ALIENWARE® M17x
MOBILE MANUAL
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better
use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or
loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
e contents herein are subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the prior
written permission of Dell Inc. is strictly prohibited.
Trademarks used in this manual: Alienware, AlienFX, and the AlienHead logo
are trademarks or registered trademarks of Alienware Corporation; Dell is a
trademark of Dell Inc.; Microsoft and Windows are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries;
Intel and Intel SpeedStep are registered trademarks and Core is a trademark
of Intel Corporation in the U.S. and other countries; Blu-ray Disc is a trademark
of the Blu-ray Disc Association; Bluetooth is a registered trademark owned by
Bluetooth SIG, Inc.; Phoenix FailSafe is a trademark of Phoenix Technologies Ltd.
Other trademarks and trade names may be used in this manual to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Regulatory Model: P01E Regulatory Type: P01E002
P/N: W3D7V Rev. A00 November 2009
CONTENTS
INTRODUCTION ...........................................................5
CHAPTER 1: SETTING UP YOUR LAPTOP .................................... 7
Before Setting Up Your Laptop .......................................8
Connect the AC Adapter ..............................................9
Press the Power Button ..............................................9
Set Up Microsoft Windows...........................................10
Connect to the Internet (Optional) ...................................10
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP ............................ 13
Front View Features .................................................14
Back View Features..................................................14
Left View Features ..................................................15
Right View Features .................................................16
Display Features .................................................... 17
Computer Base and Keyboard Features ..............................18
Status Lights .......................................................19
Touch Controls......................................................19
Power Button ...................................................... 20
Function Keys ......................................................21
CHAPTER 3: USING YOUR LAPTOP.........................................23
Connecting External Displays ........................................24
Using Removable Media and Cards...................................25
Using the Optical Drive ..............................................25
Using the Integrated Camera ........................................26
Using the Wireless Control...........................................26
Battery Pack ........................................................26
Power Management.................................................26
Alienware Command Center .........................................27
Stealth Mode .......................................................27
Free Fall Sensor .................................................... 28
Conguring the BIOS ............................................... 28
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS ....33
Before You Begin................................................... 34
Replacing the Battery Pack ......................................... 36
Upgrading or Replacing Memory .....................................37
Upgrading or Replacing the Hard Drive(s) ........................... 39
CONTENTS
3
CHAPTER 5: TROUBLESHOOTING .........................................43
Basic Hints and Tips................................................ 44
Backup and General Maintenance................................... 44
Software Diagnostic Tools .......................................... 45
Answers to Common Problems ......................................47
CHAPTER 6: SYSTEM RECOVERY .......................................... 51
Dell DataSafe Local Backup ..........................................52
CHAPTER 7: BASIC SPECIFICATIONS .......................................53
APPENDIX A: GENERAL AND ELECTRICAL SAFETY PRECAUTIONS............57
APPENDIX B: CONTACTING ALIENWARE ...................................59
APPENDIX C: MACROVISION PRODUCT NOTICE.............................60
4
CONTENTS
INTRODUCTION
INTRODUCTION
Dear Valued Alienware Customer,
Welcome to the Alienware family. We are thrilled to include you among the
growing number of savvy high-performance computer users.
e Alienware technicians who have crafted your computer have made certain
that your high-performance computer is properly optimized and performs to its
fullest potential. We build computers with a single unwavering purpose: Build
It As If It Were Your Own. e technicians will not rest until your new computer
meets or exceeds our very demanding criteria!
We have tested your computer extensively in order to ensure that you enjoy
the highest levels of performance. In addition to a standard burn-in period,
your computer has been evaluated using real-world tools such as synthetic
performance benchmarks.
We invite you to share your experience with your new high-performance computer
with us, so do not hesitate to either e-mail or call Alienware with any questions
or concerns. e entire sta shares your enthusiasm for new technology and we
hope that you enjoy using your new computer as much as Alienware enjoyed
building it for you.
Sincerely,
Alienware Sta
INTRODUCTION
5
INTRODUCTION
6
CHAPTER 1: SETTING UP YOUR LAPTOP
CHAPTER 1: SETTING UP YOUR LAPTOP
CHAPTER 1: SETTING UP YOUR LAPTOP
7
Before Setting Up Your Laptop
Product Documentation and Media
Congratulations on the purchase of your Alienware® M17x!
Read all safety and setup instructions before connecting your new laptop. Begin
by carefully opening the box and removing all components that were shipped to
you. Before setting up your laptop or components, be sure to inspect all items
for any physical damage that may have occurred during shipment. Be sure to
report any damaged items to customer service immediately upon receiving your
shipment. You must report shipping damage within the rst 5 days of receiving
the shipment or your damage report will not be honored.
Before setting up your laptop or components, see the included invoice to verify
that all items ordered are present. Report any missing components to customer
service within 5 days of receiving the shipment. Anything reported missing after
the rst 5 days of receiving a shipment will not be honored. Some of the most
common items to check for include:
Laptop and AC adapter with power cable•
Microsoft CD-key located at the bottom of the laptop•
Monitor with power cable and video cable (if ordered)•
Keyboard (if ordered)•
Mouse (if ordered)•
Multimedia speakers and sub-woofer (if ordered)•
Joystick controllers (if ordered)•
You may also need a small athead and/or a Phillips head screwdriver for
connecting peripheral cables to the laptop.
e documentation that ships with your Alienware® laptop is designed to provide
answers to many of the questions that may arise as you explore your new laptop’s
capabilities. You may see the documentation for technical information or general
use as needed to answer questions in the future, or aid you in nding answers and
solutions. e media included with your laptop is referenced in some sections of
the documentation and may be needed to complete certain tasks. As always, our
technical support sta is available to assist you.
Placing Your Laptop
WARNING: Do not place the laptop near or over a radiator or heating vent.
If your laptop is placed in a cabinet, ensure that adequate ventilation
is provided. Do not place the laptop in a humid location or in any area
where the laptop may be exposed to rain or water. Be careful not to spill
liquid of any kind on or into the laptop.
When placing your laptop, ensure that:
It is placed on a surface that is both level and stable. •
e power and other cable connectors are not jammed between the laptop •
and a wall – or any other object.
Nothing obstructs airow in front of, behind, or below the laptop.•
e laptop has enough room so that optical drives and other external •
storage drives can be easily accessed.
CHAPTER 1: SETTING UP YOUR LAPTOP
8
Press the Power ButtonConnect the AC Adapter
WARNING: e AC adapter works with electrical outlets worldwide.
However, power connectors and power strips vary among countries.
Using an incompatible cable or improperly connecting the cable to a
power strip or electrical outlet may cause re or equipment damage.
NOTE: e AC adapter should be be connected to the laptop for maximum
gaming performance.
CHAPTER 1: SETTING UP YOUR LAPTOP
9
Set Up Microsoft Windows
CAUTION: Do not interrupt the operating system’s setup process. Doing
so may render your computer unusable.
Your computer is precongured with the operating system you requested
while ordering your computer. To congure the remaining settings, follow the
instructions on the screen.
Setting Up a Wireless Connection
NOTE: To set up your wireless router, see the documentation that shipped
with your router.
Before you can use your wireless Internet connection, you need to connect to your
wireless router.
To set up your connection to a wireless router:
NOTE: For optimal performance of your computer, it is recommended that
you download and install the latest BIOS and drivers for your computer
available at support.dell.com.
NOTE: For more information on the operating system and features, see
support.dell.com/MyNewDell.
Connect to the Internet (Optional)
Setting Up a Wired Connection
If you are using a dial-up connection, connect the telephone line to the •
optional external USB modem and to the telephone wall jack before you set
up your Internet connection.
If you are using a DSL or cable/satellite modem connection, contact your ISP •
or cellular telephone service for setup instructions.
To complete setting up your wired Internet connection, follow the instructions in
“Setting Up Your Internet Connection” on page 11.
CHAPTER 1: SETTING UP YOUR LAPTOP
10
Ensure that wireless is enabled on your computer.1.
Save and close any open les, and exit any open programs.2.
Click 3. Start → Control Panel→ Network and Sharing Center→
Connect to a network.
Follow the instructions on the screen to complete the setup.4.
Setting Up Your Internet Connection
ISPs and ISP oerings vary by country. Contact your ISP for oerings available in
your country.
If you cannot connect to the Internet but have successfully connected in the past,
the Internet Service Provider (ISP) might have a service outage. Contact your ISP
to check the service status, or try connecting again later.
Have your ISP information ready. If you do not have an ISP, the Connect to the
Internet wizard can help you get one.
Save and close any open les, and exit any open programs.1.
Click 2. Start → Control Panel.
Click 3. Network and Internet→ Network and Sharing Center→
Set up a new connection or Network→ Connect to the Internet.
e Connect to the Internet window appears.
NOTE: If you do not know which type of connection to select, click
Help me choose or contact your ISP.
Follow the instructions on the screen and use the setup information 4.
provided by your ISP to complete the setup.
CHAPTER 1: SETTING UP YOUR LAPTOP
11
CHAPTER 1: SETTING UP YOUR LAPTOP
12
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
CHAPTER 2: GETTING TO KNOW
is chapter provides information about your new laptop to familiarize you with
its various features, and get you up and running quickly.
YOUR LAPTOP
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
13
1
Front View Features
2 31
Back View Features
1 Left speaker — Combines with the right speaker to provide high quality
stereo sound.
2 Consumer IR port — Connects to devices using infrared.
3 Right speaker — Combines with the left speaker to provide high quality
stereo sound.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
14
1 AC adapter connector — Connects to the AC adapter to power the
computer and charge the battery.
Left View Features
21
3
4 5
6
7
8
4
DisplayPort connector — Connects your computer to external
monitors and projectors with DisplayPort.
1
2
3
Security cable slot — Attaches a commercially available security
cable to the computer.
NOTE: Before you buy a security cable, ensure that it works with the
security cable slot on your computer.
VGA connector — Connects to video devices, such as a monitor or
projector.
HDMI connector — Connects to a TV for both audio and video signals.
NOTE: For a monitor without built-in speakers, only the video signal will be
read.
5
6
7
8
Network connector — Connects your computer to a network or
broadband device.
USB connectors (2) — Connect to USB devices, such as a mouse,
keyboard, printer, external drive, or MP3 player.
USB/eSATA combo connector with USB PowerShare — Connects
to eSATA compatible storage devices (such as external hard drives or
optical drives) or USB devices (such as a mouse, keyboard, printer, external
drive, or MP3 player).
e USB Powershare feature allows you to charge USB devices when the
computer is turned o or in standby mode. If you turn o your computer
while charging a USB device, the device will stop charging. To continue
charging, disconnect the USB device and connect it again.
NOTE: Certain USB devices may not charge when the computer is turned
o or in standby mode. In such cases turn on the computer to charge the
device.
IEEE 1394 A connector — Connects to high-speed serial
multimedia devices such as digital video cameras.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
15
Right View Features
2
3
4 516 7 8
4
USB connectors (2) — Connect to USB devices, such as a mouse,
keyboard, printer, external drive, or MP3 player.
1 8-in-1 Media Card Reader — Provides a fast and convenient way to view
and share digital photos, music, videos, and documents.
2 ExpressCard slot — Provides support for additional memory, wired and
wireless communications, multimedia, and security features. e slot
supports 54 mm Express cards.
NOTE: e ExpressCard slot is designed only for ExpressCards. e slot
does NOT support PC Cards.
3 Optical drive — Plays or records only standard-size (12 cm) CDs, DVDs, and
Blu-ray Discs (optional). Ensure that the side with print or writing is facing
upward when inserting discs. For more information, see “Using the Optical
Drive“ on page 25.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
16
5
6
7
8
Audio out/Headphone connector — Connects to front L/R speakers
or headphones.
Audio out/Headphone connector — Connects to a center speaker/
subwoofer or headphones.
Rear L/R surround connector — Connects to rear L/R surround
speakers.
Audio in/Microphone connector — Connects to a microphone for
voice or audio input into a sound or telephony program.
Display Features
1
2
3
4
1 Left digital-array microphone — Combines with the right digital-array
microphone to provide high quality sound for video chatting and voice
recording.
2 Camera — Built-in camera for video capture, conferencing, and chat.
3 Camera activity indicator — Indicates if the camera is on or o.
4 Right digital-array microphone — Combines with the left digital-array
microphone to provide high quality sound for video chatting and voice
recording.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
17
Computer Base and Keyboard Features
6
5
4
1
3
2
1 Status lights (3) — Indicate if the Scroll Lock, Caps Lock, or Number Lock
lights are turned on or o.
2 Keyboard — e backlit keyboard provides visibility in dark environments
by illuminating all symbols on the keys.
3 Touch pad — Provides the functionality of a mouse to move the cursor,
drag or move selected items, and left-click by tapping the surface.
4 Touch pad buttons (2) — Provide left- and right-click functions like those
on a mouse.
5 Touch controls (9) — Touching the touch controls perform the associated
action. For more information, see “Touch Controls” on page 19.
6 Power button — Turns the computer on or o when pressed. For more
information, see “Power Button” on page 20.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
18
Status Lights
Touch Controls
e three status lights are located at the top-left side of the keyboard. For the
exact location, see “Computer Base and Keyboard Features” on page 18.
Scroll Lock Light
Turns on when the scroll lock option is on.
Caps Lock Light
Turns on when the keyboard is in Caps Lock mode.
In this mode, all characters you type are in uppercase.
Number Lock Light
Turns on when the keyboard is in Num Lock mode.
In this mode, the embedded numeric keypads can be used.
e touch controls are located at the top of the keyboard. For the exact location,
see “Computer Base and Keyboard Features” on page 18. To activate, gently
touch the desired control. e control will illuminate temporarily to conrm your
selection.
Eject Increase volume
Rewind or Play previous
track
Play or Pause Alienware Command Center
Fast Forward or Play
next track
Decrease volume
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
Wireless Control - Switch
wireless communications on/o
(for more information, see “Using
the Wireless Control” on page 26)
(for more information, see
“Alienware Command Center” on
page 27)
Stealth Mode - Switch computer
to low power state
(for more information, see
“Stealth Mode” on page 27)
19
Power Button
You can program this button to perform actions like shutting down the operating
system or entering the standby mode. For details on how to program this button,
see Power Options in the Control Panel of Microsoft® Windows® operating
system.
e power button is located in the center of the hinge cover. For the exact location,
see “Computer Base and Keyboard Features” on page 18.
e color of the AlienHead rim indicates the power status. e color indicating
the power status can be changed through the AlienFX® software.
On AC adapter:
Blue or custom AC-color e battery is fully charged.
Blue or custom AC-color fading
into amber or custom batterycolor
Blue or custom AC-color fading
into black
On battery:
Amber or custom battery-color e battery is fully charged.
Amber or custom battery-color
fading into black
Blinking Amber or custom
battery-color
For more details on standby and hibernate mode, see the Power Options in the
Control Panel of your Microsoft Windows operating system.
e battery is charging.
e computer is in standby
mode.
e computer is in standby
mode.
e battery charge is low.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
20
Function Keys
NOTE: Depending on the conguration of the laptop you purchased, some
of the function keys may have no associated tasks.
e <Fn> key is located near the bottom-left corner of the keyboard, and is used
together with other keys to activate certain functions. Hold down the <Fn> key
along with the key described below:
FI – Suspend Mode
Press <Fn><F1> to enable suspend mode. In the suspend mode,
the display and selected devices will switch o for less energy
consumption.
F2 – Check Battery Status and Battery Charge Disable/Enable
Press <Fn><F2> to toggle between the Battery Status Meter,
Battery Charge Disable feature, and Battery Charge Enable feature.
F6 – Extend Desktop
Press <Fn><F6> to switch between the various external display
options available either simultaneously or separately.
F7 – Display Mode
Press <Fn><F7> to switch between clone mode and extended
desktop mode, when an external display is connected.
F9 – Camera on/o
Press <Fn><F9> to switch o or switch on the camera.
F10 – Microsoft Mobility Center on/o
Press <Fn><F10> to launch or close the Microsoft Mobility Center
application.
F11 – AlienFX® on/o
Press <Fn><F11> to disable or enable the AlienFX illumination.
F3 – Mute on/o
Press <Fn><F3> to enable or disable the mute function.
F4 – Increase Display Brightness
Press <Fn><F4> to increase the brightness of the display.
F5 – Decrease Display Brightness
Press <Fn><F5> to decrease the brightness of the display.
F12 –Touch Pad on/o
Press <Fn><F12> to enable or disable the touch pad function
and the illumination around the touch pad. When the touch pad
function is switched o, the touch pad can still work temporarily
for three to ve seconds while the computer reboots into
the Windows® operating system, or resumes from standby or
hibernate mode.
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
21
CHAPTER 2: GETTING TO KNOW YOUR LAPTOP
22
CHAPTER 3: USING YOUR LAPTOP
CHAPTER 3: USING YOUR LAPTOP
CHAPTER 3: USING YOUR LAPTOP
23
Connecting External Displays
If you want to enjoy your computing environment on a bigger scale visually,
or extend your desktop area, you can connect an external display such as a
standalone monitor, an LCD TV, or a projector.
Connecting a Display
Use the appropriate cable based on the connectors available on your computer
and display. Refer to the following table to identify the connectors on your
computer and display.
Turn o your laptop.1.
Turn o the display and disconnect it from the power supply.2.
Connect one end of the display cable to the DisplayPort, HDMI, or VGA 3.
connector on your Alienware laptop.
Connect the other end of the cable to the same connector on your display.4.
If necessary, connect one end of the power cable to the display’s power 5.
connector.
Connect the other end of the power cable to a grounded three-prong power 6.
strip or wall outlet.
Turn on your laptop, and then turn on your display.7.
Connection Type Computer Cable Display
VGA-to-VGA
(VGA cable)
HDMI-to-HDMI
(HDMI cable)
HDMI-to-DVI
(HDMI-to-DVI
adapter + DVI cable)
DisplayPortto-DisplayPort
(DisplayPort cable)
CHAPTER 3: USING YOUR LAPTOP
24
Extending the Desktop
With the external display connected, right-click on the desktop and select 1.
Personalize.
Select 2. Connect to a projector or other external display in the upper left
portion of the screen.
Click 3. Connect Display.
Select from the below options that appear on the screen:4.
Duplicate my display on all displays (mirrored)•
Show dierent parts of my desktop on each display (extended)•
Show my desktop on the external display only•
Click 5. Apply to apply your changes and then click OK to exit the Display
Settings control panel.
Using Removable Media and Cards
Using the Optical Drive
Observe the safety measures below:
When no ExpressCard or Media Card (SD/MMC/MS cards) is inserted into the
ExpressCard or Media Card slot, ensure that the blank cards that shipped with
your laptop is inserted in the unused slot(s). e blank cards protect the unused
slots from dust and other particles. When inserting a blank card, ensure that
the correct side is on the top (indicated by an arrow mark on some blank cards).
Inserting a blank card upside down may damage your laptop.
Your laptop has a slot load optical drive. Depending on the conguration ordered,
your laptop may have one of the following drive types. ese logos are used to
indicate each drive’s capabilities and media compatibility.
DVD±R/W Dual
Layer Writer
Blu-ray Disc™
Reader/Writer
DVD±R/W drive can read CD-ROM, CD-R, CD-R/W, DVD,
DVD+R/W, and DVD-R/W media.
It can also record to CD-R, CD-RW, DVD+R/W, DVD-R/W,
and DVD+R Dual Layer (DL) media.
Blu-ray drive can read CD-ROM, CD-R, CD-R/W, DVD,
DVD+R/W, DVD-R/W, DVD+R Dual Layer (DL), BD-ROM,
BD-R, and BD-RE media.
It can also record to CD-R, CD-R/W, DVD+R/W, DVD-R/W,
DVD+R Dual Layer (DL), BD-R, and BD-RE media.
CHAPTER 3: USING YOUR LAPTOP
25
Using the Integrated Camera
Turning the Camera On and O
Press the key combination <Fn><F9> to switch on or switch o the camera. After
switching on the camera, you need to activate its function through the Microsoft
Windows operating system. In addition, you can also use Windows Movie Maker
to create, edit, and share videos.
Using the Wireless Control
e wireless control allows you to quickly turn all of your wireless radios
(Bluetooth® and WLAN) o, such as when you are asked to disable all wireless
radios on an airplane ight. Gently touching this control one time turns all of your
radios o. Gently touching it again returns your wireless radios to their respective
states they were in before you touched the control the rst time.
e battery meter lights on the battery pack indicate the charge level of the
battery. When you press the battery meter once, the charge level lights illuminate.
Each of the ve lights represent approximately 20% of the total battery charge.
For example, if four lights turn on, there is 80% of battery charge remaining and if
no lights turn on, there is no charge remaining in the battery.
Power Management
Understanding Power Consumption
In order to fully utilize the power of your battery, it would be a good idea for you
to spend some time acquiring a basic understanding of the power management
concept from your operating system.
You can use the power options in your operating system to congure the power
settings on your computer. e Microsoft® Windows® operating system installed
on your computer provides three default options:
Battery Pack
Your laptop is equipped with a high-energy rechargeable lithium ion (Li-ion)
battery pack. Battery life will vary depending on your laptop conguration, model,
applications installed, power management settings, and features used. As with
all batteries, the maximum capacity of this battery will decrease with time and
usage.
CHAPTER 3: USING YOUR LAPTOP
26
Balanced — Oers full performance when you need it and saves power •
during periods of inactivity.
Power Saver — Saves power on your computer by reducing system •
performance to maximize the life of the computer and by reducing the
amount of energy consumed by your computer over its lifetime.
High Performance — Provides the highest level of system performance •
on your computer by adapting processor speed to your activity and by
maximizing system performance.
Customizing Your Power Settings:
Alienware Command Center
Click 1. Start → Control Panel.
Click 2. All Control Panel Items.
Double-click the 3. Power Options icon.
Select a power plan from the options shown. To customize specic settings, 4.
click Change plan settings next to the selected power plan.
Reducing Power Consumption
Although your laptop (together with the operating system) is capable of
power conservation, there are measures you can take to reduce the power
consumption:
Use the AC power whenever possible.•
Lower the intensity of the display backlight. A very bright screen translates •
to higher power usage.
Switch to the Stealth mode to activate additional system power savings. •
Switching into and out of Stealth mode may require a reboot depending on
your computer conguration and the operating system.
NOTE: e battery pack should be locked in the battery compartment all
the time.
e Alienware® Command Center gives you access to Alienware’s exclusive
software and is a continuously upgradable control panel. As Alienware releases
new programs, they download directly into the Command Center allowing you
to build a library of system management, optimization, and customization tools.
You can access Alienware Command Center by gently touching the touch control
located near the top of the keyboard. e control will illuminate temporarily to
conrm your selection. For the exact location of the control, see “Computer Base
and Keyboard Features” on page 18.
Stealth Mode
Stealth mode is designed to reduce the processor and graphics utilization and
thereby reduces the energy consumption and noise level of your computer.
NOTE: Stealth mode has no eect while the computer is running on
battery power.
You can access Stealth mode by gently touching the touch control located near
the top of the keyboard. e control will illuminate to full brightness until the
function is deactivated. For the exact location of the control, see “Computer Base
and Keyboard Features” on page 18.
CHAPTER 3: USING YOUR LAPTOP
27
Free Fall Sensor
Free fall sensor protects your computer hard drive from possible damage, by
detecting a free fall state caused by accidentally dropping the computer. When a
free fall state is detected, the hard drive is placed in a safe state to protect against
damage to the read/write head and possible data loss. Your hard drive returns to
normal operation, when the free fall state is no longer detected.
Entering System Setup
Turn on (or restart) your laptop.1.
While the laptop is booting, press <F2> immediately before the operating 2.
system logo appears to access the BIOS Setup Utility.
If an error occurs during POST (Power On Self Test), you may also enter the
BIOS Setup Utility by pressing <F2> when prompted.
Conguring the BIOS
System Setup
e System Setup options allow you to:
Change the system conguration information after you add, change, or •
remove any hardware in your laptop.
Set or change a user-selectable option.•
View the installed amount of memory or set the type of hard drive installed.•
Before you use System Setup, it is recommended that you write down the current
System Setup information for future reference.
CAUTION: Do not change the settings in System Setup unless you are
an expert computer user. Certain changes can cause your computer to
work incorrectly.
CHAPTER 3: USING YOUR LAPTOP
28
NOTE: If you wait too long and the operating system logo appears, continue
to wait until you see the Microsoft® Windows® desktop, then shut down
your laptop and try again.
NOTE: Keyboard failure may result when a key on the keyboard is held down
for extended periods of time. To avoid possible keyboard failure, press and
release <F2> in even intervals until the System Setup screen appears.
System Setup Screens
e BIOS Setup Utility window displays current or changeable conguration
information for your laptop. Information is divided into ve menus: Main,
Advanced, Security, Boot, and Exit.
Key functions appear at the bottom of the BIOS Setup Utility window and lists
keys and their functions within the active eld.
System Setup Options
NOTE: Depending on your computer and installed devices, the items listed
in this section may not appear, or may not appear exactly as listed.
NOTE: For the updated system setup information, see the Service Manual
at support.dell.com/manuals.
Main Menu
System Time
System Date
Alienware
Service Tag
BIOS Version
EC Version
CPU
CPU Speed
CPU Cache
CPU ID
Displays the system time.
Displays the system date.
Displays the model number of your computer.
Displays the service tag of your computer.
Displays the BIOS revision.
Displays the EC rmware version.
Displays the type of processor.
Displays the speed of the processor.
Displays the processor cache size.
Displays the ID of the processor.
Main Menu
Total Memory
Memory Bank 0
Memory Bank 1
Advanced Menu
Wired Network
Wireless
Network
Bluetooth
Receiver
Displays the total memory available in your computer.
Displays the memory size installed in memory bank 0.
Displays the memory size installed in memory bank 1.
Allows you to enable or disable the on-board LAN
controller.
Disabled: Internal LAN is disabled and is not visible to •
the operating system.
Enabled: Internal LAN is enabled. •
Allows you to enable or disable the internal wireless
device.
Disabled: e internal wireless device is disabled and •
is not visible to the operating system.
Enabled: e internal wireless device is enabled.•
Allows you to enable or disable the internal Bluetooth
device.
Disabled: e internal Bluetooth device is disabled •
and is not visible to the operating system.
Enabled: e internal Bluetooth device is enabled.•
CHAPTER 3: USING YOUR LAPTOP
29
Advanced Menu
High
Denition
Sound
USB Emulation
Firewire
Performance
Options
Allows you to enable or disable the internal high denition
audio device.
Disabled: e internal audio device is disabled and is •
not visible to the operating system.
Enabled: e internal audio device is enabled.•
Allows you to enable or disable the USB emulation
feature. is feature denes how the BIOS, in the absence
of a USB-aware operating system, handles USB devices.
USB emulation is always enabled during POST (Power On
Self Test).
NOTE: You cannot boot any type of USB device (oppy,
hard drive, or memory key) when this option is o.
Allows you to enable or disable the IEEE 1394 A connector.
Disabled: e IEEE 1394 A connector is disabled and is •
not visible to the operating system.
Enabled: e IEEE 1394 A connector is enabled.•
Allows you to congure elds in the Performance Options
sub-menu (for more information, see “Performance
Options Sub-Menu“ on page 31).
Advanced Menu
SATA
Operation
SATA Hard
Drive 1
SATA Hard
Drive 2
SATA Optical
Drive
Allows you to congure the operating mode of the
integrated SATA hard drive controller.
ATA: SATA is congured for ATA mode.•
AHCI: SATA is congured for AHCI mode.•
RAID: SATA is congured for RAID mode.•
Displays the installed primary SATA hard drive model.
Displays the installed secondary SATA hard drive model.
Displays the installed SATA optical drive model.
CHAPTER 3: USING YOUR LAPTOP
30
Performance Options Sub-Menu
CPU Speed
Memory
Displays the speed of the processor.
Displays the frequency of the memory.
Frequency
Memory
Channel Mode
Displays the memory channel modes.
Single•
Dual•
CPU
Indicates if the processor is in turbo mode or not.
Performance
Mode
Turbo Mode
DDR3 Voltage
CPU Vcore
CPU
Frequency
Allows you to enable or disable the turbo mode.
Allows you to enter the memory voltage.
Allows you to set the processor Vcore voltage.
Allows you to congure the processor over-clocking
frequency.
OverClocking
Security Menu
System
Password
Status
Set System
Password
User
Password
Status
Set User
Password
Enable
Password on
Boot
Failsafe
Asset Tag
Displays the status of the system password. e system
password is also known as the Master/Supervisor
password.
Enabled: e system password is enabled.•
Not Enabled: e system password is not enabled. •
Allows you to set the system password. e system
password controls access to the system setup utility.
Displays the status of the user password.
Enabled: e user password is enabled and the built-in •
PS/2 compatible mouse controller is enabled.
Not Enabled: e user password is not enabled and the •
built-in PS/2 compatible mouse controller is disabled.
Allows you to set the user password. e user password
controls access to the computer at boot.
Allows you to enable or disable password entry on boot.
Allows you to enable or disable the Phoenix FailSafe™
security software to protect, track, and manage your laptop
and your digital les if your laptop is lost or stolen.
Displays the asset tag.
CHAPTER 3: USING YOUR LAPTOP
31
Power Menu
A/C Adapter
Displays the AC adapter rating.
Rating
A/C Adapter
Warnings
Allows you to choose if the computer should display
warning messages when you use certain power adapters.
e computer displays these messages if you attempt to
use a power adapter that has too little capacity for your
conguration.
USB Wake
Support
USB Power
Share
Allows you to enable USB devices to wake the computer from
standby mode or to disable the USB wake support feature.
Allows you to enable USB-chargeable devices to charge when
the computer is turned o or in standby mode or to disable
the USB power share feature.
Boot Menu
Use the plus (+) or minus (-) keys to change the boot device priority. You can
choose from:
Hard Drive•
USB Storage•
CD\DVD\BD•
Removable Devices•
Network•
Exit Menu
Exit Saving
Changes
Exit
Discarding
Changes
Load Setup
Defaults
Discard
Changes
Save
Changes
Allows you to exit System Setup and save your changes to
CMOS.
Allows you to exit utility without saving System Setup data
to CMOS.
Allows you to load default values for all System Setup items.
Allows you to load previous values from CMOS for all System
Setup items.
Allows you to save System Setup data to CMOS.
CHAPTER 3: USING YOUR LAPTOP
32
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
CHAPTER 4: INSTALLING ADDITIONAL
OR REPLACEMENT COMPONENTS
is chapter provides guidelines and instructions for increasing the
processing power and storage space, by upgrading equipment. You
can purchase components for your computer at www.dell.com or
www.alienware.com.
NOTE: See the Service Manual at support.dell.com/manuals for
installation instructions of all serviceable components. Parts purchased
from Dell and Alienware will ship with specic replacement instructions.
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
33
Before You Begin
Turning O Your Computer
is section provides procedures for removing and installing the components in
your laptop. Unless otherwise noted, each procedure assumes that the following
conditions exist:
You have performed the steps in “Turning O Your Computer” and “Before •
Working Inside Your Computer” in this section.
You have read the safety information that shipped with your computer.•
A component can be replaced or—if purchased separately—installed by •
performing the removal procedure in reverse order.
CAUTION: To avoid losing data, save and close all open les and exit all
open programs before you turn o your laptop.
Save and close all open les and exit all open programs. 1.
Click 2. Start → Shut Down.
e laptop turns o after the operating system shutdown process nishes.
Ensure that the computer is turned o. If your computer did not 3.
automatically turn o when you shut down your operating system, press
and hold the power button until the computer turns o.
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
34
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential
damage and to help to ensure your own personal safety.
WARNING: Before working inside your laptop, read the safety
information that shipped with your computer. For additional safety best
practices information, see the Regulatory Compliance Homepage at
www.dell.com/regulatory_compliance.
CAUTION: Handle components and cards with care. Do not touch the
components or contacts on a card. Hold a card by its edges. Hold a
component such as a processor by its edges, not by its pins.
CAUTION: Only a certied service technician should perform repairs on
your computer. Damage due to servicing that is not authorized by Dell is
not covered by your warranty.
CAUTION: To avoid electrostatic discharge, ground yourself by using a
wrist grounding strap or by periodically touching an unpainted metal
surface (such as a connector on the back of the computer).
CAUTION: When you disconnect a cable, pull on its connector or on its
pull-tab, not on the cable itself. Some cables have connectors with locking
tabs; if you are disconnecting this type of cable, press in on the locking
tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before
you connect a cable, ensure that both connectors are correctly oriented
and aligned.
CAUTION: To avoid damaging the computer, perform the following steps
before you begin working inside the computer.
Ensure that the work surface is at and clean to prevent the computer cover 1.
from being scratched.
Turn o your computer (see “Turning O Your Computer” on page 2. 34).
CAUTION: To disconnect a network cable, rst unplug the cable from
your computer and then unplug the cable from the network device.
Disconnect all telephone or network cables from the laptop. 3.
Press and eject any installed cards from the ExpressCard slot and the Media 4.
Card slot.
Disconnect your computer and all attached devices from their electrical 5.
outlets.
CAUTION: To help prevent damage to the system board, you must remove
the battery from the battery bay before you service the laptop.
Remove the battery from the battery bay (see “Replacing the Battery Pack” 6.
on page 36).
Press the power button to ground the system board.7.
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
35
Replacing the Battery Pack
2
3
1
is battery pack can easily be removed and replaced. Ensure that the laptop is
properly shut down before changing the battery pack.
CAUTION: To avoid damage to the laptop, use only the battery designed
for this particular Alienware laptop. Do not use batteries designed for
other Alienware or Dell laptops.
To remove the battery pack:
Follow the instructions in “Before You Begin” on page 1. 34.
Shut down the laptop.2.
Turn the laptop over.3.
Slide the battery latch to the unlock position as shown.4.
e battery pack will pop up.5.
Remove the battery pack.6.
To replace the battery pack:
Follow the instructions in “Before You Begin” on page 1. 34.
Align the three battery pack tabs with the slots in the battery bay.2.
Push the battery pack into the battery bay until the battery pack clicks 3.
into place.
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
36
1 battery bay 3 battery latch
2 battery pack
Upgrading or Replacing Memory
1
2
Your laptop is equipped with a congurable memory unit. e industry standard
JEDEC DDR3 SODIMM memory module connectors are available for memory
upgrade. e table below illustrates all the possible ways system memory can be
congured.
Memory connector #1 Memory connector #2 Total Memory
2 GB 2 GB 4 GB
2 GB 4 GB 6 GB
4 GB 2 GB 6 GB
4 GB 4 GB 8 GB
Removing the Memory Module(s)
Follow the instructions in “Before You Begin” on page 1. 34.
Remove the battery pack (see “Replacing the Battery Pack“ on page 2. 36).
Loosen the two captive screws that secure the compartment door to the 3.
computer base.
Slide the compartment door towards the front of the computer and then lift 4.
it up.
1 compartment door 2 captive screws (2)
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
37
5
4
2
3
1
Loosen the captive screw that secures the memory-module door to the 5.
2
1
computer base.
Slide the memory-module door to release the tabs and lift the 6.
memory-module door out of the computer base.
1 captive screw 2 memory-module door
Use your ngertips to carefully spread apart the memory-module 7.
connector’s spring-locks until the memory module pops up.
Remove the memory module.8.
38
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
1 memory module 4 notch
2 spring locks (2) 5 memory-module connector
3 tab
To replace the memory modules, perform the removal steps in reverse order.
While inserting the memory module into the memory-module connector, align
the notch on the memory module to the tab on the memory-module connector.
NOTE: Install the memory module rst in the bottom connector and then
in the top connector.
NOTE: If the memory module is not installed properly, the computer may
not boot.
Upgrading or Replacing the Hard Drive(s)
1
2
Your laptop is equipped with two hard drive sockets.
Removing the Hard Drive(s)
Follow the instructions in “Before You Begin” on page 1. 34.
Remove the battery pack (see “Replacing the Battery Pack“ on page 2. 36).
Loosen the two captive screws that secure the compartment door to the 3.
computer base.
Slide the compartment door towards the front of the computer and then lift 4.
it up.
1 compartment door 2 captive screws (2)
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
39
3
1
2
Loosen the four captive screws on the primary hard drive (HDD0).5.
1
3
2
Slide the primary hard drive (HDD0) towards the back using the pull tab and 6.
lift the primary hard drive out of the computer base.
Loosen the four captive screws on the secondary hard drive (HDD1).7.
Using the pull tab, lift the secondary hard drive (HDD1) out of the computer 8.
base.
1 primary hard drive 3 captive screws (4)
2 pull tab
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
40
1 secondary hard drive 3 captive screws (4)
2 pull tab
1
2
Remove the four screws that secure the hard drive to the hard-drive bracket.9.
3
1
2
Remove the interposer from the hard drive.11.
Lift the hard drive out of the hard-drive bracket.10.
1 hard drive 3 screws (4)
2 hard-drive bracket
1 interposer 2 hard drive
To replace the hard drive(s), perform the removal steps in reverse order.
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
41
CHAPTER 4: INSTALLING ADDITIONAL OR REPLACEMENT COMPONENTS
42
CHAPTER 5: TROUBLESHOOTING
CHAPTER 5: TROUBLESHOOTING
CHAPTER 5: TROUBLESHOOTING
43
Basic Hints and Tips
Backup and General Maintenance
Computer does not power on: Is your AC adapter cable securely connected •
to a working electrical outlet? If connected to a power strip, ensure that the
strip is actually working.
Connections: Check all the cables to ensure that there are no loose •
connections anywhere.
Power Savings: Ensure that your computer is not in hibernate or standby •
mode by pressing the power button for less than 4 seconds. e power
status light will fade from blue to black while in standby mode; in hibernate
mode it will be o.
Brightness: Check and adjust the brightness of the display by pressing the •
key combinations <Fn><F4> or <Fn><F5>.
Display Choice: Press the key combination <Fn><F6> to ensure that the •
computer is not set to “External Only” display.
Use only the AC adapter that shipped with your laptop.•
CHAPTER 5: TROUBLESHOOTING
44
Always backup your important data on a regular basis and keep copies of •
your operating system and software safe. Do not forget to note the serial
numbers if you are storing them outside of their original cases - e.g., in a CD
wallet.
Run maintenance programs as often as you can. You may schedule these •
programs to run at times when you are not using your computer. You can
use those provided with your operating system, or buy more powerful,
dedicated programs to do so.
Write down your passwords and keep them safe (away from your computer). •
is is especially important if you choose to password-protect your
computer’s BIOS and operating system.
Document vital settings such as network, dialup, mail and Internet settings.•
When troubleshooting your computer, remember the following safety guidelines:
Before touching any of the computer’s internal components, touch an •
unpainted portion of the chassis. Doing so will safely discharge any static
electricity, which could damage your computer.
Turn o your computer and any connected peripherals. •
Disconnect any peripherals from your computer. •
ings to check before troubleshooting:
Ensure that the AC adapter cable is properly connected between your •
computer and a grounded, three-prong power outlet. Ensure that the power
outlet is working.
Ensure the UPS or power strip is turned on (if applicable). •
If your peripheral devices (e.g. keyboard, mouse, printer, etc.) are not •
working, ensure that all connections are secure.
If any computer components were added or removed before the problem •
began, check to see if you performed the installation or removal procedures
properly.
If an error message appears on the screen, write down the exact error •
message prior to calling Technical Support to aid in diagnosing and
resolving your issue.
If an error occurs in a specic program, see the program’s documentation. •
Software Diagnostic Tools
Pre-Boot System Assessment (PSA)
e computer runs the Pre-boot System Assessment (PSA), a series of initial tests
of your system board, keyboard, display, memory, hard drive, etc.
To invoke PSA:
Turn on (or restart) your computer.1.
Press <F12> to access the 2. Boot Menu.
Select 3. Diagnostics from the menu and press <Enter>.
During the assessment, answer any questions that appear.
If a failure is detected, the computer stops and beeps. To stop the •
assessment and restart the computer, press <n>; to continue to the next
test, press <y>; to retest the component that failed, press <r>.
If failures are detected during the Pre-boot System Assessment, write down •
the error code(s) and contact Alienware (see “CONTACTING ALIENWARE“ on
page 59).
If the Pre-boot System Assessment completes successfully, the following message
appears “Do you want to run the remaining memory tests? This
will take about 30 minutes or more. Do you want to continue?
(Recommended).”
If you are experiencing memory issues, press <y> else press <n>. e following
message is displayed: “Pre-boot System Assessment complete.”
Press <o> to reboot your computer.
CHAPTER 5: TROUBLESHOOTING
45
Alienware® Diagnostics
Starting Alienware Diagnostics From the Resource Disc
If you experience a problem with your Alienware laptop, run the Alienware
Diagnostics before you contact Alienware for technical assistance. It is
recommended that you print these procedures before you begin.
NOTE: Back up all data before initiating a system recovery. It is
recommended to backup critical les onto an external media before
initiating recovery.
NOTE: e Resource disc contains drivers for your computer. You can
also download the latest drivers and software for your computer from
support.dell.com.
Review your laptop’s conguration information, and ensure that the device that
you want to test displays in the system setup program and is active. Start the
Alienware Diagnostics from the Resource disc.
Insert the Resource disc. 1.
Shut down and restart the laptop. 2.
When the Alienware logo appears, press <F12> immediately.
NOTE: If you wait too long and the operating system logo appears, continue
to wait until you see the Microsoft® Windows® desktop; then, shut down
your computer and try again.
NOTE: e next steps change the boot sequence for one time only. On the
next start-up, the computer boots according to the devices specied in
the system setup program.
When the boot device list appears, highlight 3. CD/DVD/CD-RW and
press <Enter>.
Select 4. Boot from CD-ROM from the menu that appears and press <Enter>.
Select 5. Alienware Diagnostics from the numbered list. If multiple versions
are listed, select the version appropriate for your computer.
When the Alienware Diagnostics 6. Main Menu appears, select the test you
want to run.
NOTE: Write down any error codes and problem descriptions exactly as
they appear and follow the instructions on the screen.
After all tests have completed, close the test window to return to the 7.
Alienware Diagnostics Main Menu.
Remove your Resource disc, then close the 8. Main Menu window to exit the
Alienware Diagnostics and restart the computer.
CHAPTER 5: TROUBLESHOOTING
46
Answers to Common Problems
System
e computer fails the POST
e POST (Power On Self Test) tests the computer, ensuring that it meets the
necessary system requirements and that all hardware is working properly before
starting the remainder of the boot process. If the computer passes the POST, the
computer will continue to start normally. However, if the computer fails the POST,
the computer will generate a single beep to indicate a general failure and an
error message will be displayed. For assistance, contact Technical Support (see
“CONTACTING ALIENWARE“ on page 59).
e computer stops responding or a solid blue screen appears
CAUTION: You might lose data if you are unable to perform an operating
system shutdown.
If you are unable to get a response by pressing a key on your keyboard or moving
your mouse, press and hold the power button for at least 6 seconds until the
computer turns o, then restart your computer.
NOTE: e chkdsk program may run when you restart the computer. Follow
the instructions on the screen.
A program stops responding or crashes repeatedly
End the program:
Press <Ctrl><Shift><Esc> simultaneously. 1.
Click the 2. Applications tab and select the program that is no longer
responding.
Click 3. End Task.
Check the software documentation.
If necessary, uninstall and then reinstall the program.
A program is designed for an earlier version of Microsoft® Windows®
Run the Program Compatibility Wizard:
e Program Compatibility Wizard congures a program so that it runs in an
environment similar to an earlier version of Microsoft Windows operating system
environments.
Click 1. Start → Control Panel→ Programs→ Programs and Features→
Use an older program with this version of Windows.
In the welcome screen, click 2. Next.
Follow the instructions on the screen.
CHAPTER 5: TROUBLESHOOTING
47
Other software problems
Back up your les immediately
Use a virus-scanning program to check the hard drive, or CDs
Verify that the device drivers do not conict with the program.•
If necessary, uninstall and then reinstall the program.•
Hard Drive Problems
Save and close any open les or programs and shut down your computer
through the Start menu
Scan the computer for spyware:
If you are experiencing slow computer performance, you frequently receive
pop-up advertisements, or you are having problems connecting to the Internet,
your computer might be infected with spyware. Use an anti-virus program that
includes anti-spyware protection (your program may require an upgrade) to scan
the computer and remove spyware.
Run the PSA Diagnostics:
If all tests run successfully, the error condition is related to a software problem.
Check the software documentation or contact the software manufacturer for
troubleshooting information:
Ensure that the program is compatible with the operating system installed •
on your computer.
Ensure that your computer meets the minimum hardware requirements •
needed to run the software. See the software documentation for
information.
Ensure that the program is installed and congured properly.•
CHAPTER 5: TROUBLESHOOTING
48
Allow the computer to cool before turning it on
A hot hard drive may prevent the operating system from starting. Try allowing
the computer to return to room temperature before turning it on.
Run Check Disk
Click 1. Start → Computer.
Right-click 2. Local Disk C:.
Click 3. Properties→ Tools→ Check Now.
If the User Account Control window appears, click Continue.
Follow the instructions on the screen.
Memory
Power
Memory errors detected on startup
Check memory modules for correct seating and orientation. Reseat the •
memory modules if applicable (see “Upgrading or Replacing Memory” on
page 37).
Computers using a dual-channel memory conguration require that •
memory modules be installed in pairs. If you require assistance, contact
Technical Support (see “CONTACTING ALIENWARE“ on page 59).
Display
If the display is blank
NOTE: If you are using a program that requires a higher resolution than
your computer supports, it is recommended that you attach an external
monitor to your computer.
e computer may be in a power saving mode:
Press a key on the keyboard or press the power button to resume normal
operation.
Switch the video image:
If your computer is attached to an external monitor, press <Fn><F6> to switch
the video image to the display.
When you press the power button, the computer does not turn on
If the AC adapter cable is connected to a surge protector or UPS, ensure that •
the surge protector or UPS is securely connected to an electrical outlet, is
switched on and is working correctly.
Check that the wall outlet is working properly by testing another device •
such as a radio or lamp that you know works. If the wall outlet is not working,
contact an electrician or your power company for further assistance.
If the problem persists, contact Alienware support (see “CONTACTING
ALIENWARE“ on page 59).
CHAPTER 5: TROUBLESHOOTING
49
CHAPTER 5: TROUBLESHOOTING
50
CHAPTER 6: SYSTEM RECOVERY
CHAPTER 6: SYSTEM RECOVERY
Your computer ships with the following media:
Operating System disc• — Contains operating system installation media.
Resource disc• — Contains drivers for your computer. You can also download
the latest drivers and software for your computer
from support.dell.com.
CHAPTER 6: SYSTEM RECOVERY
51
Dell DataSafe Local Backup
Dell DataSafe Local Backup is a backup and recovery application that can restore
your computer if you lose data due to a virus attack, accidentally delete critical
les or folders, or if the hard drive crashes.
is application allows you to:
Restore les and folders•
Restore your hard drive to the operating state it was in when you purchased •
your computer, without erasing the existing personal les and data
To schedule backups:
Double-click the Dell DataSafe Local Backup icon 1. on the taskbar.
Choose 2. Full System Backup to create and schedule automatic backup of all
the data in your computer.
To restore data:
Turn o your computer.1.
Disconnect all the devices connected to the computer (such as USB drive, 2.
printer, etc.) and remove any recently added internal hardware.
NOTE: Do not disconnect the monitor, keyboard, mouse, and the power
cable.
Turn on your computer.3.
When the Alienware logo appears, press <F8> several times to access the 4.
Advanced Boot Options window.
NOTE: If you wait too long and the operating system logo appears, continue
to wait until you see the Microsoft® Windows® desktop; then, shut down
your computer and try again.
Select 5. Repair Your Computer.
Select 6. Dell Factory Image Recovery and DataSafe Options and follow the
instructions on the screen.
NOTE: e restoration process might take an hour or more depending on
the size of the data to be restored.
NOTE: For more information on Dell DataSafe Local Backup, see knowledge
base article 353560 on the Dell Support website at support.dell.com.
CHAPTER 6: SYSTEM RECOVERY
52
CHAPTER 7: BASIC SPECIFICATIONS
CHAPTER 7: BASIC SPECIFICATIONS
is chapter provides the basic specications of your computer. For
more detailed specications, see the Comprehensive Specications at
support.dell.com/manuals.
CHAPTER 7: BASIC SPECIFICATIONS
53
Computer Model
Alienware M17x-R2
Dimensions
Height
51.31 mm to 53.59 mm (2.02 inches to 2.11 inches)
(Front to Back)
Width 405.89 mm (15.98 inches)
Depth 321.31 mm (12.65 inches)
Weight with 9-cell battery
5.3 kg (11.8 lb)
(starting at)
NOTE: e weight of your laptop will vary
depending on the conguration ordered and the
manufacturing variability.
Processor and System Chipset
Processor Intel® Core™ i7
Intel Core i5
System chipset Mobile Intel PM55
Memory
Connectors two internally-accessible SODIMM sockets
Capacities 2 GB and 4 GB memory modules
Memory types DDR3 1067 MHz, 1333 MHz
(dual-channel congurations)
NOTE: DDR3 1333 MHz memory is supported only
on computers with an Intel Core i7 processor.
Memory congurations
4 GB, 6 GB, and 8 GB
possible
Ports and Connectors
IEEE 1394 A one 4-pin serial connector
Network adapter one RJ45 connector 10/100/1000 Mbps
USB four 4-pin USB 2.0-compliant connectors
eSATA/USB combo one 11-pin eSATA/USB combo connector
VGA one 15-hole connector
DisplayPort one 20-pin connector
HDMI one 19-pin connector
Audio one microphone connector,
three stereo headphone/speaker connectors
CHAPTER 7: BASIC SPECIFICATIONS
54
Ports and Connectors
ExpressCard one ExpressCard/54 connector
8-in-1 Media Card Reader one combo connector
Infrared one RC6 Consumer IR port
AC Adapter
Type 240 W/150 W
NOTE: e 150 W AC adapter supports computers
with a single graphics card and a non-Extreme
Edition processor. Other congurations require
the 240 W AC adapter.
Output current
12.31 A (240 W)
(continuous)
7.7 A (150 W)
Rated output voltage 19.5 VDC
Communications
Network adapter 10/100/1000 Mbps Ethernet LAN on system
board
Wireless WLAN Mini-Card (half Mini-Card slot)•
WPAN, Bluetooth card (full Mini-Card slot)•
Drives/Cards Supported
Optical drive SATA-compliant Blu-ray Disc™ writer, Blu-ray Disc
combo, or DVD+/-RW
Hard drives two 2.5-inch drive bays supporting:
SATA-II or SATA-III hard drives•
Solid-state hard drives •
Media Card Reader card
types
Secure Digital (SD) memory card•
Secure Digital High Capacity (SDHC) card•
Secure Digital Input/Output (SDIO) card•
Multi Media Card (MMC)•
Memory Stick•
Memory Stick PRO•
xD-Picture Card (type - M and type - H)•
Hi Density-SD (SDHD)•
Video
Type up to two MXM 3.0 Type B compliant cards with
total power budget of 150 W
CHAPTER 7: BASIC SPECIFICATIONS
55
Display
Type 17.0 inch, dual-CCFL, WXGA+ (1440 x 900) •
17.0 inch, RGBLED, WUXGA (1920 x 1200) •
Keyboard (Backlit)
Layouts U.S. and Canada; Europe; Japan
Camera
Pixel 2.0 megapixel
Battery
Operating time Battery operating time varies depending on
operating conditions and can be signicantly
reduced under certain power-intensive
conditions.
Life span (approximate) 300 discharge/charge cycles
Temperature range
Operating 0° to 50°C (32° to 122°F)
Storage –20° to 60°C (–4° to 140°F)
Battery
Type 9-cell “smart” lithium ion (86 Whr)
Depth 52.3 mm (2.06 inches)
Height 41.54 mm (1.63 inches)
Width 292.7 mm (11.52 inches)
Weight 0.52 kg (1.14 lb)
Voltage 11.1 VDC
CHAPTER 7: BASIC SPECIFICATIONS
56
Coin-cell battery CR-2032
APPENDIX A: GENERAL AND ELECTRICAL
SAFETY PRECAUTIONS
Computer Setup
Read all instructions marked on the product and in the documentation •
before operating your computer.
Retain all safety and operating instructions.•
Never use this product near water or a heat source.•
Only set-up the computer on a stable work surface.•
Only operate the computer using the power source type indicated on the •
rating label.
Never block or cover any openings or fans in the computer case. ese are •
required for ventilation.
Never insert objects of any kind into the ventilation openings.•
Ensure that your computer is properly grounded when in use.•
Do not attempt to connect your computer into an outlet that is not properly •
grounded.
If an extension cord is used with your computer, ensure that the total •
ampere rating on the computer does not exceed the maximum rating on the
extension cord.
Computer Use
Route the power cable and all cables away from where people might walk or •
trip over them. Do not allow anything to rest on the power cable.
Do not spill anything on or into your computer. •
To avoid electrical shock, always disconnect all power, modem and any other •
cables from the wall outlets before handling the computer.
Electrostatic Discharge (ESD) Warning
Electrostatic Discharge (ESD) can cause damage to internal system components
if precautions are not taken. ESD is caused by static electricity and the damage
caused is usually permanent.
Computer technicians wear a special wrist-strap that grounds them to the
computer’s case to prevent ESD damage. You can reduce the chances of ESD
damage by doing the following:
Turn o your computer’s power and wait several minutes before starting to •
work.
Ground yourself by touching the case of the computer. •
Touch only those items which must be replaced. •
Avoid walking around while replacing items inside the case, especially if you •
are on a carpet or during low temperature and low humidity.
If you have to remove peripheral cards for any reason, place them on the •
portion of the computer’s case that was removed. Do not touch the edge
connectors at the bottom of the card that connect to the system board.
APPENDIX A: G ENERAL AND ELECTRICAL SAFETY PRECAUTIONS
57
General Safety Precautions
Mechanical Shock: Your computer should never be subjected to severe •
mechanical shocks. Careless handling of your computer may cause damage.
Mechanical Shock is not covered by the warranty.
Electrical Shock: If you do not open up your computer, there is nothing to •
worry about. Your computer protects itself against most irregularities in the
power source.
When You Should Contact Alienware
e battery, power cable or connector is damaged. •
Your computer has had liquid spilled into it. •
Your computer was dropped or the case was damaged. •
Normal operation of the computer does not occur when the operating •
instructions are followed.
Replacement Components or Accessories
It is only advised to use replacement parts or accessories recommended by
Alienware.
APPENDIX A: G ENERAL AND ELECTRICAL SAFETY PRECAUTIONS
58
APPENDIX B: CONTACTING ALIENWARE
NOTE: If you do not have an active Internet connection, you can nd
contact information on your purchase invoice, packing slip, bill, or Dell
product catalog.
Dell provides several online and telephone-based support and service options.
Because availability varies by country and product, some services may not be
available in your area.
To contact Dell for sales, technical support, or customer service issues:
Visit 1. www.dell.com/contactdell.
Select your country or region.2.
Select the appropriate service or support link based on your need.3.
Choose the method of contacting Dell that is convenient for you.4.
Websites
You can learn about Alienware products and services on the following websites:
www.dell.com•
www.dell.com/ap• (Asian/Pacic countries only)
www.dell.com/jp• (Japan only)
www.euro.dell.com• (Europe only)
www.dell.com/la• (Latin American and Caribbean countries)
www.dell.ca• (Canada only)
You can access Alienware Support through the following websites:
support.dell.com•
support.jp.dell.com• (Japan only)
support.euro.dell.com• (Europe only)
support.la.dell.com• (Argentina, Brazil, Chile, Mexico)
APPENDIX B: CONTACTING ALIENWARE
59
APPENDIX C: MACROVISION
PRODUCT NOTICE
is product incorporates copyright protection technology that is protected
by method claims of certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
APPENDIX C: MACROVISION PRODUCT NOTICE
60
0W3D7VA00
Printed in China.
Loading...