Dell Vostro 15-3559 User Manual

Dell Vostro 15–3559 Owner's Manual

Regulatory Model: P52F Regulatory Type: P52F003

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 08

Rev. A00

Contents

1 Working on Your Computer................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Recommended Tools............................................................................................................................6

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Removing and Installing Components............................................................. 8

Removing the Battery............................................................................................................................8

Installing the Battery..............................................................................................................................9

Removing the Optical-disk Drive..........................................................................................................9

Installing the Optical-disk Drive............................................................................................................9

Removing the Access Panel..................................................................................................................9

Installing the Access Panel..................................................................................................................10

Removing the Hard Drive....................................................................................................................10

Installing the Hard Drive......................................................................................................................12

Removing the Memory Module.......................................................................................................... 12

Installing the Memory Module............................................................................................................ 13

Removing the WLAN Card.................................................................................................................. 13

Installing the WLAN Card.................................................................................................................... 13

Removing the Coin-Cell Battery.........................................................................................................13

Installing the Coin-cell battery........................................................................................................... 14

Removing the Keyboard......................................................................................................................14

Installing the Keyboard........................................................................................................................15

Removing the Base Cover...................................................................................................................15

Installing the Base Cover.....................................................................................................................17

Removing the Input/Output (I/O) Board............................................................................................ 17

Installing the Input/Output (I/O) Board.............................................................................................. 18

Removing the Heatsink Assembly.......................................................................................................19

Installing the Heatsink Assembly........................................................................................................20

Removing the Speakers...................................................................................................................... 20

Installing the Speakers.........................................................................................................................21

Removing the System Board...............................................................................................................21

Installing the System Board................................................................................................................ 23

Removing the Power Connector....................................................................................................... 24

Installing the Power Connector......................................................................................................... 24

Removing the Display Assembly.........................................................................................................25

Installing the Display Assembly...........................................................................................................26

Removing the Display Bezel............................................................................................................... 27

Installing the Display Bezel................................................................................................................. 27

Removing the Camera........................................................................................................................28

Installing the Camera..........................................................................................................................28

Removing the Display Hinges.............................................................................................................29

Installing the Display Hinges...............................................................................................................29

Removing the Display Panel...............................................................................................................30

Installing the Display Panel..................................................................................................................31

3 System Setup....................................................................................................... 33

Boot Sequence....................................................................................................................................33

Navigation Keys................................................................................................................................... 33

System Setup Options.........................................................................................................................34

Updating the BIOS ..............................................................................................................................41

System and Setup Password...............................................................................................................42

Assigning a System Password and Setup Password.................................................................... 42

Deleting or Changing an Existing System and/or Setup Password.............................................43

4 Diagnostics..........................................................................................................44

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 44

5 Specifications...................................................................................................... 45

Specifications...................................................................................................................................... 45

6 Contacting Dell...................................................................................................50

Contacting Dell................................................................................................................................... 50

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the computer, replace all covers, panels, and screws before connecting to the power source.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

www.dell.com/regulatory_compliance

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

3. If the computer is connected to a docking device (docked), undock it.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• #0 Phillips screwdriver

• #1 Phillips screwdriver

• Small plastic scribe

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your computer.

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Slide the release latch outwards to unlock the battery.

3. Remove the battery from the computer.

Installing the Battery

1. Insert the battery into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your computer .

Removing the Optical-disk Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the optical-disk drive (ODD) to the computer [1]. b. Press on the tab indicated using a scribe [2]. c. Slide the ODD out of the computer [3].

Installing the Optical-disk Drive

1. Insert the ODD into its slot until it clicks into place.

2. Tighten the screw to secure the ODD.

3. Install the battery.

4. Follow the procedures in After Working Inside Your computer .

Removing the Access Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the access panel to the computer [1]. b. Lift the access panel partially at a 45–degree angle [2].

4. Remove the access panel from the computer.

Installing the Access Panel

1. Place the access panel to align with the screw holes at the back of the computer.

2. Tighten the screws to secure the access panel to the computer.

3. Install the battery.

4. Follow the procedures in After Working Inside Your computer .

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery b. access panel

3. Perform the following steps as shown in the illustration:

a. Disconnect the hard drive cable from the system board and lift it up to remove it from the

computer [1,2].

b. Remove the screws that secure the hard drive to the computer [3].

4. Perform the following steps as shown in the illustration:

a. Lift the hard drive to remove it from the computer [1,2].

5. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the hard drive to the bracket [1]. b. Lift the hard drive from the bracket [2].

Installing the Hard Drive

1. Place the hard drive in the bracket.

2. Tighten the screws that secure the hard drive to the bracket.

3. Slide the hard drive into the connector.

4. Tighten the screw to secure it to the chassis.

5. Install:

a. access panel b. battery

6. Follow the procedures in After Working Inside Your computer .

Removing the Memory Module

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery b. access panel

3. Pry the securing clips away from the memory module until it pops up.

4. Remove the memory module from its socket on the system board.

Installing the Memory Module

1. Insert the memory module into the socket and press to lock the securing clips.

2. Install:

a. access panel b. battery

3. Follow the procedures in After Working Inside Your computer .

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery b. access panel

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the WLAN card to the system board [1,2]. b. Remove the two connectors that secure the WLAN card to the system board [3]. c. Remove the WLAN card from its socket [4].

Installing the WLAN Card

1. Insert the WLAN card into its slot and tighten the screw to secure it to the system board.

2. Connect the two connectors (black cable to the black triangle and white cable to the white triangle).

3. Install:

a. access panel b. battery

4. Follow the procedures in After Working Inside Your computer

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery b. access panel

3. Push the coin-cell release latch using a scribe and then pull the coin-cell battery to remove it from

the computer.

Installing the Coin-cell battery

1. Insert the coin-cell battery and press to lock it.

2. Install:

a. access panel b. battery

3. Follow the procedures in After Working Inside Your computer .

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Release the keyboard by prying on the keyboard release tabs using a scribe.

4. Perform the following steps as shown in the illustration:

a. Slide and lift the keyboard to access the keyboard connector cable underneath [1,2].

5. Perform the following steps as shown in the illustration:

a. Disconnect the keyboard cable from the system board [1]. b. Lift the keyboard cable to remove it from the computer [2].

Installing the Keyboard

1. Connect the keyboard cable to the connector on the system board.

2. Slide the keyboard into the retention slots.

3. Press along the top edges to lock the keyboard in place.

4. Install the battery.

5. Follow the procedures in After Working Inside Your computer .

Removing the Base Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

+ 35 hidden pages