DEI Headquarters DEIBLE1 Users manual

INSTALLATION GUIDE

HK2

DS4+

This product is intended for installation by a professional installer only! Attempts to ins tall this product by a person other than a trained profes sional may result in severe electrical system and components.

2016-10-20

damage to a vehicle’s

Contents

Warning! Safety first ....................................................................................................................... 3

Introduction .................................................................................................................................... 4

Pre-installation and application warnings ..................................................................................... 4

Vehicle application guide ........................................................................................................... 5

Wiring connections ......................................................................................................................... 6

Main harness (H1), 12-pin black connector .................................................................................. 6

Relay harness (H2), 10-pin white connector .................................................................................. 6

Data harness (H3), 8-pin white connector ..................................................................................... 6

Analog input/output harness (H4), 22-pin white connector ............................................................. 7

RF Port harness (H5), 2-pin white connector .................................................................................. 7

D2D harness (H6), 4-pin white (1) and black (2) connectors ........................................................... 7

Temperature sensor harness (H7), 2-pin black connector ................................................................ 7

Installation (wiring diagram, fuse selection & vehicle wiring reference chart) .......................................... 8

Important! .............................................................................................................................. 10

Adjusting the 8504D Shock Sensor ........................................................................................... 10

When used in conjunction with SmartStart .................................................................................. 10

D2D 1.0/2.0 port configuration ............................................................................................... 11

Module programming .............................................................................................................. 12

LED diagnostics and troubleshooting .......................................................................................... 13

Soft reset ................................................................................................................................ 15

Hard reset .............................................................................................................................. 15

Learning the Tach (not needed with Virtual Tach) ............................................................................... 16

Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 16

Limited lifetime consumer warranty .................................................................................................. 17

Quick Reference Guide .................................................................................................................. 18

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.

• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:

• Never use a test light or logic probe when installing this unit. Always use a multimeter.

• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle.

• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to ﬁx the problem immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose signiﬁcant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a ﬂat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle.

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk.

DS4+ HK2

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device contains the FCC ID: EZSDEIBLE1 / IC: 1513A-DEIBLE1

Ce dispositive contient de la FCC ID: EZSDEIBLE1 / IC: 1513A-DEIBLE1

DS4+ HK2

Introduction

The HK2 ﬁrmware for DS4+ is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with speciﬁc Hyundai vehicles.

Warning! This module can only be programmed via the web tool, which can be found on

www.directechs.com or using the Directechs Mobile application for smartphones. Features and functions will become accessible when you connect the module using the XKLoader.

Pre-installation and application warnings

Firmware notes: This section highlights important information for this speciﬁc ﬁrmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness compatible

Keys required for programming

Keys required for

operation

 Unless speciﬁed otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic

connector.

 It is important to check that the fuses are positioned correctly in the module. Refer to the "Fuse selection" section following

each installation type for more information.

 Refer to the "Vehicle wiring reference chart" following each installation type.

General notes: This section highlights important information for this speciﬁc ﬁrmware.

[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. [2] The siren is only compatible with the Directed Digital remote start and security system. [3] The Green wire is only required for starter disable and antigrid connections.

Additional parts required (maximum required):

87a

86 85

0 x 1A Diodes

0 x Resistor

0 x Fuse

0 x Relay

DS4+ HK2

Vehicle application guide

PK-Immobilizer Bypass-Data No Key Req'd

RS-RAP Shut Down (Retained ACC Power)

••••••••••••••••••••••

The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles.

Vehicles

2015

2014

Hyundai

2013

Elantra GT • • •

end:

AV: Horn & Li

ht Controls

DL: OE Door Lock & Alarm Controls

nc CAN Interface w/ FOB Remote

FOB: S PK: Trans RS: Remote Start & En SS: Inte

onder & Immobilizer Override

ine Controls

rated Security & Monitorin

ST: Function/Feature Status

AV-Auto Headlamp Shutoff

AV-Panic Mode Activation

DL-Arm Factory Security

DL-Disarm Factory Security

DL-Door Lock Control

DL-Door Unlock

DL-Driver Priority Unlock

DL-Trunk / Hatch Release

FOB Control

RS-SmartStart 3.0 Compatible

RS-Tach / RPM Output

SS-Entry Monitoring ALL Door Pins

SS-Entry Monitoring Driver Door Pin

SS-Entry Monitoring Hood Pin

SS-Entry Monitoring Trunk/Hatch Pin

SS-Factory Alarm Trigger Monitoring

ST-Brake Status (foot brake)

ST-Door Locks Status

ST-E-Brake Status

ST-Ignition Status

DS4+ HK2

+ 14 hidden pages