Dell Inspiron 7501 operation manual
Inspiron 7501
Service Manual
Regulatory Model: P102F
Regulatory Type: P102F003
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its
subsidiaries. Other trademarks may be trademarks of their respective owners.
May 2020
Rev. A00
Contents
1 Working inside your computer....................................................................................................... 6
Before working inside your computer................................................................................................................................. 6
Safety instructions.................................................................................................................................................................6
Electrostatic discharge—ESD protection.......................................................................................................................... 7
ESD field service kit ..............................................................................................................................................................7
After working inside your computer....................................................................................................................................8
2 Removing and installing components............................................................................................. 9
Recommended tools..............................................................................................................................................................9
Screw list................................................................................................................................................................................ 9
Major components of your system.................................................................................................................................... 10
Base cover............................................................................................................................................................................. 11
Removing the base cover.............................................................................................................................................. 11
Installing the base cover................................................................................................................................................ 13
Battery...................................................................................................................................................................................15
Lithium-ion battery precautions................................................................................................................................... 15
Removing the 3-cell battery......................................................................................................................................... 16
Installing the 3-cell battery............................................................................................................................................16
Removing the 6-cell battery..........................................................................................................................................17
Installing the 6-cell battery............................................................................................................................................18
WLAN card............................................................................................................................................................................19
Removing the WLAN card............................................................................................................................................ 19
Installing the WLAN card.............................................................................................................................................. 20
Memory modules..................................................................................................................................................................21
Removing the memory module (single slot)............................................................................................................... 21
Installing the memory module (single slot)................................................................................................................. 22
Solid-state drive...................................................................................................................................................................23
Removing the M.2 2280 solid-state drive (SSD-1)................................................................................................... 23
Installing the M.2 2280 solid-state drive (SSD-1)..................................................................................................... 24
Removing the M.2 2230 solid-state drive (SSD-1)...................................................................................................25
Installing the M.2 2230 solid-state drive (SSD-1)..................................................................................................... 26
Replacing the SSD-1 support bracket......................................................................................................................... 27
Removing the M.2 2280 solid-state drive (SSD-2).................................................................................................. 28
Installing the M.2 2280 solid-state drive (SSD-2).....................................................................................................29
Speakers............................................................................................................................................................................... 30
Removing the speakers................................................................................................................................................ 30
Installing the speakers....................................................................................................................................................31
GPU fan................................................................................................................................................................................ 32
Removing the GPU fan.................................................................................................................................................32
Installing the GPU fan................................................................................................................................................... 33
System fan........................................................................................................................................................................... 34
Removing the system fan.............................................................................................................................................34
Installing the system fan............................................................................................................................................... 34
Heat sink...............................................................................................................................................................................35
Contents 3
Removing the heat sink (UMA)...................................................................................................................................35
Installing the heat sink (UMA) .................................................................................................................................... 36
Removing the heat sink (discrete).............................................................................................................................. 37
Installing the heat sink (discrete)................................................................................................................................ 38
Coin-cell battery.................................................................................................................................................................. 39
Removing the coin-cell battery....................................................................................................................................39
Installing the coin-cell battery...................................................................................................................................... 40
I/O board...............................................................................................................................................................................41
Removing the I/O board................................................................................................................................................41
Installing the I/O board................................................................................................................................................. 42
Power button with fingerprint reader (optional).............................................................................................................44
Removing the power button and optional fingerprint reader.................................................................................. 44
Installing the power button with optional fingerprint reader....................................................................................45
DC-in port.............................................................................................................................................................................46
Removing the DC-in port............................................................................................................................................. 46
Installing the DC-in port................................................................................................................................................ 47
Touchpad..............................................................................................................................................................................49
Removing the touchpad............................................................................................................................................... 49
Installing the touchpad..................................................................................................................................................50
Display assembly...................................................................................................................................................................51
Removing the display assembly....................................................................................................................................51
Installing the display assembly......................................................................................................................................54
System board.......................................................................................................................................................................56
Removing the system board........................................................................................................................................ 56
Installing the system board...........................................................................................................................................57
Palm-rest and keyboard assembly.................................................................................................................................... 60
Removing the palm-rest and keyboard assembly..................................................................................................... 60
Installing the palm-rest and keyboard assembly.........................................................................................................61
3 Drivers and downloads................................................................................................................ 62
4 System setup.............................................................................................................................63
Entering BIOS setup program............................................................................................................................................63
Navigation keys....................................................................................................................................................................63
Boot Sequence.................................................................................................................................................................... 63
One time boot menu........................................................................................................................................................... 64
BIOS setup........................................................................................................................................................................... 64
Overview.........................................................................................................................................................................64
Boot configuration.........................................................................................................................................................65
Integrated Devices........................................................................................................................................................ 66
Storage........................................................................................................................................................................... 66
Display............................................................................................................................................................................. 67
Connection options........................................................................................................................................................67
Power management...................................................................................................................................................... 68
Security...........................................................................................................................................................................69
Password........................................................................................................................................................................ 70
Update and Recovery.................................................................................................................................................... 71
System management.....................................................................................................................................................72
Keyboard.........................................................................................................................................................................72
4
Contents
Pre-boot behavior..........................................................................................................................................................73
Connection options........................................................................................................................................................74
Performance...................................................................................................................................................................74
System logs.................................................................................................................................................................... 75
5 Troubleshooting......................................................................................................................... 77
Built-in self-test (BIST).......................................................................................................................................................77
System board built-in self-test (M-BIST).........................................................................................................................77
Display panel power rail built-in self-test (L-BIST)..........................................................................................................78
Display panel built-in self-test (LCD-BIST)...................................................................................................................... 78
Outcome............................................................................................................................................................................... 79
SupportAssist diagnostics.................................................................................................................................................. 79
Running the SupportAssist diagnostics............................................................................................................................ 79
System diagnostic lights..................................................................................................................................................... 79
Recovering the operating system..................................................................................................................................... 80
Flashing the BIOS.................................................................................................................................................................81
Flashing BIOS (USB key).................................................................................................................................................... 81
Backup media and recovery options..................................................................................................................................81
WiFi power cycle.................................................................................................................................................................. 81
6 Getting help and contacting Dell..................................................................................................83
Contents
5
Working inside your computer
Before working inside your computer
About this task
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start >
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION:
the network device.
5. Remove any media card and optical disc from your computer, if applicable.
To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from
Power > Shut down.
1
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.
NOTE:
Before working inside your computer, read the safety information that is shipped with your computer. For more
safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
NOTE: Disconnect your computer from all power sources before opening the computer cover or panels. After you finish
working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical
outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the pins and
the contacts.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety
instructions that is shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,
such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity which could harm internal components.
CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables have
connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When
disconnecting cables, keep them evenly-aligned to avoid bending the connector pins. When connecting cables, ensure
that the ports and the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
6 Working inside your computer
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors,
memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent
problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is
an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in
previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
• Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate
and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and
immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.
• Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures
means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the
tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may
take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.
Perform the following steps to prevent ESD damage:
• Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide
adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased
sensitivity to ESD damage.
• Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
• When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing
material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static
electricity from your body.
• Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: antistatic mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
• Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an antistatic mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system
being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESDsensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
• Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare
metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily
placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is
known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be
aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a
wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at
least once per week.
• ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a
best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the
best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have
one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to
test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.
• Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are
insulators and often highly charged.
Working inside your computer
7
• Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example,
deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a
rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work
area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is
being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as
Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically
handling any hardware components
• ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are
preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in.
The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the
new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts
should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the
ESD mat, in the system, or inside an anti-static bag.
• Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be
returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all
times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while
performing service and that they use anti-static bags for transporting sensitive components.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
8
Working inside your computer
Removing and installing components
Recommended tools
The procedures in this document may require the following tools:
• Phillips screwdriver #0
• Phillips screwdriver #1
• Plastic scribe
NOTE: The #0 screw driver is for screws M0-M1, and the #1 screw driver is for screws M2-M4.
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws,
and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type
is restored when the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when
replacing a component.
2
NOTE: Screw color may vary with the configuration ordered.
Table 1. Screw list
Component Secured to Screw type Quantity Screw image
Base cover Palm-rest and keyboard
assembly
3-cell Battery Palm-rest and keyboard
assembly
6-cell Battery Palm-rest and keyboard
assembly
Solid-state drive - 1 Palm-rest and keyboard
assembly
Solid-state drive - 2 System board M2x3 1
GPU fan System board M2x4 2
System fan System board M2x4 2
I/O board Palm-rest and keyboard
assembly
M2x4 4
M2x5 5
M2x5 8
M2x3 2
M2x3 2
Power button with
fingerprint reader
Touchpad Palm-rest and keyboard
Palm-rest and keyboard
assembly
assembly
M1.6x2.5 2
M2x2
M1.6x2
3
2
Removing and installing components 9
Component Secured to Screw type Quantity Screw image
Display-assembly hinges Palm-rest and keyboard
assembly
Power-adapter port Palm-rest and keyboard
assembly
Wireless-card bracket Palm-rest and keyboard
assembly
System board Palm-rest and keyboard
assembly
M2.5x5
M2.5x4
M1.6x2.5 1
M2x3 1
M2x3 4
2
2
Major components of your system
1. Base cover
2. Battery
3. System fan
10
Removing and installing components
4. Heat sink
5. Memory module
6. DC-in port
7. Speaker
8. System board
9. Touchpad
10. Palm-rest and keyboard assembly
11. Display assembly
12. Power button with fingerprint reader
13. Coin-cell battery
14. I/O board
15. GPU fan
16. WLAN card
17. M.2 2280 SSD
18. Solid-state drive shield
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative
for purchase options.
Base cover
Removing the base cover
Prerequisites
Follow the procedure in before working inside your computer.
About this task
The figure indicates the location of the base cover and provides a visual representation of the removal procedure.
Removing and installing components
11
12 Removing and installing components
Steps
1. Remove the seven screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.
2. Loosen the two captive screws that secure the base cover to the palm-rest and keyboard assembly.
3. Pry the base cover starting from the recess at the hinge area and work your way around.
4. Lift the base cover off away from the laptop.
Installing the base cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the base cover and provides a visual representation of the installation procedure.
Removing and installing components
13
14 Removing and installing components
Steps
1. Place the base cover on the palm-rest and keyboard assembly, and snap the base cover into place.
2. Tighten the two captive screws that secure the base cover to the palm-rest and keyboard assembly.
3. Replace the seven screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.
Next steps
Follow the procedure in after working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting
the AC adapter from the system to allow the battery to drain.
• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
Removing and installing components 15
• Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or
damage to the battery and other system components.
• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending,
or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for
assistance. See www.dell.com/contactdell.
• Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
Removing the 3-cell battery
Prerequisites
NOTE: The battery type in your computer varies depending on the configuration ordered.
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The figure indicates the location of the battery and provides a visual representation of the removal procedure.
Steps
1. Disconnect the battery cable from the system board.
2. Remove the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly.
3. Lift the battery off the palm-rest and keyboard assembly.
Installing the 3-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
NOTE: The battery type in your computer varies depending on the configuration ordered.
16 Removing and installing components
About this task
The figure indicates the location of the battery and provides a visual representation of the installation procedure.
Steps
1. Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the
palmrest and keyboard assembly.
2. Install the four screws (M2x4) that secure the battery to the system board and palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Removing the 6-cell battery
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the base cover.
About this task
NOTE: The battery type in your computer varies depending on the configuration ordered.
The figure indicates the location of the 6-cell battery and provides a visual representation of the removal procedure.
Removing and installing components
17
Steps
1. Disconnect the battery cable from the system board.
2. Remove the eight screws (M2x5) that secure the battery to the palm-rest and keyboard assembly.
3. Lift the battery off the palm-rest and keyboard assembly.
Installing the 6-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
NOTE: The battery type in your computer varies depending on the configuration ordered.
The figure indicates the location of the 6-cell battery and provides a visual representation of the installation procedure.
18
Removing and installing components
Steps
1. Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the
palmrest and keyboard assembly.
2. Replace the eight screws (M2x5) to secure the battery to the system board and palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in after working inside your computer.
WLAN card
Removing the WLAN card
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the base cover.
Removing and installing components
19
About this task
The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.
Steps
1. Remove the single screw (M2x3) that secures the WLAN card bracket to the WLAN card.
2. Remove the WLAN card bracket from the WLAN card.
3. Disconnect the antenna cables from the WLAN card.
4. Slide and remove the WLAN card from the WLAN card slot.
Installing the WLAN card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the WLAN card and provides a visual representation of the installation procedure.
20
Removing and installing components
Steps
1. Align the notch on the WLAN card with the tab on the WLAN card slot and insert the WLAN card at an angle into the WLAN card slot.
2. Connect the antenna cables to the WLAN card.
3. Align and place the WLAN card bracket on the WLAN card.
4. Replace the single screw (M2x3) to secure the WLAN card bracket to the WLAN card.
Next steps
1. Install the base cover.
2. Follow the procedure in after working inside your computer.
Memory modules
Removing the memory module (single slot)
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the base cover.
About this task
The figure indicates the location of the memory module and provides a visual representation of the removal procedure.
Removing and installing components
21
Steps
1. Lift the mylar.
2. Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot until the memory module pops
up.
3. Slide and remove the memory module off the memory module slot on the system board.
Installing the memory module (single slot)
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the memory module and provides a visual representation of the installation procedure.
22
Removing and installing components
Steps
1. Lift the mylar, and align the notch on the memory module with the tab on the memory-module slot.
2. Slide the memory module firmly into the slot at an angle.
3. Press the memory module down until it clicks into place.
NOTE: If you do not hear the click, remove the memory module and reinstall it.
Next steps
1. Install the base cover.
2. Follow the procedure in after working inside your computer.
Solid-state drive
Removing the M.2 2280 solid-state drive (SSD-1)
Prerequisites
1. Follow the procedure in before working inside your computer.
Removing and installing components
23
2. Remove the base cover.
About this task
The figure indicates the location of the solid-state drive and provides a visual representation of the removal procedure of M.2 2280 SSD
from slot 1.
Steps
1. Remove the two screws (M2x3) that secures the solid-state drive module shield to the palm-rest and keyboard assembly.
2. Lift and remove the solid-state drive module shield from the solid-state drive slot.
3. Slide and remove the solid-state drive module from the solid-state drive slot.
Installing the M.2 2280 solid-state drive (SSD-1)
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the solid-state drive bracket and provides a visual representation of the bracket alignment procedure
to accommodate the M.2 2280 solid-state drive in slot 1.
24
Removing and installing components
Steps
1. Align the solid-state drive bracket to accommodate the M.2 2280 solid-state drive.
2. Slide the solid-state drive module firmly into the solid-state drive slot at an angle.
3. Place the solid-state drive module shield.
4. Replace the two screws (M2x3) that secures the solid-state drive module shield to the palm-rest and keyboard assembly.
Next steps
1. Install the base cover.
2. Follow the procedure in after working inside your computer.
Removing the M.2 2230 solid-state drive (SSD-1)
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the base cover.
NOTE: Slot 1 supports both M.2 2280 and M.2 2230 solid-state drives.
About this task
The figure indicates the location of the solid-state drive and provides a visual representation of the removal procedure of M.2 2280 SSD
from slot 1.
Removing and installing components
25
Loading...