Delfield SALD-1 Service Manual
SALD-1 & SALD-2
Service, Installation and Care Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier
of damage! Inspect all components immediately. See page 2.
Salad and Vegetable Drier
IMPORTANT INFORMATION
READ BEFORE USE
PLEASE SAVE THESE INSTRUCTIONS!
April 2011
Salad and Vegetable Drier Service and Installation Manual
Contents
Serial Number Location ..................................2
Specifications ..........................................2
Receiving And Inspecting .................................2
Operating Instructions ...................................3
Cleaning Instructions ....................................4
Wiring Diagrams........................................5
Parts Listing ...........................................6
Standard Labor Guidelines ................................6
Warranty ..............................................7
Specifications
Model Height Width Depth Inner Liner
Capacity
SALD-1
SALD-2
32.50”
(83cm)
32.50”
(83cm)
27.00”
(69cm)
27.00”
(69cm)
27.00”
(69cm)
27.00”
(69cm)
20 Gal
(77L)*
20 Gal
(77L)*
Serial Number Information
To view the serial number on the Salad Ace machine, turn the
unit upside down. The serial number is listed on the bottom on
the side opposite the motor.
Always have the serial number of your unit available when calling
for parts or service. A complete list of authorized Delfield parts
depots can be found at www.delfield.com
©2011 The Delfield Company. All other trademarks are the
property of their respective owners, and are used for illustrative
purposes only.
Inner Liner
Diameter
15.62”
(40cm)
15.62”
(40cm)
Inner Liner
Depth
16.87”
(43cm)
16.87”
(43cm)
V/Hz/Ph Amps Ship
Weight
115/60/1 2.7 85lbs/
38kg
230/50/1 1.35 85lbs/
38kg
*Inner liner can hold up to 18 heads of chopped lettuce.
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
4. Request an inspection by the shipping company of the
5. Freight carriers can supply the necessary damage forms
6. Retain all crating material until an inspection has been
damaged equipment. This should be done within 10 days
from receipt of the equipment.
upon request.
made or waived.
2
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
Operating Instructions
Salad and Vegetable Drier Service and Installation Manual
1. Position the Salad Ace over the floor drain or place a (2) two
gallon capacity container under the drain tube.
2. Secure machine into position by depressing the brake pedal
on each caster.
3. Remove the double lid slowly. DO NOT PULL OR FORCE
LID OFF IN A QUICK MOTION. Suspend the lid from the top
edge of the stainless steel tank using the bracket provided
on the lid.
4. Remove the perforated inner liner and place in sink.
5. TO PREPARE PRODUCTS: Remove the center core from
the lettuce heads; break apart, separating leaves or cut into
desired size. Fill liner with no more than 18 heads.
Do not overload inner liner. Weight in excess of 20
lbs. will cause lid and motor failure.
6. Run cold water into the sink. Turn water off when the product
level rises within three (3) inches of liner top edge. Gently stir
water through product to remove the dirt. Allow the produce
to soak 10 minutes.
7. Drain the water from the sink. Allow the liner to remain in the
sink for 30 seconds to drain out the excess water.
8. Remove the liner from the sink and place into the “Salad
Ace”. Make sure the octagon shaped recess in the liner bottom engages with the metal octagon drive casting in the tank
bottom.
9. Place the lid on the machine, making sure the inner lid seats
on the top of the inner liner.
10. Turn the machine “ON” by rotating the bottom mounted timer
clockwise. Choosing a one-to-four minute cycle. Generally, a
two-minute cycle is sufficient to drain a full load. Machine will
turn off automatically.
11. When the time cycle has ended, wait 10 seconds for inner
liner to stop rotating before removing the lid. Remove inner
liner from the machine.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
3
Loading...