DEI Headquarters NAH5603, NAH4420 User Manual
T W O - W A Y 6 - B U T T O N L C D A U T O M A T I C / M A N U A L
T R A N S M I S S I O N R E M O T E S T A R T E R
AS-3472TW-FM
User Guide
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device m ust accept any interference received, including interference
that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
It is the responsibility of the vehicle operator to ensure their vehicle
is parked in a safe and responsible manner.
1. a) Manual transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in the NEUTRAL
position and the parking brake is engaged in order to avoid accidents
upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in “Park” in order to
avoid accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled
or put into valet mode before servicing.
WARNING
DOC: 1.00 - AS-3472TW-FM - - June 25, 2008 - - MO - Assembled in Canada
Table of Contents
Introduction ............................................................ 2
Using the Transmitter............................................ 3
LCD Remote Functions ...................................... 3
Vehicle Presets....................................................... 7
Heater & Heated Seat......................................... 7
Windshield Wipers, Radio & Headlights............. 7
Arming the Starter Kill........................................... 7
Remote-Starting Your Vehicle.............................. 8
Setting Your Vehicle Into Ready Mode............... 8
Remote-starting .................................................. 8
Driving Off ........................................................... 9
Remote Starter Features ....................................... 9
Idle Mode ............................................................ 9
Valet Mode.......................................................... 9
Panic Mode....................................................... 11
Quick LockoutTM................................................ 11
Cold Weather Mode.......................................... 11
The Starter Kill and the Anti-grind Feature....... 12
Extended Run Time.......................................... 12
Advanced Features: Installation-programmable
Options.................................................................. 12
Passive or Active Arming of the Starter Kill...... 12
OEM-Style Alarm .............................................. 12
Remote Door Locks.......................................... 13
Priority Door Access ......................................... 13
Ignition-Controlled Door Locks ......................... 13
Ignition Relock .................................................. 13
Secure Lock...................................................... 13
Remote Trunk Release..................................... 13
Safe Start .......................................................... 13
Installer-programmable Valet Mode ................. 14
“Home ValetTM” Mode ..................................14
Turbo Mode....................................................... 14
Engine Run Time .............................................. 14
How to Access to Runtime Status (Indication
purpose only)...............................................15
Temperature Request (If ACC-Temp-101
installed)............................................................ 15
Constant While Pressed ...................................15
Horn Chirp Timing............................................. 15
Multi-car Operation ........................................... 15
LCD Transmitter Operation and Confirmations
(Second Car Control)........................................... 16
Basic Operations............................................... 16
Start/Stop While in Safe Start Mode................. 16
Missing a Start or a Stop Confirmation............. 17
Multi-Level Features (default state) ................... 17
Accessing the Multi-Level Features and Other
Transmitter Functions....................................... 18
Troubleshooting Transmitting Range................ 19
LIMITED LIFETIME WARRANTY......................... 20
Introduction
This is a state-of-the-art remote car starter system. The system is packed with advanced features
such as priority access to the driver’s door (commodity features) and the Safe Start children safety
feature.
With many advanced functions, this product will satisfy any one of your expectations from high-end
commodity and security systems, without neglecting any standard feature commonly offered by
entry-level starters.
P. 2 User Guide
Using the Transmitter
START/STOP Button:
UNLOCK Button:
disarms the Starter Kill
Function Button (F):
LOCK Button:
arms the Starter Kill
TRUNK Button:
AUX (if programmed):
CWM
Your remote starter is equipped with a 5-button multi-channel remote control. It can operate two
independent vehicles equipped with identical remote starters (see Multi-car operation section,
later in this Guide, for second-car transmitter functions).
LCD Remote Functions
The transmitter offers several command-confirmation and timer features. This section explains
some of the key functions available. The next section gives a summary of the button combinations
used to access the functions.
Note: If you wish to exit a function while still in the process of accessing it, simply stop and wait at
least 5 seconds: the transmitter will return to its normal state.
The functions of the transmitter are as follows:
Locks all Doors and
• AUX 2 output
• Stop
• Temperature request
• Panic
•
Activates the Trunk
output (AUX 3)
F button Functionality:
(By default)
button
1x Level 1 L – 01 Enables backlight
2x Level 2 L – 02 Enables backlight
3x Level 3 L – 03 Enables backlight
4x Enters programming mode MENU Enables backlight
Note: The order of
Backlight:
Press and hold the button (for more than 3 seconds and less than 5 seconds), to turn the
ON
Backlight
for 3 seconds. If the button is pressed down for more than 5 seconds, the
backlight will stay ON until the button is released. A quick way to access the backlight is to press
the button quickly (for less than 1 second): the backlight will turn ON 3 seconds.
. Turns On the backlight
. For accessing Multi-level functions and Menu
Press
Less than 3 seconds
LEVELS
and
MENU
can be re-arranged in the menu option
LCD display
Unlocks all Doors and
Starts or Stops the engine
(Normal functions)
Press
more than 3 seconds
FBPRO
.
User Guide P. 3
Button
Press for < 1 second Backlight ON for 3 sec.
Press for > 3 seconds and < 5 seconds Backlight ON for 3 sec.
Press for > 5 seconds
Backlight will stay ON until button is released.
Backlight
Selecting and adjusting Menu options:
When in
MENU
, press button to enter the menu.
Press button to move up in the menu or button to move down in the menu.
Press button to select the option you would like to adjust.
Press button to increase the value, activate or deactivate a function or toggle through the
selection.
Press button to decrease the value, activate or deactivate a function or toggle through the
selection.
Press button to move to the next sub-option or go back to the main menu.
Order Menu Option LCD display Function
1 Parking Menu PARK
Parking hour
Parking minute
2 Alarm Clock Menu ALARM
Alarm hour
Alarm minute
Toggle alarm
3 CWM Menu CWM Cold Weather Mode
Toggle CWM mode
4 VALET Menu VALET
Toggle valet mode
5 Time Start Menu TSTAR
Time start hour
Time start minute
Toggle time start
6 SECURE Menu SECUR Lock the transmitter keypad
Toggle lock remote
7 Backlight Color Menu COLOR
Backlight There are 8 different Blue lights is default
Toggle Parking
countdown
P 0:00
0 is flashing
P 0:30
30 is flashing
P -- ON
Or
P – OFF
A 12:00
12 is flashing
A 12:00
00 is flashing.
A -- ON
Or
A – OFF
ON
Or
OFF
ON
Or
OFF
T 12:00
12 is flashing.
T 12:00
00 is flashing
T -- ON
Or
T – OFF
PRESF
when remote is locked.
Adjust parking hour(s)
(value from 0 to 2)
Adjust parking minute(s)
(value from 0 to 59)
Enable or disable parking countdown
There is a beep 5 min. before the
parking countdown reaches 0.
Adjust alarm hour(s)
(value from 0 to 12)
Adjust alarm minute(s)
(value from 0 to 59)
Enable or disable alarm
Adjust time start hour(s)
(value from 0 to 12)
Adjust time start minute(s)
(value from 0 to 59)
Enable or disable
Selecting PRESF will unlock the
transmitter keypad
P. 4 User Guide
8 LCD On Menu LCD
LCD on time
9 Clock Menu CLOCK
Clock hour
Clock minute
10 Temperature Menu TEMP
Temperature
11 Language Menu LANGU
Language
12 Side button Menu SBPRO Side Button Programming
13
FB programming
F Button Function
Menu
colors
OFF 01
OFF 15
OFF 30
OFF 60
ON
12:00
12 is flashing.
12:00
00 is flashing.
CTEMP
Or
FTEMP
ENG
Or
FRAN
PANIC
STOP
TEMP
AUX 2
CWM
FBPRO F Button Programming
1 2 3 M
2 3 1 M
2 1 3 M
3 1 2 M
M 1 2 3
1 min., 15 min., 30 min., 60 min. and
Deg Celsius or Fahrenheit
AUX 2 output, Stop, Temperature
request, Panic, CWM ( Cold weather
ON
1 min. is default.
Adjust clock hour(s)
(value from 0 to 12)
Adjust clock minute(s)
(value from 0 to 59)
Deg. Celsius is default
English is default
mode)
Parking Countdown:
This version of the countdown feature is particularly useful for keeping track of parking meter time:
the user may quickly set up the countdown using the
5 minutes before the Parking countdown reaches 0.
Parking Menu
. The transmitter will beep once,
Alarm Clock:
The LCD remote control has a built-in alarm clock, which can be set up using the
Menu
. Once the programmed time is reached, the remote will beep 6 times every minute until a
button is pressed.
Alarm Clock
CWM menu:
When this feature is enabled, press for 3 seconds to enter or exit Cold Weather mode. If
disabled, press then button to enter or exit Cold Weather mode.
Valet menu:
When this feature is enabled, press to enter Valet mode. When this feature is disabled, press
+ buttons simultaneously.
Time start menu:
This feature is used to remote start the car at a pre-programmed time. Once the pre-programmed
time is reached, the remote will send a start command to the car module.
User Guide
P. 5
Secure Remote feature:
car
This feature is used to lock the keypad of the transmitter to avoid accidental button press. When
the remote is locked and a button is pressed, the LCD displays “
PRESF
” for 1 second, then goes
back to the clock.
The transmitter keypad can also be locked as follows:
• Press to go to Menu.
• Within 3 seconds, press .
• Press for about 1 second to unlock the transmitter keypad.
LCD ON menu:
If there is no activity within the programmed time, the LCD will turn off. This feature maximizes the
lifetime of the battery.
Clock Menu:
The Clock menu is used to set the current time on your remote control.
Side button Menu:
The side button can be programmed as one of the following buttons:
• Panic button;
• Stop button;
• Temperature request button;
• AUX 2 output button;
• or CWM.
F Button Function Menu:
The order of
LEVELS
and
MENU
can be re-arranged using the F Button Function Menu.
Button Operation:
Button LCD Beep(s)
Lock button
Unlock button
Trunk button TRUNK text for 1s 1 beep
Start button START text for 1s 1 beep
Engine running
Run time + icon + Blue backlight for 3s
Engine stop Red backlight on for 3s 2 beeps
Unlock+Start button Valet icon if pressed more than 3s 1 beep
Lock+Unlock button 1 beep
Trunk+Lock button
(2nd car operation)
Trunk+Unlock button
(2nd car operation)
Trunk+Start button
(2nd car operation)
L --01 → Lock button
L --01 → Unlock button
L --01 → Trunk button
L --01 → Start button
(pressed more than 3s)
L --02 → Lock button
(2nd car unlock)
L --02 → Unlock button (2nd
car unlock)
L --02 → Trunk button(2
nd
Lock
icon + LOCK 1 beep
Unlock
icon + ULOCK 2 beeps
3 beeps
Lock icon + LOCK 1 beep
Unlock icon + ULOCK 2 beeps
START text for 1s 1 beep
1 beep
1 beep
Temperature
CWM or MTF text for 1s 1 beep
LOCK and Lock icon 1 beep
ULOCK and Unlock icon 2 beeps
TRUNK text for 1s 1 beep
P. 6 User Guide
Loading...