4-, 5-, 6-, 7-,
8-Roller Pump
Instruction
Manual
01509-MN
GENERAL
Delavan roller pumps are available with a variety of options, such as a choice of roller numbers (4-roller, 5-roller, 6-roller, 7-roller,
8-roller), seal materials (Viton-A or Teflon), and a direction of rotation. Also, Ni-Resist and Diamond Cast pump bodies are available on
all Delavan roller pumps. Stainless steel shaft is standard on all models.
(Read carefully before installation and operation)
FEATURES:
•
Max. flow: 9.2 gpm at 2600 rpm
•
Max. fluid temperature: 140ºF/60ºC
•
Port size: 3/4” NPT
•
Shaft size: 5/8” Solid or 1/2” Hollow
•
Cast iron, Ni-Resist or Diamond Series housing
•
Pump shaft rotation: CW Standard/CCW Optional
•
Weight: 5 lbs.
•
Rollers: Ultra Rollers standard
•
Shaft Seals: Viton standard
•
Available PTO adapters
FEATURES:
•
Max. flow: 19.6 gpm at 1000 rpm
•
Max. fluid temperature: 140ºF/60ºC
•
Port size: 3/4” NPT
•
Shaft size: 5/8” Solid
•
Cast iron, Ni-Resist or Diamond Series housing
•
Pump shaft rotation: CCW (CW available)
•
Weight: 9 lbs.
•
Rollers: Ultra Rollers standard
•
Shaft Seals: Viton standard
•
Available PTO adapters
FEATURES:
•
Max. flow: 46.5 gpm at 1000 rpm
•
Max. fluid temperature: 140ºF/60ºC
•
Port size: 1” NPT
•
Shaft size: 15/16” Solid Shaft
•
Cast iron, Ni-Resist or Diamond Series housing
•
Pump shaft rotation: CCW (CW available)
•
Weight: 19 lbs.
•
Rollers: Ultra Rollers standard
•
Shaft Seals: Viton standard
•
Available PTO adapters
FEATURES:
•
Max. flow: 19.6 gpm at 1000 rpm
•
Max. fluid temperature: 140ºF/60ºC
•
Port size: 3/4” NPT
•
Shaft size: 5/8” Solid
•
Cast iron, Ni-Resist or Diamond Series housing
•
Pump shaft rotation: CCW (CW available)
•
Weight: 9 lbs.
•
Rollers: Ultra Rollers standard
•
Shaft Seals: Viton standard
•
Available PTO adapters
•
Rear Ports
4-ROLLER SIDE PORT PUMP 5-ROLLER SIDE PORT PUMP
6-ROLLER SIDE PORT PUMP 6-ROLLER BACK PORT PUMP
7-ROLLER SIDE PORT PUMP
8-ROLLER SIDE PORT PUMP
FEATURES:
•
Max. flow: 22.5 gpm at 850 rpm max.
•
Max. fluid temperature: 140ºF/60ºC
•
Port size: 3/4” NPT
•
Shaft size: 15/16” Solid
•
Cast iron, Ni-Resist or Diamond Series housing
•
Pump shaft rotation: CCW (CW available)
•
Weight: 14 lbs.
•
Rollers: Ultra Rollers standard
•
Shaft Seals: Viton standard
•
Available PTO adapters
FEATURES:
•
Max. flow: 24 gpm at 1000 rpm
•
Max. fluid temperature: 140ºF/60ºC
•
Port size: 3/4” NPT
•
Shaft size: 15/16” Solid
•
Cast iron, Ni-Resist or Diamond Series housing
•
Pump shaft rotation: CCW (CW available)
•
Weight: 14 lbs.
•
Rollers: Ultra Rollers standard
•
Shaft Seals: Viton seals standard
•
Available PTO adapters
Series 4400 Series 5500
Series 6600 Series 6601
Series 7000
Series 8800
Figure 2. Dimensional Drawings
2
1800 RPM 2200 RPM 2600 RPM
PRESSURE GPM (HP) GPM (HP) GPM (HP)
0 psig 6.5 (.12) 7.7 (.15) 9.2 (.19)
25 psig 5.4 (.24) 6.7 (.31) 8.4 (.36)
50 psig 4.7 (.35) 5.9 (.42) 7.7 (.54)
75 psig 4.0 (.43) 5.3 (.54) 7.1 (.70)
100 psig 3.5 (.50) 4.8 (.65) 6.7 (.84)
125 psig 3.0 (.55) 4.3 (.75) 6.3 (1.02)
150 psig 2.6 (.60) 3.9 (.85) 5.9 (1.17)
Flow Rates and Horsepower Requirements for
4-Roller Pump 4400 Series (44-5111)
Note:
Horsepower listed above is for electric motor drives.
For gas engine drives, follow gas engine manufacturers' rec-
ommendations. (As an estimate for gas engines, double the
horsepower requirements for electric motors listed above.)
PRESSURE 0 psi 50 psi 100 psi 150 psi 200 psi
RPM GPM (HP) GPM (HP) GPM (HP) GPM (HP) GPM (HP)
450º 20.8 (.18) 16.4 (.98) 14.4 (1.74) 11.4 (2.31) 7.5 (2.71)
540º 25.1 (.27) 20.5 (1.16) 17.8 (2.03) 15.4 (2.74) 12.2 (3.44)
650º 30.4 (.39) 25.7 (1.45) 22.6 (2.41) 20.3 (3.42) 17.3 (4.26)
750º 34.7 (.49) 30.7 (1.68) 26.6 (2.73) 24.4 (4.00) 22.0 (5.11)
850º 39.7 (.79) 35.1 (1.93) 31.0 (3.00) 28.1 (4.60) 26.2 (5.95)
1000º 46.5 (1.62) 42.5 (2.93) 38.5 (4.11) 35.1 (5.42) —
Flow Rates and Horsepower Requirements for
5-Roller Pump 5500 Series (55-5110)
Note:
To achieve rated capacity 1" suction and pressure
hose should be used.
SPEED
MODEL (RPM) 0 psig 25 psig 50 psig 100 psig 150 psig 200 psig
6-Roller
Side & Back 540 10.8 9.6 8.5 6.9 5.6 4.6
(11/16" Rollers) 1000 19.5 18.6 17.8 16.3 15.0 13.8
7-Roller
Side-Port 540 15.0 14.0 13.2 12.0 10.8 9.9
(11/16" Rollers) 750 20.0 19.2 18.4 17.2 16.1 15.2
8-Roller
Side-Port 540 13.0 12.1 11.3 10.0 8.7 7.6
(11/16" Rollers) 1000 24.0 23.2 22.4 21.0 19.8 18.7
Flow Rates in GPM for 6-7-8-Roller Pumps -
6600, 6601, 7000 and 8800 Series (66-5110,
77-5110, 88-5110)
4-ROLLER SIDE-PORT
5-ROLLER SIDE-PORT
6-ROLLER BACK-PORT
6-ROLLER SIDE-PORT 7-ROLLER AND 8-ROLLER
SIDE-PORT
3
Tractor PTO Installation
1. Secure the PTO coupling to the pump shaft by sliding the cou-
pling as far forward as possible without touching the bearing
shield and tightening the set screws down on the key of the
pump shaft. Slide coupling onto PTO shaft and secure by
pulling collar back on PTO quick coupler, sliding onto PTO
shaft and locking into place.
2. Check pump rotation. An arrow on the pump indicates proper
rotation direction.
3. To keep the pump from rotating with the shaft, set a torque arm
and short length of chain. Bolt one end of the chain to the
torque arm and secure the other to a stationary part of the trac-
tor. Be sure the chain is at a point directly above or below the
torque arm. Fastening torque chain to a point forward or back-
ward from pump center will create a bending force on pump.
Do not fasten pump rigidly to the tractor.
4. With the pump in position, connect the suction hose to the "IN"
port and the discharge hose to the "OUT" port. Make sure the
suction hose connection is tight. A loose connection will permit
air to be sucked in and the pump will not prime itself. Use at
least a 3/4" diameter hose on the suction line.
5. Use a large suction strainer with a 40 mesh minimum screen.
Either a Delavan #1700-2 suction strainer or a Delavan
#39908-2 Y type line strainer is recommended.
Engine Installation
The pump base can be mounted on a frame and aligned for either
direct-drive or belt and pulley drive. When mounting for direct-
drive, be sure pump and engine shafts are in alignment. A flex-
ible drive coupling will compensate for fractional misalignment.
When mounting for pulley drive, be sure the engine and pump
shafts are parallel. Align pulleys and keep them as close to the
shaft bearings as possible. For gasoline engine requirements,
follow engine manufacturer's recommendation.
Operation
1. With a clear suction line and open discharge line, the pump
should displace liquid within 15 seconds. A squirt of oil in the
suction side of the pump before starting will accelerate priming
action.
2. Never run the pump dry. Excessive heat will damage rollers
and seals.
3. Do not pump abrasive white wash, paints or other abrasive liq-
uids.
4. Do not use rusty supply barrels or sandy water.
5. Do not close the discharge line of the pump while it is running
unless a means of bypassing the liquid has been installed. A
simple relief or bypass valve can be easily installed in the dis-
charge side. A Delavan #37562 or #13895 pressure relief
valve is recommended.
Maintenance
1. Your Delavan pump is equipped with permanently lubricated
ball bearings. They do not require further lubrication.
2. Do not inject oil or grease into the two weep holes on the
underside of the bearing housings. These holes are to reveal
seal leakage and to prevent the solution from forcing its way
into the bearings. The holes must be kept clean.
3.
AFTER SPRAYING —
Thoroughly flush the pump with clear
water or use a solution of approximately one cup of ammonia
in 10 gallons of water. This will dissolve most residue remain-
ing in the pump. Squirt a light oil in the pump and rotate to
cover the inner surfaces with a protective film.
4.
STORAGE.
If the pump is to be out of service for several days
or stored, flush pump with clear water or use a solution of one
cup of ammonia in 10 gallons of water. Then pump a 50 per-
cent permanent antifreeze solution through the pump. Plug ports.
Caution: Do not use gasoline, kerosene, or fuel oil.
Pump Disassembly
Note: The numbers in parentheses used in the following
text are reference numbers that are found in the
exploded views.
1. With a screwdriver, remove snap ring (1). Lift out nameplate (2).
2. With a 9/16-inch wrench unscrew capscrews (3).
3. With cover plate down, cradle pump on "IN" and "OUT" ports
on fixture under an arbor press (Fig. 4). A cradle can be con-
structed of 2" x 4" lumber. Press the shaft and rotor assembly
(6) down through the pump body, bearing the seal. The shaft
and rotor assembly will remain in the end plate.
4. Lift off seal ring (4). Slide out rollers (5).
5. Check body for wear. File off any burrs that appear on rotor.
6. Make sure rollers (5) move freely in rotor slots. Replace rollers if
out-of-round, swollen or badly worn.
7. If further disassembly is required:
a. Press out shaft and rotor assembly (6) from end plate (7)
with an arbor press while supporting the end plate on a
cradle. Remove snap ring (1).
b. To remove bearing, use a small piece of brass rod and gen-
tly tap with hammer on the inner edges of the bearing. Drive
the seal out with a screwdriver and hammer. Discard seal.
Assembly
1. A repair kit including 4, 5, 6, 7 or 8 rollers, 2 seals, and a
seal ring is available (see parts list).
2. Position a new seal in seal housing with folded edge down.
Press seal down on outer edge until it "bottoms."
8. Place seal ring (4) in groove.
9. Position end plate (7) for pressing down on pump body (10),
easing the shaft carefully through the seal. Carefully line up
matching holes of pump body and end plate.
3. Position bearing (8) in bearing housing and press downward
until it "bottoms." Apply pressure to outer bearing race.
4. File off any burrs on the rotor faces and roller slots that may
have been caused by disassembly and handling.
5. Apply a light oil to shaft, end plate surface, and inside pump
body.
6. Press shaft and rotor into body, by easing the rotor shaft
through the seal; then press shaft with an arbor press while sup-
porting body bearing inner race.
7. Insert rollers (5), one in each slot.
TROUBLESHOOTING GUIDE
PROBLEM
a. Inlet line not fully immersed in tank, or low tank level.
b. Pump not properly primed.
c. Clogged inlet strainer.
1. NO PRESSURE OR NO CAPACITY
d. Suction line air leaks. Use plumber's joint compound or Teflon tape. Tighten all connections. Check hoses for cracks or pin holes.
e. Suction line blocked or hose collapsed.
f. Pump is air-bound. Check for dry tank, or "traps" in the line. Try removing one nozzle until pump starts priming.
g. Worn and leaking seals. Replace.
h. Pump turning in wrong direction. (A reverse direction pump will not wok on a tractor PTO).
10. Press pump together in an arbor press (Fig. 4), making sure the
pressing force is applied to the inner race of the ball bearing.
A sleeve with at least a 1 inch bore (that does not exceed 2
inches outside diameter) should be used.
11. Secure end plate with four capscrews (3).
12. After tightening capscrews, turn the shaft to make sure rotor is
not binding in pump. (It may be necessary to hold shaft in vise
when rotating body to check for binding.)
13. Tap shaft with a brass hammer. If this fails to center rotor, tap
the other end of the shaft lightly. The rotor should turn freely.
CAUSES AND REMEDIES
2. PUMP RUNS, BUT LOW PRESSURE AND
CAPACITY
3. PUMP PRESSURE GOOD, BUT LOW OUTPUT
THROUGH THE NOZZLES
4. EXCESSIVE NOISE OR VIBRATION
5. IMPOSSIBLE TO ROTATE SHAFT
4
a. Suction line and fittings partially blocked or too small. Hose kinked.
b. Worn rollers. Replace with new (see parts list).
c. Clogged inlet strainer.
a. Nozzle orifices too small. Install larger sizes.
b. Outlet line too small or blocked.
c. Bypass partially open. Close it.
a. Possible loose coupler...bent or damaged shaft.
b. Excessive PTO speed...1000 rpm maximum.
c. Suction line leaks or clogged strainer (See 1-d above).
d. Worn rollers. Replace with new (see parts list).
a. Improper assembly. Tap shaft with brass hammer (Refer to assembly instructions).
b. Corrosion or foreign object in pump. Disassemble and thoroughly clean all parts. Replace worn parts. See section on Maintenance.
PART QUANTITY
NO. DESCRIPTION PER KIT
48234 Roller, Polypropylene, 1/2" diameter 4
20468 Lip Seal, Fluorocarbon (Viton) 4
31350-142 Seal Ring 2
5
Delavan Models 4400C, 4400N, 4400D, 4401C, 4401N, 4401D
REF. NO. QTY. PART NO. DESCRIPTION
1 2 15070 Snap Ring
2 1 48237 Nameplate 4400C
1 48237-1 Nameplate 4400N
1 48237-2 Nameplate 4400D
3 4 48236 Cap Screw
4 1 31350-142 Seal Ring
5 4 48234 Ultra Rollers 1/2"
6 1 31661-14 Shaft & Rotor Assy. Cast Iron
1 31661-14 Shaft & Rotor Assy. Ni-Resist
1 31661-17 Shaft & Rotor Assy. Diamond
1 31661-18 Hollow Shaft & Rotor Assy.
Cast Iron
1 31661-18 Hollow Shaft & Rotor Assy.
Ni-Resist
1 31661-23 Hollow Shaft & Rotor Assy.
Diamond
7 1 46231-1 Endplate Cast Iron
1 46231-2 Endplate Ni-Resist
1 46231-3 Endplate Diamond
8 2 15072 Bearing STD#6203ZZ
9 2 20468 Lip Seal Viton
10 1 48229-1 Pump Body Cast Iron
1 48229-2 Pump Body Ni-Resist
1 48229-3 Pump Body Diamond
Universal Repair Kit
44-4000 RK
4-Roller Pump Repair Kit for 4400 Pump
Note:
Repairs 44-XXXX
Delavan Models 5500C, 5500N, 5500D
REF. NO. QTY. PART NO. DESCRIPTION
1 2 15334 Snap Ring
2 1 48255 Nameplate 5500C
1 48255-1 Nameplate 5500N
1 48255-2 Nameplate 5500D
3 4 15341 Cap Screw
4 1 48252 Seal Ring
5 5 48253 Ultra Rollers 1"
6 1 31661-15 Shaft & Rotor Assy. Cast Iron
1 31661-15 Shaft & Rotor Assy. Ni-Resist
1 31661-20 Shaft & Rotor Assy. Diamond
7 1 48248-1 Endplate Cast Iron
1 48248-2 Endplate Ni-Resist
1 48248-3 Endplate Diamond
8 2 16228 Bearing STD#6705ZZ
9 2 47927 Lip Seal Viton
10 1 48246-1 Pump Body Cast Iron
1 48246-2 Pump Body Ni-Resist
1 48246-3 Pump Body Diamond
PART QUANTITY
NO. DESCRIPTION PER KIT
48253 Ultra Roller, 1” Diameter 5
47927 Lip Seal, Viton 2
48252 Seal Ring 2
Universal Repair Kit
55-1700 RK
5-Roller Pump Repair Kit for 5500 Pump
Note:
Repairs 55-XXXX
6
Delavan Models 6600C, 6600N, 6600D, 6601C, 6601N, 6601D
REF. NO. QTY. PART NO. DESCRIPTION
1 2 15070 Snap Ring
2 1 46210-2 Nameplate 6600C
1 46210-7 Nameplate 6600N
1 46210-3 Nameplate 6600D
1 46210-1 Nameplate 6601C
1 46210-8 Nameplate 6601N
1 46210-9 Nameplate 6601D
3 4 15077 Capscrew
4 1 24819 Seal Ring
5 6 19341 Ultra Rollers 11/16"
6 1 31661-8 Shaft & Rotor
(Cast Iron/Ni-Resist)
1 31661-9 Shaft & Rotor (Diamond)
7 1 31664-1 End Plate Cast Iron
1 31664-2 End Plate Ni-Resist
1 31664-3 End Plate Diamond
8 2 15072 Bearing (STD#6203ZZ)
9 2 20468 Lip Seal Viton
10 1 50073-1 Pump Body Cast Iron Side
1 50073-2 Pump Body Ni-Resist Side
1 50073-3 Pump Body Diamond Side
1 24817-1 Pump Body Cast Iron Rear
1 24817-2 Pump Body Ni-Resist Rear
1 24817-3 Pump Body Diamond Rear
PART QUANTITY
NO. DESCRIPTION PER KIT
19341 Ultra Roller 11/16” Diameter 6
20468 Lip Seal, Viton 4
24819 Seal Ring 2
Universal Repair Kit
66-6500 RK
6-Roller Pump Repair Kit for 6600 & 6601 Pumps
Note:
Repairs 66-XXXX
7
Delavan Models 7000C, 7000N, 7000D
8
REF. NO. QTY. PART NO. DESCRIPTION
1 2 15334 Snap Ring
2 1 46209-3 Nameplate 7000C
1 46209-4 Nameplate 7000N
1 46209-7 Nameplate 7000D
3 4 15341 Capscrew
4 1 24829 Seal Ring
5 7 19341 Ultra Rollers, 11/16"
6 1 31661-10 Shaft & Rotor Assy.
(Cast Iron /Ni-Resist)
1 31661-11 Shaft & Rotor Assy. Diamond
7 1 31666-1 End Plate Cast Iron
1 31666-2 End Plate Ni-Resist
1 31666-3 End Plate Diamond
8 2 16228 Bearing (STD#6205ZZ)
9 2 47927 Lip Seal Viton
10 1 24842-1 Pump Body Cast Iron
1 24842-2 Pump Body Ni-Resist
1 24842-3 Pump Body Diamond
PART QUANTITY
NO. DESCRIPTION PER KIT
19341 Ultra Roller 11/16” Diameter 7
47927 Lip Seal, Viton 2
24829 Seal Ring 2
Universal Repair Kit
70-7700 RK
Pump Repair Kits
Note:
Repairs 77-XXXX
Delavan Models 8800C, 8800N, 8800D
REF. NO. QTY. PART NO. DESCRIPTION
1 2 15334 Snap Ring
2 1 46209-1 Nameplate 8800C
1 46209-2 Nameplate 8800N
1 46209-6 Nameplate 8800D
3 4 15341 Capscrew
4 1 24829 Seal Ring
5 8 19341 Ultra Rollers, 11/16"
6 1 31661-12 Shaft & Rotor Assy
(Cast Iron /Ni-Resist)
1 31661-24 Shaft & Rotor Assy Diamond
7 1 31666-1 End Plate Cast Iron
1 31666-2 End Plate Ni-Resist
1 31666-3 End Plate Diamond
8 2 16228 Bearing (STD#6205ZZ)
9 2 47927 Lip Seal Viton
10 1 24842-3 Pump Body Cast Iron
1 24842-4 Pump Body Ni-Resist
1 24842-6 Pump Body Diamond
PART QUANTITY
NO. DESCRIPTION PER KIT
19341 Ultra Roller 11/16” Diameter 8
47927 Lip Seal, Viton 2
24829 Seal Ring 2
Universal Repair Kit
88-7560 RK
Pump Repair Kits
Note:
Repairs 88-XXXX
9
ROLLER PUMP COUPLERS
PICTURE PART # FITS PUMPS RPM PUMP SHAFT SIZE PTO SHAFT DESCRIPTION
46814-1 6600 Series 1000 5/8” Dual Speed
7/8” shaft 1 3/8” Dual Speed 540 & 1000 RPM,
Old Style & 540 & Corrosion Resistant,
46814-2 Competitive Pumps 1000 7/8” Dual Speed Cast Aluminum, Nylon Collar
7- and 8-Roller Pumps 540 & 1 3/8”
46814-3 7000 & 8800 Series 1000 15/16” Dual Speed
5500, 8800, & 7000* 540 RPM, Forged Steel Body
35735 Series (540 only) 540 15/16” 1 3/8” Nylon Collar
540 & 1 3/8”
35979 Pumps, Turbo 90 1000 15/16” 1 3/8” Nylon Collar, 1 3/4” PTO
35992 Pumps, Turbo 90 1000 15/16” 1 3/4” Nylon Collar, 1 3/4” PTO
46935-1 Pumps, Turbo 90 1000 15/16” 1 3/8”
46647 Pumps, Turbo 90 1000 15/16” 1 3/4”
50101 4400 Series 2600 5/8” 5/8” Mild Steel Set Screw Coupler
*7000 Series Roller Pump Use on 540 RPM PTO Only
**Collar Coupler reduces possible vibration by clamping a full 360 degrees on the pump shaft & PTO. This better centers the pump shaft to the trac-
tor PTO, giving less chance of uneven wear. Both ends of the Coupler must be wrench-tightened onto the PTO & Pump shafts before operation.
NOTE: Do not force Coupler too far onto the PTO. After Coupler is in position, 1/4” - 3/8” of PTO should be visible.
***Do not use series 46814 Couplers for 5-Roller or Turbo 90 Pumps.
5500 & 8800Roller 1000 RPM, Forged Steel Body
5500 & 8800Roller 1000 RPM, Forged Steel Body
5500 & 8800 Roller
*Collar Coupler (see below)
1 3/4 1000 RPM PTO,
5500 & 8800 Roller
UNIVERSAL REPAIR KITS
REPAIR FOLLOWING PUMP
NEW REPAIR KIT OLD REPAIR KIT DELAVAN OLD # DELAVAN NEW # HYPRO # DESCRIPTION
44-4000RK 48631-1 44-Cast Iron 4400 4001/4101 4 Ultra Rollers
66-6500RK 48394-1 6/66-Cast Iron 6600 6500 6 Ultra Rollers
70-7700RK 48394-2 77-Cast Iron 7000 7700 7 Ultra Rollers
88-7560RK 48394-3 88-Cast Iron 8800 7560 8 Ultra Rollers
55-1700RK 48632-1 55-Cast Iron 5500 1700 5 Ultra Rollers
10
Ni resist 4 Viton Shaft Seals
Diamond 2 Universal O-Rings
Ni resist 4 Viton Shaft Seals
Diamond 2 Universal O-Rings
Ni resist 2 Viton Shaft Seals
Diamond 2 Universal O-Rings
Ni resist 2 Viton Shaft Seals
Diamond 2 Universal O-Rings
Ni resist 2 Viton Shaft Seals
Diamond 2 Universal O-Rings
11
NOTES
Returns
Delavan Products Warranty
All products sold by Delavan are warranted only to purchasers from
Delavan for resale or for use in purchasers' own business or original
equipment manufacture, against defects in workmanship or materials
under normal use, maintenance and service (rental use excluded), if
notice of said defect is received by Delavan at the factory within 90
days after installation or one year from date of shipment from the
factory, whichever first occurs. The sole and exclusive obligation of
Delavan under this or any implied warranty shall be to replace or,
at its option, to repair, without charge, any product which is deter-
mined by Delavan to be defective in workmanship or materials after
the product is returned to the Delavan factory, shipping costs pre-
paid. In no event shall Delavan be liable to any person for indirect
or consequential damages or for injury or commercial loss resulting
from any use or inability to use and Delavan product. Delavan
expressly negates any other warranty, express or implied, including
any warranty of merchantability or fitness for a particular purpose,
or arising from any course of dealing or custom or usage of trade.
No person, including any dealer or representative of Delavan, is
authorized to make any representation or warranty on behalf of
Delavan in addition to or inconsistent with these provisions.
Purchasers to whom these provisions apply agree to hold Delavan
harmless from claims by their customers in excess of the obligations
of Delavan expressly set forth herein.
Important:
Whether you are returning your pump for warranty or for repair,
you must do the following:
1. Flush chemical residue from the pump (best done in the field).
2. Tag pump with type of chemicals having been sprayed.
3. Include complete description of operation problem, such as
how pump was used, symptoms of malfunction, etc.
Since pumps can contain residues of toxic chemicals these steps are
necessary to protect all the people who handle return shipments,
and to help pinpoint the reason for the breakdown.
All Delavan products are warranted against manufacturing defects
(see warranty, below). In the event you feel you have a warranty-
covered, returnable item, return the pump to your dealer, who will
replace a warrantable pump for you. Delavan's "No Hassle
Warranty" puts you back in the field sooner!
1228 Chestnut Avenue • Minneapolis, MN 55403
Toll Free: 1-866-DELAVAN (335-2826)
(612) 333-3189
Toll Free Fax: 1-888-726-5906
(612) 333-3231
Loading...