Dekolink Wireless DBDAPS950W90 Spec sheet

HIGH POWER CHANNEL SELECTIVE

SMR/iDEN/TDMA REPEATER

MAIN FEATURES

• 50 Watt 1dB Output Power

• 10 Watt Downlink Composite Power

• 90 dB RF Gain

• Flexible Software Controlled Filter

Array

• 1 to 8 Programmable Filters, 1 to 8 Channels each Filter

• Separate Programmable Bandwidth for each Channel

• High Spectral Purity

• Small Dimensions

• Exceptionally linear operation

• Computer (Laptop) Control and

monitor

• Output Power & Fault Monitor

• Special Tailoring Capability to meet

Specific Customer Requirements

• Patent Pending

Dekolink’s new Digital Channel Selective Repeater employs advanced Digital Signal Processing technology (DSP) that provides significant advantages over conventional repeaters. This innovative system introduces new system capabilities, which enable a wide variety of applications particularly when adjacent channel selectivity and very high spectral purity and selectivity is required.

The Digital Channel Selective Repeater generates a flexible array of 8 DSP based software controlled independent variable bandwidth channels across the whole 800 MHz SMR band. Each channel parameters such as central frequency, bandwidth, and filter slopes, are all software controlled in a local mode and can be remotely controlled via a wireless modem.

The 800 MHz SMR band is crowded with many different services. Services such as IDEN, LMR, SMR and Public Safety are interfering with each other in the same geographical area making it often impossible to support these services simultaneously.

The Digital Channel Selective Repeater provides a very efficient solution to the 800MHz interference problem by enabling high spectral selectivity while maintaining a clear low noise spectrum. The Digital Channel Selective Repeater has a built-in software controlled frequency shift capability making this product ideal for those applications where frequency shifting is required and particularly in sites where high gain is required under poor antenna isolation conditions.

Dekolink’s Digital Channel Selective Repeater provides a 40dbm composite output power, ideal for outdoor applications. Dekolink also provides a cost effective medium power system providing the same features and capabilities but with 32 dBm composite power. These amplifiers are an excellent choice for in-building coverage applications when frequency selectivity is required.

Dekolink Wireless Proprietary and Confidential Information. Copying, Distribution, and Disclosure are prohibited without Express Authorization from Dekolink Wireless Company.

Dekolink Wireless

Tel: 972-3-9180-180

, Fax: 972-3- 190-9180

This document is protected by all applicable copyright laws.

; 16 Bazel St.Qiryat-Arieh; Petah-Tikva; Israel, 49510

;

e-mail:marketing@dekolink.com, web:www.dekolink.com

Electrical Specification

Downlink Up link

Frequency Range

Pass band Gain @Min attenuation. 90 dB typical

Filters Bandwidth 12.5 –250 KHz (Programmable)

Delay 20-80 µSec. Depending on filter Bandwidth

Channel Setting Resolution 0.5 kHz

Passband Ripple ± 2.5 dB max

Channel Ripple ± 0.5 dB max

Delay Variation ± 250 nSec max

Noise Figure @max gain 5.0 dB

3rd Order Output Intercept Point +62 dBm typical +50 dBm typical

IMD @ 4 tone 48 dBc typical

IMD @ 8 tone 45 dBc typical

Power Output @1 dB Gain Compression 50 Watt 10 Watt

Composite Output Power +40dBm +30 dBm

Automatic Gain Control (user enable) 15 dB attenuation Range

Impedance Level 50 ohms

V.S.W.R In/Out 1.5: 1 max

Spurious Outputs 55 dBc max

Power Supply 90 to 260 VAC

Manual Gain Control 30 dB @2 dB/step

Size 60x40x30 cm (23.6x15.7x12 inch)

RF Connectors N-type Female

Weight 42 kg. (95 lb)

Operating temperature - 30°C to + 50°C

* specifications are subject to change without notice

See table below

and required slope.

48 dBc typical

@ 33dbm/tone

@ 23 dbm/tone

45 dBc typical

@ 30dbm/tone

@ 20 dbm/tone

System Frequency range:

SYSTEM TYPE

iDEN / SMR / LMR 800 851-866

iDEN / SMR 900

Public-safety

NPSPEC

2 Way Paging