Delfield Meridian MRRI1-S, Meridian MRRI2-S, Meridian MRRI1R-S, Meridian MRRI2R-S, Meridian MRRI3-S Specifications

MERIDIAN SERIES

®

Project __________________________

Item ____________________________

Quantity _________________________

CSI Section 11400

Solid Door Roll-In Refrigerators

MODELS:

 MRRI1-S Single section  MRRI2-S Two section  MRRI3-S Three section
Solid full height door Solid full height doors Solid full height doors

 MRRI1R-S Remote  MRRI2R-S Remote  MRRI3R-S Remote

STANDARD FEATURES

• Built in door locks

• Durable stainless steel doors and shroud, for lasting
good looks

• New high-density foam insulation cuts energy costs

• Big, easy grip handles are easy to find, don’t intrude
into kitchen traffic

• Attractive aluminum side panels are easy to clean and
corrosion resistant

• Heavy-duty hinges with stay open feature

• Refrigeration system is located outside the food zone,
more space for product storage

• Mini watt door heaters eliminate condensation with
minimal energy cost

• Exterior digital thermometer with high/low
temperature alarm

• Tri seal door gaskets lower energy costs with a unique
insulating design

• Aluminum interior stands up to food acids without
corroding

• Lots of interior storage space for the money

OPTIONS AND ACCESSORIES

 Stainless steel exterior sides
 Stainless steel interior
 Door and end laminate
 Stainless steel exterior back
 Digital thermometer
 TXV
 220/50/1 electrical
 Electronic control

MERIDIAN SERIES

®

SOLID DOOR ROLL-IN REFRIGERATORS

SPECIFICATIONS
Exterior: Cabinet front and shroud shall be 22-gauge

stainless steel. Exterior sides shall be aluminum.
Facing of shroud shall be easily removable without the
use of tools.

Cabinet interior shall be anodized aluminum. Bottom
& top of liner shall be die-stamped to provide
radius corners and a recessed bottom. Base shall be
fully insulated with high-density foamed in place
polyurethane.

Doors: Solid doors shall have a 22-gauge stainless
steel exterior & anodized aluminum interior liner.
Doors shall be fully insulated with high density foamed
in place polyurethane. Each door shall have two
self-closing, cam-lift style hinges. Doors shall be easily
removable without use of tools. Door gaskets shall be
magnetic snap-in style to allow simple replacement.
Door handles shall be recessed.

• Please specify right or left hand hinging at time of order.

Mechanical controls shall be located behind a removable
shroud facing.

Refrigerators Only: All components are mounted to
the exterior cabinet ceiling, outside the food zone and are
assembled as one piece and can be removed as one piece.
Environmentally friendly R404A refrigerant is used. System
has the capability of maintaining between 27˚F and 40˚F in
heavy use food service operations. Refrigerant is metered
using a highly responsive thermostatic expansion valve.
System is controlled using Delfield’s ACT-Advanced Control
Technology electronic temperature control, which provides
improved pull down times, reducing compressor cycling and
longer compressor life with lower energy consumption.

Control system uses adaptive defrost to assure evaporator

980 S. Isabella Road
Mt. Pleasant, MI 48858
www.delfield.com

Phone: [phone]
Fax: [phone]
Email: info@delfield.com

coil is free of ice and operating at optimum efficiency.
Evaporator condensate is eliminated using an energy
efficient hot gas system.

Single Voltage Models Only: Electrical connections
shall be 115 volt, 60 hertz, single phase. Self contained
models have a ten foot (3m) long electrical cord & plug
as shown on reference chart. Cord & plug shall be wired
to the junction box on top of the unit.
Dual Voltage Models Only: Electrical connections
shall be 115/208-230 volt, 60 hertz, single phase, and
must be hard-wired to the junction box located on top
of the unit.

Notes: Bottom to be reinforced with 14-gauge
channels. All units to be supplied with easily attachable
16 gauge stainless steel ramps, one per door opening.
Wiper gasket shall be provided on bottom of door for
seal to ramp.

Approval _________________

Date ____________________

Meridian Series® Solid Door Roll-In Refrigerators

34”

86.4cm

34”

86.4cm

34”

86.4cm

PLAN VIEW MRRI1-S PLAN VIEW MRRI2-S PLAN VIEW MRRI3-S

70.75”

91.5”

226.1cm

179.1cm

28.20”

71.6cm

66”

167.6cm

34”

86.4cm

ELEVATION VIEW MRRI3-SELEVATION VIEW MRRI2-SELEVATION VIEW MRRI1-S

98”

248.9cm

91.5”

226.1cm

12.14”

30.8cm

73.28”

186.1cm

END SECTION VIEW

Model #__________
CSI Section 11400

34”

86.4cm

Ramp dimensions

see below

37.68”

95.7cm

ALL MODELS

DOOR CLEARANCE DETAIL

ALL MODELS

32.25”

29.75”

75.6cm

81.92cm

MECHANICAL DETAIL

5.92”

15.04cm

RAMP DIMENSIONS

(Not to scale)

1.06”

2.69cm

29.12”
74cm

Ramp Width

3.80”

9.7cm

PERSPECTIVE VIEW

ALL MODELS

MECHANICAL DATA

CU. FT. SHELVES # of RACK UNIT BTU/HR SHIP NEMA
MODEL VOLTAGE AMPS STORAGE SQ. FT. SHELVES CAP. H.P. SYSTEM CAP WEIGHT PLUG

REFRIGERATORS
MRRI1-S 115 6.0 36.15 NA NA 1 1/3 2092 456 5-15P
MRRI2-S 115 12.0 74.72 NA NA 2 1/2 3637 676 5-15P
MRRI3-S 115/208-230 14.0 113.28 NA NA 3 3/4 6744 960 —

Remote units supplied with: Evaporator coil, solenoid valve, expansion valve and temperature control. Condensing units to be sized and supplied with others.

REMOTE CU. FT. SHELVES # of RACK UNIT BTU/HR SHIP NEMA
MODEL VOLTAGE AMPS STORAGE SQ. FT. SHELVES CAP. H.P.* SYSTEM CAP WEIGHT PLUG

REFRIGERATORS
MRRI1R-S 115 3.2 36.15 NA NA 1 1/3 — 456 —
MRRI2R-S 115 4.2 74.72 NA NA 2 1/2 — 676 —
MRRI3R-S 115 5.2 113.28 NA NA 3 3/4 — 960 —

*Recommended

980 S. Isabella Road
Mt. Pleasant, MI 48858
www.delfield.com

Phone: [phone]
Fax: [phone]
Email: info@delfield.com

Printed in the USA.
03/07
DSMRL_R