Delfa USI-281 User Manual [ru]

Steam Iron

Unit USI-281

Instruction manual

Precautionary measures

When using the iron, take the following precautions:

Read all instructions b efore u sing

1. Use the iron only for its intended use.

2. Do not immerse the iron in water or any other liquid. This may lead to electric shock.

3. When connecting and disconnecting the power control of the heating must be in minimum position.

When you unplug the iron from the mains without pulling the cord, take the plug and pull easily.

4. Do not let cord touch hot soleplate. Let iron cool completely before you remove it in place.

5. Always turn off the iron from the mains while filling his tank with water or when the water pours out

of him.

6. Never allow children to use the iron without your supervision.

7. Do not leave the iron unattended connected to the mains.

8. Do not keep working iron the up sole, this may cause burns a soleplate or steam.

9. If the iron is not working properly, unplug it and contact an authorized service center.

10. Between ironing always place the iron upright on heel. Make sure that the iron is on a firm surface.

11. When using the iron water reservoir to be closed.

12. Use the iron only on a stable surface.

13. Do not use the iron if it is leaking or there is damage to the soleplate. Regularly check the power cord

for damage. If you find damage to the appliance, contact an authorized service center.

14. In the event of damage to the power cord contact an authorized service cen te r.

15. This appliance is not intended for use by children and persons with reduced physical or mental

abilities.

16. Do not leave children unsupervised near the included iron.

17. Check that the device is ind icated on the rating plate voltage is identical with your network.

Description of the in st rument.

1. Spray nozzle 7. Thermoregulator

2. Cover of water tank 8. Power cord

3. Steam regulator 9. Handle

4. Button of sprayer 10.Water tank

5. The steam button 11. Soleplate

6. Light Indicator 12. Button Self-clean

Recommendations before the start use.

1. The first time the iron can smell the plastic. After a short period of time, it will disappear.

2. Before first use, wipe the soleplate with a soft cloth.

3. Do not allow metal objects (buckles, buttons, zippers) under the sole not to damage her.

4. Pure wool (100% wool) can be ironed steam mode. Set the steam setting to the maximum position and use

dry ironing.

Selecting the temperature

1. Refine modes ironing for clothes that you are going to iron.

2. Fabrics having any finish (applications, folds, etc.) can be ironed at the lowest temperature.

3. If the fabric contains several kinds of fibres, select the temperature for the tissue in which the canvas of the

greatest content. For example: if the fabric contains 60% polyester and 40% cotton, you should select the
temperature corresponding to polyester and to iron without steam.

4. First, you must determine the type of fabric for ironing. Since the sole is heated sufficiently quickly, so

begins to stroke better fabrics requiring a lower ironing temperature, such as woven fabrics of synthetic
fibers. Then, in the process of ironing gradually move to tissues that require a higher temperature ironing.

5. Turn the temperature regulator by comparing its value with a dash in front of it:

· position for nylon and rayon

·· position for wool, silk and mixed fabrics

··· position for cotton or linen (steaming)

Filling the water tank

1. Unplug the iron.

2. Set the mode switch steam to "off".

3. Fill the tank through the opening for pouring water.

4. After completion of the work always drain the remaining water from the tank. Do not store the iron with

remaining in the ta nk water.

Important: If you have hard water, we recommend that you use distilled or demineralized water.
Do not use solvents or perfume water.

Steam ironing

1. Fill the tank with water as described in "Filling the water tank."

2. Connect the iron to the electrical grid.

3. Steam ironing is possible only when the maximum heating temperature of the sole. Otherwise, no

formation of steam and the water can flow through the sole.

4. Wait until the indicator light turns off, it indicates that there has been a selected temperature.

5. Set the steam supply to the desired position.

6. At the end of the work and during breaks in ironing things set the iron in vertical position.

7. After completing unplug the iron, pour the remaining water in it, and put to cool.

Spray

1. The spray can be used in any position, either in dry or steam ironing, as long as the water tank is filled

with water.

2. Press the spray button for this function.

NOTE: This button has to be pressed repetitively to start this function for the first time.

Shot of steam

Shot of steam give extra steam for removing persistent wrinkles.

1. Place the temperature selector at the “m ax” position and wait until the pilot light goes out

2. Wait for a few seconds for the steam to penetrate the fibre before pressing again.

NOTE: For the best steam quality, do not use more than three successive bursts each time. Several pumping

actions are needed to start this function.
Excessive use of this feature will cause the iron to cool, ensure that the pilot light is out, before
operating the shot of steam control