Deister Electronic PRM5M User Manual

Wiring and Installation Instructions PRM 5

PRM 5

Wiring and

Installation Instructions

V 1.0 12/00

03.01.01 © ‘2000 deister electronic GmbH Page 1/15

Wiring and Installation Instructions PRM 5

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to user:

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of deister electronic GmbH.

deister electronic GmbH reserves the right to make changes to any and all parts of this documentation without obligation to notify any person or entity of such changes.

December 2000

deister electronic GmbH Hermann-Bahlsen-Str. 11 - 13 D-30890 Barsinghausen

Phone: (+49) (0) (51 05) 5 16-01 Fax: (+49) (0) (51 05) 5 16-2 17 E-Mail: info@deister-electronic.de

03.01.01 © ‘2000 deister electronic GmbH Page 2/15

Wiring and Installation Instructions PRM 5

Contents

1 Technical Data 2 Wiring Diagram

2.1 PRM 5 Wiegand 2-wire

2.2 PRM 5 Magstripe Emulation

2.3 PRM 5 RS 232

2.4 PRM 5 RS 485

2.5 Supervised F2F

3 Mechanical Dimensions

3.1 PRM 5 Reader

3.2 Surface Spacer AP5

3.3 Flush Mounting Bezel FM5

4 Communications Protocol

4.1 Wiegand Standard

4.2 Data/Clock

4.3 Magstripe Emulation

4.3.1 Magstripe Interface according to ISO 7811/2-1995 - Track 2

4.4 Protocol for PRM 5 with RS 232/RS 485 Interface (no Partyline protocol)

5 Installation

5.1 PRM 5 Reader

6 Interface

6.1 Indicators

6.2 Magstripe Emulation

6.3 Wiegand/Data/Clock

7 Appendix

7.1 Supervised F2F

03.01.01 © ‘2000 deister electronic GmbH Page 3/15

Wiring and Installation Instructions PRM 5

1 Technical Data

Mounting: 1. Flush mounting in non-metallic surfaces

2. Surface mounting using an AP5 spacer

3. Mounting on single-gang electrical box using fixing plate FM 5

Material: ASA plastic housing; polyurethane encapsulated electronics

Housing dimensions: 80 x 80 x 16 mm

Temperature range: -25...+70 °C

Power supply: 8...30 V DC <100 mA

Electrical protection: Reverse polarity diode protection on power lines;

high-speed transient voltage suppressor diodes on data lines

Protection type: IP 65 (IEC 529)

Frequency: 13.56 MHz

Approvals: CE, EN 300 330 (European post)

Reading distance: Up to 3 cm (depending on installation and transponder type)

Data output mode: 1. One transmission per activity

2. Cyclical transmission

Interface: 1. Wiegand 2-wire (open collector)

2. Data/Clock (open collector)

3. Magstripe emulation (open collector)

4. RS 232

5. RS 485

6. F2F Supervised

Electrical connection: 12 position plug-in strip connector with screw terminals

Beeper: External control

Red LED: External control

Green LED: External control

Yellow LED: Indicates power to the reader

Wiring and Installation Instructions PRM 5

2 Wiring Diagram

Rear view of the reader

2.1 PRM 5 Wiegand 2-wire

2.2 PRM 5 Magstripe Emulation

+ 10 hidden pages