DeLonghi RADIANT, 182H, 541101 User Manual

RADIANT HEATER

SAFETY INSTRUCTIONS

(KEEP IN A SAFE PLACE)

SPARE COPIES OF THIS LEAFLET CAN BE OBTAINED FROM YOUR DEALER

U.K. AGENT:

De’Longhi Ltd.

15/16 Bridle Close - Stewarts Road
Finedon Industrial Estate
Wellingborough
Ph 0933 442040

X-Press 1-03-2002 11:54 Pagina 1

Heater safety instruction. (Keep in a safe place).

Spare copies of this leaflet can be obtained from your dealer.

1 Always use heater in accordance with

instructions supplied with each heater.
Keep Instructions in a safe place.

2 Do not place clothes or other materials

on the heater, as apart from the danger
of fire their presence could affect the effi­cient working of the appliance.

3 Do not position heater close to chairs and

fabrics.

4 Do not move heater from room to room

when it is lit.

5 Do not position heater alongside a wall or

near curtains, etc. Always face heater
towards centre of room.
Special care should be taken if the hea­ter is on a surface where it can move or
twist on its wheels or castors if knocked by
a child or dog, etc.

6 A LEAK WILL SMELL

If a leak is suspected, turn the gas off at
cylinder. Do not disconnect the regulator.
Extinguish all naked lights. Check all con­nections. Slowly turn the gas on and brush
the connections with soapy water or liquid
detergent - a gas leak will form bubbles. If
a leak is found turn the gas off and inform
your Dealer. DO NOT use the heater again
until it has been inspected by your Dealer.
If the cylinder valve appears to be
leaking when turned off, refit the Black
Branch Cap or Orange Valve Cap.

- This appliance MUST NOT be used in basements, high rise flats, bathrooms or bedrooms
and in rooms having volume less than 15m

3

(30m3in living rooms) for three burner models,

18m

3

(36m3in living rooms) for two burner models.

- Be sure installation is complying to local standard.

- Do not install the appliance in a room which might contain gas, oil or sulphur, or near sour­ces of heat.

- The appliance should not be used at altitudes exceeding 1500 m. as the analyzer may be
triggered off causing the appliance to switch off unexpectedly.

Ventilation

Use only in a well ventilated room (see page 4 of these instructions, where applicable).
Do not change cylinders in the presence of naked lights.

2

X-Press 1-03-2002 11:54 Pagina 2

SCREW ON REGULATOR

1. Connecting cylinder and turning the gas on

a Make sure that the black plastic cap is

screwed onto outlet of full cylinder.
Ensure valve operates freely by turning
anticlockwise to open and clockwise to
close. Firmly close valve by turning
handwheel clockwise. Remove black
plastic cap from valve outlet and store in
a safe place for future use.

b Make sure black neoprene washer is in

place on the regulator iniet. Regularly
examine, and if unduly compressed or
damaged, replace. Do not replace with
red branch cap washer.

c Support regulator, screw union nut onto

cylinder valve by turning nut anti-clockwise
(left-hand thread). Tighten just over hand
tight using Calor Spanner. After fitting the
regulator it may have assumed a position
out of the horizontal. This is not important.
Do not attempt to twist regulator.

d Place cylinder in cabinet so that the cylin-

der valve is facing into the compartment.
Open cylinder valve by turning
handwheel anticlockwise. Make sure that
all connections are gas tight, by brushing
with soapy water or liquid detergent (a
gas leak will form bubbles). Now refer to
the lighting instructions on the heater.

a Close cylinder valve by turning

handwheel clockwise. Check that the
heating elements and pilot are out.

b Open back the appliance, remove cylinder

and place close to heater (do not strain
hose). Support regulator, use a Calor
Spanner to disconnect regulator/ cylinder
valve union by turning nut clockwise (left-
hand thread). Care must be taken to ensu­re that the outlet connection on the regula­tor is not damaged or strained. Screw black
plastic cap onto valve outlet. Place empty
cylinder in a safe place.

2. Turning off and disconnecting the cylinder

Where the screw on regulator is used in conjuction with a switch-on adaptor refer to
instructions supplied with adaptor.

3

Gas Bottle

Gas Bottle with 15 kg of maximum capacity can be installed. Changing of gas bottle must not
be carried out in the presence of a naked flame. Use the gas bottle always in upright position.
If a screw on regulator is used ensure that the rgulator washer is present and in good condi­tion - replace if any doubt. To place the bottle in position, remove the rear panel which faces
the inside during transport, by unfastening the screws; than put the bottle in position and
replace the panel. Do not turn the bottle upside down to use completely its content.

X-Press 1-03-2002 11:54 Pagina 3