjust the regulator to obtain a test point pressure of 1 kPa
with the Triple-ring (TR) burner operating at the maximum.
■ For Universal LPG models the gas supply is connected to the test point adaptor
which is supplied with the appliance (fig. 6b) and ensure that the supply pressure is
regulated to 2.75 kPa.
■ Do NOT force the ”elbow“ rotation prior to loosening nut.
■ Do NOT over tighten the nut at the ”elbow“.
Loading...