DeLonghi 24 E, 24 SS User Manual

• USERS OPERATING INSTRUCTIONS

• INSTALLATION ADVICE

IMPORTANT - PLEASE READ AND FOLLOW

✓ Before beginning, please read these instructions completely and carefully.
✓ Do not remove permanently affixed labels, warnings, or plates from the product. This

may void the warranty.

✓ Please observe all local and national codes and ordinances.
✓ Please ensure that this product is properly grounded.
✓ The installer should leave these instructions with the consumer who should retain

for local inspector's use and for future reference.

Electrical installation must be in accordance with the National Electrical Code,
ANIS/NFPA70 - latest edition and/or local codes.
IN CANADA: Electrical installation must be in accordance with the current CSA C22.1
Canadian Electrical Codes Part 1 and/or local codes.

Model: DEBIE 24 SS

DEBIE 24 E

SELF-CLEANING BUILT-IN ELECTRIC OVEN

for residential use only

2

Dear Customer,

Thank you for having purchased and given your preference to our

product.

The safety precautions and recommendations reported below are for
your own safety and that of others. They will also provide a means by
which to make full use of the features offered by your appliance.

Please preserve this booklet carefully. It may be useful in future, either
to yourself or to others in the event that doubts should arise relating to
its operation.

This appliance must be used only for the task it has explicitly been
designed for, that is for cooking food. Any other form of usage is to be
considered as inappropriate and therefore dangerous.

The manufacturer declines all responsibility in the event of damage
caused by improper, incorrect or illogical use of the appliance.

This appliance is designed and manufactured solely for the cooking of domestic (household)
food and in not suitable for any none domestic application and therefore should not be used
in a commercial environmement.

The appliance warranty will be void if the appliance is used within a none domestic
environmement i.e. a semi commercial, commercial or communal environment.

3

USER INSTRUCTIONS

USING THE OVEN FOR THE FIRST TIME

You are advised to carry out the following operations:

✓ Assemble the interior of the oven as described under the heading “Cleaning and

maintenance”

✓ Switch the empty oven ON at maximum temperature for about two hours to

eliminate traces of grease and smell from the components.

✓ Let the oven cool down, switch off the electrical supply, then clean the inside of the

oven with a cloth soaked in water and neutral detergent and dry thoroughly.

IMPORTANT PRECAUTIONS AND RECOMMENDATIONS

✓ After having unpacked the appliance, check to ensure that it is not damaged.

If you have any doubts, do not use it and consult your supplier or a
professionally qualified technician.

✓ Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps,

etc.) should not be left around within easy reach of children, as these may
cause serious injuries.

✓ The packaging material is recyclable and is marked with the recycling symbol

.

✓ Do not attempt to modify the technical characteristics of the appliance as

this may become dangerous to use.

✓ The manufacturer cannot be considered responsible for damage caused by

unreasonable, incorrect or rash use of the appliance.

✓ If you should decide not to use this appliance any longer (or decide to

substitute an older model), before disposing of it, it is recommended that it
be made inoperative in an appropriate manner in accordance to health and
environmental protection regulations, ensuring in particular that all potentially
hazardous parts be made harmless, especially in relation to children who
could play with old appliances.

✓ The appliance should be installed and all the electrical connections made by

a qualified technician in compliance with local regulations in force and
following the manufacturer's instructions

IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
FOR USE OF ELECTRICAL APPLIANCES

Use of any electrical appliance implies the necessity to follow a series of
fundamental rules. In particular:

✓ Never touch the appliance with wet hands or feet;
✓ Do not operate the appliance barefooted;
✓ Do not allow children or disabled people to use the appliance without your

supervision.

The manufacturer cannot be held responsible for any damages caused by
improper, incorrect or unreasonable use of the appliance.

4

control panel



Fig. 1.1

Oven controls:

1. Function selector knob

2. Electronic programmer

3. Temperature knob (potentiometer)

4. Door locked pilot light

5. Oven heating pilot light

6. Oven on pilot light

1 32

6

4 5

WARNING - VERY IMPORTANT NOTE:
The temperature knob (potentiometer) turns to right and left only to symbols + and -.
Forcing the turning could damage the temperature knob.

A
U
T
O

5

how to use the self cleaning oven



USING THE OVEN FOR THE FIRST TIME

- Put the shelf and the tray in the oven.

- Switch the oven on when it is empty (on any cooking function – NOT SELF CLEANING) at
maximum power for about 2 hours to remove traces of grease and smells from the com­ponents.

- When the oven has cooled down and the appliance, unplugged clean the inside of the oven
with a cloth soaked in water and neutral detergent and dry it completely.

WARNING:
The door is hot, use the handle.

NOTES ON OVEN WORKING

A cooling fan starts automatically when selecting a cooking or self cleaning mode.
It stops when turning the selector knob to OFF or light or defrosting position and
th inside oven cavity temperature drops below 100 °C (212 °F).
The purpose of this fan is to reduce the temperature inside/outside the appliance.

Note: The first time the oven is used or after a black-out the program must be started

by pressing keys 2 and 3 simultaneously. See the section on the use of the electronic
programmer.

OPERATING PRINCIPLES

Heating and cooking in the multifunction self cleaning oven takes place as follows:

• by normal convection

The heat is produced by the upper and lower heating elements.

• by forced convection

The heat produced by the circular element is distributed throughout the oven by the
fan.

• by radiation

The heat is radiated by the infra red broil element.

• by radiation and fan

The radiated heat from the infra red broil element is distributed throughout the oven
by the fan.

• by double radiation and fan

The fan distributes the heat radiated by the broil heating element and the upper heat­ing element in the oven.

• by ventilation

The food is defrosted by using the fan only function without heat.

• by self cleaning

The heat produced by the heating elements cleans the internal oven cavity removing
all residue of grease.

THIS IS NOT A COOKING FUNCTION

GENERAL FEATURES

The oven has special operating features.
Five different functions can be used to satisfy all cooking needs; it also has a self clean-

ing function which can clean the oven cavity at high temperature, a defrost function and
an oven light function.

These functions are managed by an electronic programmer which keeps the tempera­ture set constant by means of a probe inside the oven cavity.

The oven has the following heating elements:

- Lower heating element (double) 500 +1300 W

- Upper heating element 1000 W

- Grill heating element 2000 W

- Circular heating element 2200 W

Attention: the oven door becomes
very hot during operation.
Keep children away.

VERY IMPORTANT
The oven shall be used always
with the door closed.

WHEN THE SELF CLEANING
MODE HAS BEEN COMPLETED:

• do not start immediately a new
self cleaning cycle: LET THE
OVEN TO COOL DOWN.

2

I

I

I

I

I

I

IIII

3

IIIIII

I

I

I

I

I

I

IIIIIIIIII

6



OVEN LIGHT (this is not a cooking function)

Turning the knob to this position, only the oven lamp lights up.
The lamp is always on in all the cooking functions (not for the self cleaning).

SELECTING THE FUNCTIONS (fig. 2.1)

The cooking function is selected by turning the function selector knob and matching
the mark with the symbol printed on the print (or the symbol with the mark printed on
the print).

Fig. 2.1

If the door stays open “door” appears on the programmer dis­play and after five minutes an audible warning sounds for 30
seconds and “

door” flashes.

To silence the audible warning press any programmer pushbutton.

NOTE: The heating elements work even with the door open and this signal just
indicates that energy is being wasted and the control panel/knobs are excessive­ly heated.

DEFROSTING FROZEN FOODS (this is not a cooking function)

Only the fan and the oven lamp switch on. Defrosting takes place
by fan, without heating. The electronic program shows

dEF

Recommended for:

To rapidly defrost frozen foods; 2.2 lbs (1 kg) requires about one hour.
The defrosting times vary according to the quantity and type of foods to be defrosted.

CONVECTION COOKING WITH VENTILATION

The circular element and the fan switch on. The heat from the back is diffused by fan
convection. The temperature can be set between 120 °F (50 °C) and 480 °F (250 °C).
On selecting this function the electronic program starts cooking with a pre-heating tem­perature set at 320 °F (180 °C). To vary the temperature see the “Setting the cooking” sec­tion.

Recommended for:

For foods of large volume and quantity which require the same internal and external
degree of cooking; for ex: rolled roasts, turkey, legs, cakes, etc.

Important: In all cooking functions the oven must always be used with
the DOOR CLOSED.

IIIIII

IIII

I

I

I

I

I

I

I

I

I

I

I

I

IIIIIIIIII

7



TRADITIONAL CONVECTION COOKING

The upper and lower heating elements switch on.
The heat is diffused by natural convection and the temperature must be set between
120 °F (50 °C) and 480 °F (250 °C). On selecting this function the electronic program­mer starts cooking with a pre-heating temperature set at 350 °F (200 °C). To vary the
temperature see the “Setting the cooking” section.

Recommended for:

For foods which require the same cooking temperature both internally and externally, i.
e. roasts, spare ribs, etc.

VENTILATED COOKING WITH DOUBLE BROIL

The infrared element, the upper heating element and the fan switch on. The heat is
mainly diffused by radiation and the fan distributes it in the whole oven. The tempera­ture can be set between 120 °F (50 °C) and 480 °F (250 °C).
On selecting this function the electronic program starts cooking with a pre-heating tem­perature set at 480 °F (240 °C).
To vary the temperature see the “SETTING THE COOKING” section.
For correct use see the “VENTILATED BROILING” section.

Recommended for:

Meats which are to be cooked at a high temperature but which must remain tender.
Fish remains more tender; turn it once during cooking.

BROILING

The infrared heating element switches on.
The heat is diffused by radiation. The temperature can be set between 120 °F (50 °C)
and 480 °F (250 °C). On selecting this function the electronic program starts cooking with
a pre-heating temperature set at 480 °F (210 °C).
To vary the temperature see the “SETTING THE COOKING” section.
For correct use see the “BROILING” section.

Recommended for:

Intense broiling action for cooking with the broiler; browning, crisping, toasting, etc. For
correct use see the “BROILING” section.

VENTILATED BROILING

The infrared heating element and the fan switch on. The heat is mainly diffused by radi­ation and the fan distributes it in the whole oven.
The temperature can be set between 120 °F (50 °C) and 480 °F (250 °C). On selecting
this function the electronic program starts cooking with a pre-heating temperature set at
480 °F (220 °C). To vary the temperature see the “SETTING THE COOKING” section.

Recommended for:

For grill cooking when a fast outside browning is necessary to keep the juices in, i. e. veal
steak, steak, hamburger,

etc. For correct use see the “VENTILATED BROILING” section.

8



IMPORTANT NOTES:
This is not a cooking function but is only used to

clean the oven.

Before starting the self cleaning cycle:

-Take all the accessories out of the oven (broiling
pan and shelves).

- Clean any traces of liquid which have overflowed.

- Close the oven door and make sure that it is
closed properly.

If there are cracks or flaws on the oven door glass
(inside/outside) or if the gaskets are ruined or worn
or if the door does not close perfectly, unplug the
appliance and contact the Service Centre.

GENERAL INFORMATION

• In this function the residual cooking greases on the inside walls of the oven cavity are

pulverised by the high temperature. The fumes produced during this process are fil­tered by a special catalyst in the upper part of the appliance.

• Smells and fumes produced during self cleaning are not a cause of alarm. Adequate
ventilation should however be provided in the room where the range is installed, e.g.
by opening a window.

• Do not wait for the oven to be very greasy before performing this cleaning. It should
not be performed after every cooking, either, but only when the level of dirt justifies it
(on average 1 – 2 times a month depending on oven use).

• For safety reasons (high temperature of the oven cavity), when the self cleaning starts,
the oven door is automatically locked by an electronic device (after about 30 seconds
on the control panel the door locked pilot light lights up). The door can no longer be
opened and is only unlocked at the end of the cleaning cycle or, stopping the cycle,
when the oven cavity has cooled to a temperature lower than 570 °F (300 °C).

• When the self cleaning function starts an internal fan starts automatically to cool the
oven walls. It only stops at the end of the cycle, when the oven cavity temperature has
dropped below 212 °F (100 °C).

• The procedures for starting, stopping and completing the self cleaning cycle and deal­ing with any problems are described in the following section:

- “How to start the self cleaning cycle”

- “Problems on starting and during the self cleaning cycle”

- “How to stop the self cleaning cycle”

- “What to do when the self cleaning cycle has finished”

- “Abnormal situations and/or operating problems”

CAUTION: During the self clean­ing cycle the accessible parts
may become hot. Keep children
away.

SELF CLEANING FUNCTION (this is not a cooking function)

IMPORTANT:
The health of some birds is
extremely sensitive to the fumes
given off during the self-cleaning
cycle.
Exposure to the fumes may result
in death to certain birds.
Always move birds to another
closed and well ventilated room.

WHEN THE SELF CLEANING
MODE HAS BEEN COMPLETED:

• do not start immediately a new
self cleaning cycle on the same
oven: LET THE RANGE TO COOL
DOWN.

9



SELECTING °F/°C ON THE DISPLAY

1. Turn the oven selector knob to a cooking function (i.e. ).

2. Press key 5 on the programmer to reduce the temperature until you reach the min-

imum value (120 °F/50 °C).

3. With °F/°C flashing on the display press key 5 again (if °F/°C is not flashing press

key 4 before pressing key 5) until OFF appears on the display.

4. Keep key 4 pressed for about 3/5 seconds until the display changes from °C to °F

or vice versa. During selection °C or °F is flashing.

5. When OFF appears again on the display turn the selector knob to OFF position; the

selection to °C or °F has been completed.

➀

➂

➃

➄

➁

I

I

I

I

I

I

I

I

I

I

I

I

I

5

5

4

10



The temperature set is shown on the electronic program display and can be var­ied, with 5 °F (5 °C) intervals, by means of the temperature knob (potentiome­ter) or the program keys.
During cooking the oven temperature (°F or °C) is measured by a sensor inside
the cavity and is shown on the program display until set temperature is reached.
If set temperature is less than inside oven temperature, the display shows the
set temperature.

1.

SELECTING THE COOKING FUNCTION
Turn the selector knob to the cooking function required

The pre-set temperature appears on the program display. °

F or °C flashes

on the display for 3 seconds. The heating elements start cooking immedi­ately.

2.

SETTING THE COOKING TEMPERATURE
Turn the potentiometer knob clockwise to increase the temperature or
anticlockwise to reduce it.

The maximum temperature which can be set is 480 °F (250 °C) while the
minimum temperature is 120 °F (50 °C).

or use the program keys in the following way:

The temperature can be changed when °

F or °C is flashing on the display.

2a. If °

F or °C is not flashing press key 4 of the program.

2b Press key 6 to increase the temperature or key 5 to reduce it.

The maximum temperature which can be set is 480 °F (250 °C) while the
minimum temperature is 120 °F (50 °C).

Note: When °

F or °C becomes steady the value shown on the display indicates

the oven cavity temperature until set temperature is reached. If set temperature
is less than inside oven temperature, the display shows the set temperature.

Caution: If a temperature below the minimum value (120 °F or 50 °C) is set the
system switches off automatically and OFF appears.
In this case repeat the procedure from point 2.

3.

SWITCHING OFF

Turn the selector knob to position OFF (oven OFF). The program display
shows the time.

SETTING THE COOKING (ONLY FOR THE COOKING FUNCTIONS)

➀

➁

or

➁

➂

Function

selector knob

Programmer

Temperature
knob

NOTE: The temperature knob (potentiometer) turns to right and left only to
symbols + and -. Forcing the turning could damage the temperature knob.

2a 2b

A
U
T
O

I

I

I

I

I

I

I

I

I

I

I

I

I

56

4

11



I

I

I

I

I

I

I

I

II

I

I

I

I

I

I

➂

➃

➄

HOW TO START THE SELF CLEANING CYCLE

Important: the self cleaning cycle must only be performed with the oven empty; so,
before starting the cycle take all the accessories (shelves, broiling pan, ...) out of
the oven cavity and dry any traces of overflowed liquid.
Do not use any degreasing products (e.g. degreasing sprays, detergents, etc.).

1. Close the oven door (if it is open or not closed properly the self cleaning cycle will

not start).

2. Turn the oven selector knob to the self cleaning position (CLEAN); P0•00

appears on the electronic program display with the letter P flashing.

3. Press push button 3 on the program to start the cycle.

This combined confirmation operation offers greater safety when there are children;
in fact turning the knob to the self cleaning function has no effect if key 3 of the pro­gram is not then pressed.

•

P1•30 (self cleaning time, 1 hour and 30 minutes) appears and the door is locked

after about 30 seconds;

• On the control panel the door locked pilot light lights up to indicate that the door is
locked.

4. To increase the self cleaning cycle time (max 5 hours) press key 2 of the program

then key 6. To go backwards to the minimum of 1 hour and 30 minutes press key 2
then key 5.

• During the setting

AUTO flashes and P disappears.

5. The self cleaning cycle starts immediately and is completed in the programmed

time.

• Throughout the self cleaning cycle the program displays the time (hours and min­utes) remaining until the cycle is finished.

➁

VERY IMPORTANT:
The self cleaning cycle only starts with the oven door closed. If the door is open

or not closed properly the oven CANNOT perform the self cleaning cycle; elec­tronic safety devices prevent the self cleaning cycle from starting.

3

I

I

I

I

I

I

I

I

I

I

I

2

56

12



PROBLEMS ON STARTING AND DURING THE SELF CLEANING CYCLE

1. Steady door

The function selector has been turned to the self cleaning position with the oven
door open or not perfectly closed. Or the door has been opened before the cycle
has been started with confirmation from key 3

What to do:

Close the door and repeat previous cycle.

. If after 5 minutes the door has not been closed door flashes and an audible sig-

nal sounds for 30”.

What to do:

Close the door, press any program key to silence the audible signal and repeat the oper­ations to start the cycle.

2. door with AUTO flashing

The oven door has been opened after the self cleaning cycle has started (before
locking the door). The self cleaning cycle is zeroed.

What to do:

1. Close the door. P0•00 appears on the electronic program display with the letter P
and AUTO flashing.

2. Turn the function selector to

OFF and repeat the operations to start the cycle.

. If after 5 minutes the door has not been closed door flashes and an audible sig-

nal sounds for 30”.

What to do:

Close the door, press any program key to silence the audible signal and repeat the oper­ations to start the cycle.

3. F0.00 with AUTO flashing

The self cleaning cycle has been stopped and then started again when it was quite
a way through. The message is displayed after about 10 minutes and the self clean­ing cycle is zeroed.

What to do:

1. Put the switch to

OFF.

2. Wait for at least 15 minutes.

3. Repeat the operations to start the self cleaning cycle.

4. If after several attempts the message continues contact the Service Centre.

Caution: It is advisable not to stop the self cleaning cycle and then start it again
when it is quite a way through.

I

I

I

I

IIII

I

I

IIIIII

I

I

I

I

I

I

IIIIIIIIII

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

IIIIIIIIII

I

IIIIII

IIII

I

I

I

I

I

I

I

I

I

I

I

13

➀

➁

1a

1b

2a

2b

2d

I

I

I

I

I

I

I

I

I

I

I

➀

➂

HOW TO STOP THE SELF CLEANING CYCLE

1. Turn the function selector to OFF (oven OFF)

- If the oven cavity temperature is higher than 570 °F (300 °C)

1a. The time of day appears steadily on the program display.
1b. When the oven cavity temperature drops below 570 °F (300 °C):

-

OFF appears on the program display again

- the door locked pilot light goes out

- the door unlocks and can be opened

- If the oven cavity temperature is lower than 570 °F

1c. The time appears on the program display
1d. After a technical time:

- the door locked pilot light goes out

- the door unlocks and can be opened

IMPORTANT: Wait for the oven to cool down completely before starting a cooking
function.

ACCIDENTAL INTERRUPTION OF THE SELF CLEANING CYCLE

2. The function selector has been turned to any cooking function

- If the oven cavity temperature is higher than 570 °F (300 °C)

2a. The time of day appears steadily on the program display.
2b. When the oven cavity temperature drops below 570 °F (300 °C):

-

OFF appears on the program display

- when door locked pilot light goes out (after some minutes) the door unlocks and
can be opened

2c. To reset normal conditions turn the function selector to

OFF (oven OFF). The time

appears on the program display.

- If the oven cavity temperature is lower than 570 °F (300 °C)

2d. Pre-set temperature of the selected function appears on the program display.
2e. After a technical time:

- the door locked pilot light goes out

- the door unlocks and can be opened

2f. To reset normal conditions turn the function selector to OFF (oven OFF). The time

appears on the program display.

IMPORTANT: Wait for the oven to cool down completely before starting a cooking
function.

WHAT TO DO WHEN THE SELF CLEANING CYCLE HAS FINISHED

1. P0.00 with AUTO flashing.

Wait for the oven to cool down and the door to unlock.

The self cleaning cycle has finished.

P0.00 will remain until the door is unlocked.

The door remains locked until the cavity temperature has dropped below 570 °F
(300°C).

2. The door locked light goes out (when the temperature has dropped below 570

°F - 300 °C).
AUTO and the letter

P flash.

The door is unlocked and can be opened.

3. Turn the function selector knob to OFF (oven OFF).

The time appears on the programmer display.

4.

Wait for the oven to cool down completely.

5. Remove the pulverised dirt.

Open the oven door and remove the residue of pulverised dirt inside the oven with
a damp cloth.

IMPORTANT: Before switching the oven on again in any function wait for the
appliance to cool down completely.



➁

14



ABNORMAL SITUATIONS AND/OR OPERATION PROBLEMS

during cooking or the self cleaning cycle.

1. 30 F0 or 30 F1 appear during the cooking or self cleaning cycle

Oven temperature sensor broken or not working properly. The cooling fan stays on
and if the self cleaning cycle is in progress the door remains locked.

What to do:

1. Turn the oven function selector to

OFF (oven OFF). A 30 minute countdown will

start. If the selector is turned and then returned to

OFF the count will start again

from 30.

2. Wait for the countdown to finish.
The fan switches off and the door, if locked, unlocks.

3. Disconnect the appliance from the main electrical supply and contact the Service
Centre because the oven can no longer be used.

Caution: If the function selector is not turned to

OFF (oven OFF), the cooling fan will

continue to work and the oven door, if locked, remains locked.

2. F0.00 appears during the self cleaning cycle

This indicates a temperature sensor measurement error during the self cleaning
cycle. This may be due to the self cleaning cycle being stopped and started again
when it was quite a way through.

What to do:

1. Turn the oven selector knob to

OFF (oven OFF).

2. Wait for at least 15 minutes before repeating the operations to start the self clean­ing cycle.

3. If the message is still given after several attempts call the Service Centre.

3. Display OFF - Oven not working properly.

What to do:

1. Turn the function selector to

OFF (oven OFF)

2. Wait for the oven to cool down completely so that the door opens

3. Switch the appliance off for a few seconds.

If after this procedure the display is still off:

4. Disconnect the appliance from the main electrical supply .

5. Call the Service Centre. The appliance must not be used.

I

I

I

I

I

I

I

I

I

I

I

15

COOKING DIFFERENT DISHES AT THE SAME TIME

The MULTIFUNCTION oven at positions of the function selector can cook
various different foods at the same time. Fish, cakes and meat can be cooked together
without the smells and flavours mixing.

The only precautions required are the following:
– The cooking temperatures must be as close as possible with a maximum difference of

70-80 °F (20-25 °C) between the different foods.

–Different dishes must be placed in the oven at different times according to the cook-

ing time required for each one. This type of cooking obviously provides a considerable
saving on time and energy.

COOKING ADVICE

STERILIZATION

Sterilization of foods to be conserved, in full and hermetically sealed jars, is done in the
following way:

a. Turn the switch to position .
b. Set the thermostat knob to position 350 °F (175 °C) and preheat the oven.

c. Fill the grill pan with hot water.
d. Set the jars into the grill pan making sure they do not touch each other and the door

and set the thermostat knob to position 260 °F (130 °C).

When sterilization has begun, that is, when the contents of the jars start to bubble, turn
off the oven and let cool.

ROASTING

To obtain classical roasting, it is necessary to remember:
– the pre-set temperature should be maintained

– that the cooking time depends on the quantity and the type of foods.

VENTILATED BROILING AND “AU GRATIN”

Broiling may be done by selecting or with the function selec­tor knob, because the hot air completely envelops the food that is to be cooked.
Set the temperature if a temperature different from the pre-set one is required.
Introduce the food to be cooked, positioning the grill pan as close to the infra-red ele­ment as possible.

Close the door and let the oven operate until broiling is done.
Adding a few dabs of butter before the end of the cooking time gives the golden “au

gratin” effect.

Broiling with the oven door closed.
Important: Use always suitable protective gloves when inserting/removing the

broiling pan from the oven (see next page).

It is advisable to handle
the oven accessories
using oven gloves.

WARNING

VERY IMPORTANT

WARNING!!



16



Fig. 2.2

WRONG

CORRECT

Fig. 2.3

Fig. 2.4

Fig. 2.5

BROILING

Very important: the broil element must always be used with the oven door
closed.

– Position the shelf on the first or second level from the top (fig. 2.2).

–Turn on the broil element, as explained in the preceding paragraphs and let the oven

preheat for about 5 minutes with the door closed.

– Place the food to be cooked above the broiler tray.

– Introduce the broiler tray (fig. 2.3) in the oven. The broiler tray should be placed

above the shelf and it should be centered with the broil element (fig. 2.2).

Do not broil without using the broiling pan

.

Important: Use always suitable protective gloves when inserting/removing the
broiling pan, shelves, pans on other cooking utensils from the oven.

1° STEP
2° STEP
3° STEP

4° STEP

17

Fig. 3.1

how to use the electronic program



Description of the light symbols:

AUTO

Indicates that a program has been set

Indicates that the heating elements are working

Indicates that the timer is working

P Indicates PM time

After the appliance has been connected to the main electrical supply or after there has
been a black-out the program must be activated so that it can work.

12:00 flashes on the display.

1. Press keys 2 and 3 at the same time.

The program starts to work.

ON SWITCHING ON FOR THE FIRST TIME OR AFTER A BLACK-OUT

The program has an electronic clock (12 hours) with luminous figures which indicate hours
and minutes.

Note: Setting the clock will zero any program in progress or set.

1. Press push buttons 2 and 3 at the same time.

2. Press push buttons 5 or 6 until the exact time is set. During this phase the dot between

hours and minutes will flash on the display. If the plus or minus keys are kept pressed
for a few seconds, the figures will scroll more quickly.

P on the display indicates PM time.

SETTING THE TIME

AUDIBLE SIGNAL

The intermittent audible signal, duration 30 seconds, sounds when the timer or semi­automatic or automatic cooking have reached the end of the time set. It also sounds to
signal that the door is open (see oven use section).

To silence the audible signal press any of the program keys.

The electronic programmer is a device which groups together the following functions:
– 12 hours clock with illuminated display (P on the display for PM time indication).

–Timer (up to 23 hours and 59 minutes).
– Program for semi-automatic oven cooking.
– Program for automatic oven cooking.
– Management of the cooking functions. The programmer can manage setting the tem-

perature in the various cooking functions.

– Management of the self cleaning function.

Description of the pushbuttons:

Timer (1)
Cooking time or self cleaning time (2)
End of cooking time or allowance to start self cleaning cycle (3)
Setting oven temperature (4)
Countdown of the figures of all the functions or of the temperature to be set (5)
Advance of the figures of all the functions or of the temperature to be set (6).

A
U

T

O

12

3

IIIIII

IIII

I

I

I

I

I

I

3

2

I

I

I

I

I

I

I

I

I

I

I

3

2

4

I

I

I

I

I

I

IIIIIIIIII

56

56

18



The timer function is only used to count the time and does not influence oven operation
or any program which are in progress or set.

1. Press push button 1. The bell symbol will start to flash.

2. Press keys 5 or 6 to set the time required.

3. The countdown starts immediately. The bell symbol stops flashing and the time

appears again.

4. To see the countdown press push button 1. The time will be indicated in hours and

minutes; the seconds are only indicated for the last minute.

5. At the end of the countdown an audible signal sounds and the bell symbol on the

display flashes.
Press any push button to stop the audible signal.

IMPORTANT WARNING: This function is only an electronic alarm and does not
switch OFF the oven. Remember to turn OFF manually the selector knob at the
end of the countdown.

TIMER

Setting

1. Set the cooking function by turning the oven selector to the function required.

2. The cooking temperature appears on the display. To change it proceed as

described in the “Setting the cooking” section.

3. Press push button 2. AUTO starts to flash and 0.00 appears.

4. Press push buttons 5 or 6 to set the cooking time (cooking time in hours and min-

utes: set it to ten minutes less than the time required because the stored heat will
complete the cooking).

5. On the display AUTO becomes steady and the cooking program starts.

During cooking

6. During the cooking cycle, the display shows the oven temperature measured by the

probe or pre-set temperature.
Press key 2 to display the time remaining until the end of cooking.
The cooking time and temperature can be varied at any time, as described above.

At the end of cooking

7. End appears on the display, AUTO flashes and the audible signal sounds.

The cooking cycle has finished and the oven is OFF.

8. Press any program push button to stop the audible signal.

9. OFF appears (oven OFF).

10. Turn the function selector to OFF (oven OFF).

11. The program display shows the time.

SEMI-AUTOMATIC COOKING

Start immediate cooking and switch the oven off automatically
after the programmed cooking time.

Note: At the end of the program always turn the function selector knob
to OFF (oven OFF).

I

I

I

I

I

I

I

I

I

I

I

1

56

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

2

56

I

I

I

I

I

I

I

I

I

I

I

19

Setting

1. Set the cooking function by turning the oven selector to the function required.

2. The cooking temperature appears on the display. To change it proceed as described

in the Setting the cooking section.

3. Press push button 2. AUTO starts to flash and 0.00 appears.

4. Press push buttons 5 or 6 to set the cooking time (cooking time in hours and min-

utes: set it to ten minutes less than the time required because the stored heat will
complete the cooking).

5. On the display AUTO becomes steady and the cooking program starts.

6. Press push button 3 (AUTO starts to flash).

7. Press push buttons 5 or 6 to set the time when the cooking should finish.

The values set must be correct; e.g. if it is 08:00 a cooking time of 3 hours, ending
at 10:00, cannot be set. In this case the programmer automatically sets the end of
cooking time for 11:00.

8. On the display AUTO becomes steady and the time appears again. The cooking

symbol goes out.

Starting cooking

9. The pan symbol lights up. The oven switches on and the cooking cycle set starts.

AUTOMATIC COOKING

Start cooking at the programmed time and switch the oven off
automatically after the programmed cooking time.

During cooking

10. During the cooking cycle, the display shows the oven temperature measured by

the probe or pre-set temperature.

Press key 2 to display the length of cooking set.

Press key 3 to display when the cooking will finish.

The cooking time, end of cooking time and cooking temperature can be varied at
any time, as described above.

At the end of cooking

11. End appears on the display, AUTO flashes and the audible signal sounds.

The cooking cycle has finished and the oven is OFF.

13. Press any push button to stop the audible signal.

14. OFF appears (oven OFF).

15. Turn the function selector to OFF (oven OFF).

16. The program display shows the time.

Note: At the end of the program always turn the function selector knob
to OFF (oven OFF).

IMPORTANT: During AUTOMATIC COOKING PROGRAM the oven light is
always on, also before starting (heating elements on or cycling) of the
programmed cooking.



I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

I

2

I

I

I

I

I

I

I

I

I

I

I

56

3

56

I

I

I

I

I

I

I

I

I

I

I

20

Time needed to cook
the food (2 hours)

Time when the food
to be cooked must
be ready

Time when cooking
the food is pro­grammed (08:00)

Programmable

functions

Fig. 3.2

EXAMPLES OF PROGRAMMING AUTOMATIC COOKING

➂

➁

➀

➀

➁

➂



To cancel any program just turn the function selector to OFF (oven OFF).

Note: if during a set program the function selector is turned to

OFF (oven OFF), SELF

CLEANING or oven lighting, the program is cancelled.

CANCELLING A SET PROGRAM

12

11

10

9

8

7

1

2

3

4

5

6

P

A
U

T

O

P

A
U
T

O

256

P

A
U
T

O

536

21

cleaning and maintenance



GENERAL RECOMENDATION

✓ Important: Before any operation of cleaning and maintenance disconnect the

appliance from the electrical supply.

✓ It is advisable to clean when the appliance when it is cold and especially for clean-

ing the enamelled parts.

✓ Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the sur-

faces.

✓ Avoid using cleaning products with a chlorine or acidic base.

The oven must always be cleaned after every use, using suitable products and keep­ing in mind that its operation for 30 minutes on the highest temperature eliminates
most grime reducing it to ashes.

ENAMELLED PARTS

✓ All enamelled parts must be cleaned with a sponge and soapy water only or other

non-abrasive products.
Dry preferably with a chamois leather.

PAINTED PARTS AND SILK-SCREEN PRINTED SURFACES

✓ Clean using an appropriate product. Always dry thoroughly.

IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abra­sion. You are advised to use a soft cloth and neutral soap.

STAINLESS STEEL ELEMENTS

✓ Stainless steel parts must be rinsed with water and dried with a soft and clean

cloth or with a chamois leather.

✓ For difficult dirt, use a specific non-abrasive product available commercially or a

little hot vinegar.

INSIDE OF OVEN

✓ This must be cleaned regularly.
✓ With the oven warm, wipe the inside walls with a cloth soaked in very hot soapy

water or another suitable product.

Before any operation of maintenance
disconnect the appliance from the
electrical main supply.

WARNING

VERY IMPORTANT

22

REMOVING THE OVEN DOOR

The oven door can easily be removed as follows:

– Open the door to the full extent (fig. 4.3a).

– Open the lever “A” completely on the left and right hinges (fig. 4.3b).

– Hold the door as shown in fig. 4.3.

– Gently close the door (fig. 4.3c) until left and right hinge levers “A” are hooked to part

“B” of the door (fig. 4.3b)

– Withdraw the hinge hooks from their location following arrow “C” (fig. 4.3d).

– Rest the door on a soft surface.

– To replace the door, repeat the above steps in reverse order.

Fig. 4.3

Fig. 4.3a

Fig. 4.3b

Fig. 4.3d

Fig. 4.3c



Fig. 4.1

OVEN SHELF INSTALLATION AND REMOVAL

The oven shelves are provided with a security block to prevent accidental extraction.
They must be inserted operating as per figure 4.1.

To pull them out remove shelf in the inverse order.

Pay attention how to insert the shelves correctly (see figure 4.1).

Fig. 4.2

REPLACING THE OVEN LIGHT (fig. 4.2)

Before any maintenance is started involving electrical parts of the appliance, it must be
disconnected from the power supply.

– Let the oven cavity and the heating elements cool down;

– Switch off the electrical supply;

–Remove the protective cover (fig. 4.2);

– Unscrew and replace the bulb with a new one suitable for high temperatures (300°C)

having the following specifications: 120V, 60 Hz, 25W, E14

– Refit the protective cover

NOTE: Oven bulb replacement is not covered by your warranty.

Safety catch

B

A

A

B

C

23

WARNING!

THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER.
Installation must conform with local codes.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a

qualified installer or service agent. IMPORTANT: The use of suitable protective clothing/gloves is recommended when
handling, installing of this appliance.

WARNING: When correctly installed, your product meets all safety requirements laid down for this type of product
category.

However special care should be taken around the rear or the underneath of the appliance as these areas are not
designed or intended to be touched and may contain sharp or rough edges, that may cause injury.

INSTALLATION INSTRUCTIONS

GENERAL INFORMATION

1. Installation must conform with local codes.

2. WARNING: This appliance shall not be used for space heating. This information is
based on safety considerations.

3. Keep appliance area clear and free from combustible materials, gasoline, and other
flammable vapors.

4. Disconnect the electrical supply to the appliance before servicing.

5. When removing appliance for cleaning and/or service;

A. Disconnect AC power supply.
B. Carefully lift appliance out of cabinet cutout.

CAUTION: Use care in handling.

6.

Electrical Requirement

Electrical installation should comply with national and local codes.

WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS

The appliance must be electrically grounded in accordance with local codes or,
in the absence of local codes, with the National Electrical Code, ANSI/NFPA No.

70-latest edition, in Canada Canadian Electrical Code.
Installation should be made by a Iicensed electrician.

For personal safety, this appliance must be properly grounded.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the
appliance. Replacement parts are available from factory authorized parts distributors.
Contact the nearest parts distributor in your area.

24

GENERAL INFORMATION

The oven can be fitted in standard units, minimum width and depth 23" 5/8 (600 mm).
Installation requires a compartment as illustrated in figures 5.1 and 5.2.
On the lover side, the oven must lay on supports withstanding the oven weight.
The oven should then be secured by 4 screws (not supplied) fitted into the holes pro­vided at the sides of the oven (Fig. 5.3). If you open the oven door, you will see some
screw holes. Remember the housing should not be free standing but be secured to the
wall and/or adjacent fittings.

A

B

E

D

L

C

I

F

F

H

G

A

B

D

E

C

Fig. 5.1

Fig. 5.2

installation to the cabinet



Ref. inches mm

A 24" 609.5

B 24" 608.7

C 21" 7/8 max 556 max

D 22" 3/64 max 560 max

E 15/16" 24

F 22" 3/64 560

G 23" 1/32 585

H 1" 31/32 50

I 23" 17/64 591

L 22" 7/16 min 570 min

NOTE

It is essential that when installing your oven, adequate
air circulation is available within the installation.
Inadequate air circulation may greatly impair the per­formance of your oven and may affect adjacent cabi­nets due to an increase in temperature.

Adjust the hinges of cabinet door adjacent to the oven
to allow a 5 - 7 mm gap between the furniture door
and the oven frame.

Fig. 5.3

25

Fig. 5.4

1" 11/64 (30 mm)

23" 5/8 min (600 mm min)

1" 31/32 (50 mm)

1" 31/32 (50 mm) 21" 21/32 (550 mm)

Fig. 5.5

To ensure internal ventilation, aeration
channels must be provided as illustrated
in the figures 5.4 and 5.5.

The walls surrounding the oven must
be made of heat-resistant material.
Taking care NOT to lift the oven by the
door handle.

Fig. 5.6

IMPORTANT:
To avoid damage to the lower trim
please note the following instructions.

The lower trim is designed to allow for
good air circulation and the correct open­ing of the oven door.

To ensure the trim is not damaged due to
the appliance being placed on the floor,
the appliance should be suitably support­ed as in above illustrations.

After installation the appliance door
should be slowly opened to ensure no
damage has occurred.

No responsibility for lower trim dam­age will be accepted if these instruc­tions have not been followed.



AIR FLOW

OVEN DOOR

LOWER TRIM

26

This appliance must be connected to a grounded, metallic permanent wiring sys­tem or a ground connector should be connected to the ground terminal or wire
lead on the appliance.

This appliance is manufactured with a frame connected, green or bare ground wire.
Connect the appliance cable to the junction box through the CSA or UL-listed conduit
connector. Complete electrical connection according to local codes and ordinances.

CONNECT WITH COPPER WIRE ONLY

✓

The flexible (4’) armoured cable should be connected directly to the junction box.

✓

Do not cut the conduit.

✓

A CSA or UL-listed conduit connector must be provided at the junction box.

✓

Do not ground to a gas pipe.

✓

Do not have a fuse in the grounding or neutral circuit.

✓

Fuse both supply (phase) lines.

✓

A time delay fuse or circuit breaker is recommended.

✓

Connect directly to the fused disconnect (or circuit breaker box) through flexible,
armored or non-metallic shealted, copper cable (with grounding wire).

✓

If codes permit and a separate grounding wire is used, it is recommended that a
qualified electrician determine that the grounding path and wire gauge is in
accordance with local codes.

If the appliance is to be completely enclosed in a cabinet, feed the appliance
cable through the opening in the cabinet. Make the electrical connection follow­ing the appropriate steps for your installation.

1. Disconnect the power supply.

2. Remove the junction box cover.

3. Connect the appliance cable to the junction box through the CSA or UL-listed con­duit connector.

4. Connect the two black wires together with twist-on connectors.

5. Connect the two red wires together with twist-on connectors.

6. Connect electrical connection according to local codes and ordinances.

If local codes PERMIT connecting cabinet-grounding conductor to neutral white
wire in the junction box:

7. Crimp the green & yellow (or green) and white oven wires.

8. Connect the crimped green & yellow (or green) and white oven cable wires to the
neutral (white) wire in the junction box (Fig. 6.1).

9. Replace the junction box cover.

OR If local codes DO NOT PERMIT connecting cabinet-grounding conductor to
neutral white wire in junction box:

7. Connect white oven cable wire to neutral (white) wire in junction box (Fig. 6.2).

8. Connect the green & yellow (or green) grounding appliance cable wire to a ground­ed wire in the junction box.

9. Replace the junction box cover.

OR If connecting to a four-wire electrical system:

7. Connect white oven cable wire to neutral (white) wire in junction box (Fig. 6.2).

8. Connect the green & yellow (or green) appliance cable wire to the green & yellow (or
green) grounding wire in the junction box.

Do NOT connect the green & yellow (or green) appliance cable wire to neutral
(white) wire in junction box.

9. Replace the junction box cover.

electrical connection



Fig. 6.1

Fig. 6.2

WARNING

TO AVOID ELECTRICAL SHOCK
HAZARD, BEFORE INSTALLING THE
APPLIANCE, SWITCH POWER OFF AT
THE SERVICE PANEL AND LOCK THE
PANEL TO PREVENT THE POWER
FROM BEING SWITCHED ON
ACCIDENTALLY.

3-wire cable from

power supply

Junction box

Black wires

Red wires

White

wires

Green & yellow

wire

(or green wire)

4-wire cable from

Junction box

Red wires

Green & yellow

wires

(or green wires)

CSA or UL-listed

conduit connector

power supply

CSA or UL-listed

conduit connector

to appliance

White wires

Black wires

to appliance

27



ELECTRIC DIAGRAM

L1

ST4

ENCODER

°C+/- ST2

2

EL 1000

SIEBE

ST1 PROBE

COOLING
FAN

LOCK/UNLOCK

RELAY 3

Door opened/closed

OVEN DOOR LATCH

ETA

1

EL1000

3 ETA

42

ETA ETA

4

3

control device

EL 1000

ST3

AUX ETA

AUX ETA

5

Oven door

latch switch

33 ETA

34 ETA

DOOR SAFETY
PILOT LAMP

AIR
SWITCH

RELAY

E61

22a1

A

B

2

1

1

3

Safety
Thermostat

2

3a

5

A

5a

1a

THERMOSTAT
PILOT LAMP

RELAY 2

EL 1000

6

BOTTOM ELEMENT INT.

14

14a

Safety
Thermal overload

6

B

E61

RELAY SWITCH

9

B

THERMOSTAT

TOP ELEMENT

BOTTOM ELEMENT EXT.

15

13

13a

15a

LINE
PILOT LAMP

V

OVEN FAN

7

7a

7

8

8a

GRILL ELEMENT

CIRCULAR ELEMENT

11

12

12a

11a

4

7

RELAY 1

EL 1000

16a

16

OVEN LAMP

LF

9

9a

L2

N

EARTH

L1 - L2 = 240V
L1 - N = 120V
L2 - N = 120V

Cod. 1102812 - ß2

The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in
the present booklet.
The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture
or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and
safety characteristics of the appliances.