DEI Headquarters DS4WS User Manual

DS4WS

WIRELESS BLUETOOTH SIREN
SECURITY ACCESSORY

510-10652 (1.00) PAGE-1

A. Product Description:

The DS4WS wireless Bluetooth Siren security kit is specifically design to work with Directed’s DS4 and DS4+ product

line up. The product enables a seamless wireless data transmission between the DS4 or DS4+ Digital remote starter
without the need of running physical wires between the engine compartment and the passenger cabin.

B. MOUNTING THE DS4WS

 The DS4WS should be installed in the engine compartment where it should not obstruct with any moving

parts.

 Select a location where you can install the mounting bracket to a metal using a self-tapping screw.
 Install the power and ground wires then follow the DS4WS pairing procedure.

C. PAIRING DS4WS TO A DS4/DS4+ SYSTEM

In order for the DS4WS and DS4/DS4+ system to start communicating, the installer must PAIR the DS4WS to the
DS4/DS4+. PAIRING procedure must be completed successfully to enable both system to recognize each other and
authenticate the communication.

Pairing DS4WS to DS4/DS4+ system.

1. Make sure that DS4/DS4+ system has been fully configured and flashed prior to step2.

2. Put the DS4/DS4+ system in pairing mode by;
a. Press and release, press and hold the antenna programming button until the LED start to flash.
b. Release the programming button

3. Put the DS4WS into paring mode by;
a. Press and release, press and hold the programming button until button’s LED starts to flash.
b. Release the programming button.

4. The DS4WS wireless siren will sound to confirm successful pairing.

5. Pair the remote by following the normal remote pairing procedure from DS4/DS4+ installation guide.

D. USING DS4WS

DS4WS will sound the siren according to the command received and according to how the sound was configured
(siren mode or voice mode).

DS4WS

WIRELESS BLUETOOTH SIREN
SECURITY ACCESSORY

510-10652 (1.00) PAGE-2

GOVERNMENT REGULATIONS

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesirable operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can be
determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of
the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.

To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm
or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance.
WARNING! : Changes or modifications not expressly approved by Directed Inc. could void user's authority to operate the
equipment.

This device complies with Industry Canada licence-exempt RSS-247 standards. Operation is subject to the following two
conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standards RSS-247. Son fonctionnement est soumis aux deux
conditions suivantes:

1. Cet appareil ne doit pas provoquer d'interférences et

2. Cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de

l'appareil.”

Health Canada RF Exposure Warning:

This device complies with Health Canada’s Safety Code. The installer of this device should ensure that RF radiation is not emitted
in excess of the Heath Canada’s requirement. The device must maintain a separation distance of 20cm or more from the person’s

body, except for the hands and wrists. Information can be obtained at:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-eng.php

Lignes Directrices de Santé Canada sur l’exposition aux radiofréquences:

Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d’installation de cet appareil doit s’assurer que
les rayonnements RF n’est pas émis au-delà des limites établies par Santé Canada. L’emplacement de l'appareil doit se situer à
une distance de 20cm ou plus par rapport au corps de la personne, à l’exception des mains et des poignets. Les informations
peuvent être obtenues à l’adresse Internet suivante:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-fra.php