Page 1
ELECTRIC SUPER PANEL HEATER
We were thinking of you
when we thought of it
Australia
P.O.Box 597
Riverwood NSW 2210
Customer Service
Ph: 1800 126659
Fax: 1800 706932
e-mail:custserv@parex.co.nz
Made in PRC
Proundly distributed by
Parex Industries Limited
25 CARBINE ROAD,
MT WELLINGTON
PO BOX 58056
GREENMOUNT
Auckland, New Zealand
Customer Service Ph: (09) 915 7273
Fax: (09) 915 7280
e-mail:custserv@parex.co.nz
Page 2
2
C
A
(X)
50 mm min
25
mm
min
25
mm
min
BB
F
F
E
F
F
Bracket
Bracket
Screw
Screw
Wall plug
50 mm min
D
Electric Super Panel Heater
Description of heater
The following terms are used throughout the instruction manual
Model
500 W
800 W
A
464
714
B
149
149
C
65
65
D
497
497
E
425
675
All measurements are in mm
Fig.1
Page 3
3
1
2
(Y)
Fig.2
Fig.3
HOW TO USE YOUR ELECTRIC SUPER PANEL HEATER
Thank you for choosing this Dè Longhi heater.
Please read this instruction booklet carefully before using
this heater. By doing so, you will obtain optimum results
with maximum safety.
General instructions
Remove the heater from the packaging. Check that neither the
heater nor the power cable has been damaged during transport.
Do not operate the heater if damaged.Your heater is suitable for
either freestanding or wall mounting usage. Do not assemble the
feet if wall mounting.
Free standing operation
To fit the feet to the appliance, proceed as follows:
Slide the foot’s tab on the slot provided on the back of the heater
then fix the foot with the relevant screw, as shown in fig.2.
Installation wall-mounting
The wall mounting kit should contain:
2 x Upper brackets (X)
2 x Lower brackets (Y)
4 x Screws (4,5 x 25)
4 x Wall plugs ( ø 6 x 30)
2 x Feet screws (3,5 x 9,5) (for freestanding operation)
1. Select position for siting the heater ensuring that:
a. It is not located directly below a power socket outlet.
b.The plug and power outlet can be easily reached after
installation.
c. No electric cables or other tubes could be damaged.
d.Keep away from curtains or inflammable materials.
Also note the minimum distances indicated in the
description:
2. Before drilling the wall, mark out a template following carefully
the dimensions as shown in fig.1.
3. For solid brick walls, use a 6mm masonry drill bit and drill
according to the marks F you have made and then insert the wall
plugs provided. (For plasterboard we suggest, locating the studding and using No. 6 woodscrews directly into the wood,or special plasterboard fixings. For other wall types please seek specialist advice).”
4. Mount the wall bracket “X” in the “F” holes using the screws provided.
5. Hang the heater on the brackets.
6. Position the lower brackets (Y) into the tabs located in the base
of the heater. See Fig 3. Move the bracket up until it is horizontal and then fix them with the screws provided.
Electric Super Panel Heater
Page 4
4
INSTRUCTIONS FOR USE
Switching on
Plug into the mains socket. Switch the appliance on using the
switch/switches following the procedures given:
-switch «Eco» = minimum power (indicator light on);
-switch «Med» = intermediate power (indicator light on);
- both switchess «Eco» «Med» = Max (indicator lights on)
To turn appliance off, switch off both switches or remove plug
from wall socket.
Maintenance
Before carrying out any maintenance, unplug the heater from the
mains and wait for it to cool.The heater requires no particular
maintenance. It is sufficient to remove the dust with a soft, dry
cloth. Never use abrasive powders or solvents. If necessary remove
concentrated areas of dirt with a vacuum cleaner.
Warnings
- Do not use the heater in a bathroom or in the vicinity of bathtubs, washbasins, showers or swimming pools.
-Never use the heater to dry laundry.
-Never place the power cable on top of the heater while it is hot.
- Only use the heater in an upright position.
- The appliance is not intended for use by young children or
infirm persons without supervision.
-Youg children should be supervised to ensure that they do not
play with the appliance.
- If the supply cord is damaged, it must be replace by the manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
- Do not locate the heater immediately below a socket- outlet.
-Do not block the hot-air outlet grilles or the intake grille.
- If the power cable is damaged, it must be replaced by the manufacturer or an authorised technical service centre.
We recommend that you not place the heater in a draught,
because strong draughts of air may adversely affect the equipment’s operational efficiency.
- IMPORTANT: Never for any reason cover the appliance dur-
ing operation as this could lead to dangerous overheating.
- The use of an extension lead is not recommended, as overheating of
the extension lead may occur during the operation of the heater.
- This appliance is filled with a precise quantity of oil and repairs
which require it to be opened must be carried out exclusively by
the manufacturer or an authorised service centre. In the case of oil
leaks, contact the manufacturer or the authorised service centre.
Electric Super Panel Heater
Page 5
- When scrapping the appliance,respect legislation on the disposal of oil.
- As with any electrical appliance, whilst the instructions aim to
cover as many eventualities as possible, caution and common
sense should be applied when operating your appliance, particularly in the vicinity of young children.
-Position the appliance so that the plug and the outlet can be
easily reached even after installation.
ELECTRICAL CONNECTION
- Before plugging the appliance into the mains, check that your
supply voltage is the same as that shown on the rating plate of
the appliance and that the electric installation is suitable to the
power shown on the rating plate.
Electric Super Panel Heater
5
Page 6
5712000200/12.02
Loading...