Deglon 1520 User Manual

Parts

General Assembly - 1520 Model

Main Driveline
(pg. 55-56)

Hitch Assembly
(pg. 45)

Tie Bar Assembly (pg. 41)

Center Driveline (pg. 58)

Wing Driveline (pg. 57)

Left Wing
Assembly
(pg. 43)

Rephasing Cylinder,
3-1/4” x 8”
(pg. 54)

Left Wheel Strut

(Walking Axle
also available)

(pg. 48)

Center Shield
Assembly
(pg. 46)

Center Section
Assembly
(pg. 41-42)

Rephasing
Cylinder,
3-1/2” x 8”
(pg. 53)

Wing Driveline (pg. 57)
Right Wing Assembly (pg. 43)
Wing Lift Cylinder, 3” x 16” (pg. 53)
Rephasing Cylinder, 3” x 8” (pg. 54)

Right Wheel Strut

(Walking Axle
also available)
(pg. 48)

Pan, Blades, &
Hardware (pg. 50)

Rockshaft Assembly
(pg. 47)

Wheels, Hubs &
Spindles (pg. 49)

General Assembly - 1020 Model

Main Driveline
(pg. 55-56)

Hitch Assembly
(pg. 45)

Tie Bar Assembly (pg. 41)

Center Driveline (pg. 58)
Counterweight

Assembly (pg. 44)

Center Shield
Assembly
(pg. 46)

Center Section
Assembly
(pg. 41-42)

Rephasing
Cylinder,
3-1/2” x 8”
(pg. 53)

Wing Driveline (pg. 57)
Right Wing Assembly (pg. 43)
Wing Lift Cylinder, 3” x 16” (pg. 53)
Rephasing Cylinder, 3-1/4” x 8” (pg. 54)

Right Wheel Strut

(Walking Axle
also available)
(pg. 48)

Pan, Blades, &
Hardware (pg. 50)

Wheels, Hubs &
Spindles (pg. 49)

Rockshaft Assembly
(pg. 47)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-40-

Center Frame Assembly

500800 - Complete Tie Bar, (no pins) (2)

500805 - Tie Bar Clevis, Front (2)
118973 - Bolt, 1/2” x 2-3/4” UNC (4)
500819 - Pin, 1-1/4” x 2-1/16” (4)
118729 - Lock Nut, 1/2” UNC GRC

Unitorque (4)

118843 - Roll Pin,
1/4” x 1-1/2” (2)

See
Detail

118009 - Bolt, 1/2” x 1-1/4” UNC (2)
500813 - Pin, 1-1/4” x 4-7/8” (2)
118729 - Lock Nut, 1/2” UNC GRC Unitorque (2)
118901 - Lynch Pin, 3/16” x 1-1/2” (2)

118110 - Bolt, 5/16” x 1” UNC (4)
118530 - Lock Washer, 5/16” (4)
118731 - Flat Washer, 5/16” SAE (4)
160004 - Cone Shield, 9” Diameter (1)

118456 - Lock Nut, 1” UNC (2)
131020 - Flat Washer, 1” SAE (2)
500801 - Tie Bar Rod, 1” x 80” (2)

Center Driveline
160003 - (1000 RPM)
OR
160005 - (540 RPM)

133088 - Cap,

plastic (1)

See Detail

Use non-removable loctite
when replacing splitter box
bolt hardware.

118447 - Locknut, 5/8” (4)
118537 - Flat Washer, 5/8” (4)
117453 - Setscrew, 5/8” x 2-1/2” (4)
170011 - Splitter Gearbox 1000 RPM

OR
170021 - Splitter Gearbox 540 RPM

118336 - Grease Fitting, 1/4” (2)

118843 - Roll Pin, 1/4”
x 1-1/2” (2)

500804 - Tie Bar Clevis,
Rear - Threaded (2)

118495 - Jam Nut, 1” Heavy (2)

See
Detail

500910 - Cable, 1/4”
x 18” (1)

500911 - Cable, 1/4” x 21” (2)
(Optional)

500100 - Center

500600 - 3 Bolt Chain
Safety Bar (1)

118378 - Bolt, 5/8” x 1-3/4” (6)
118447 - Lock Nut, 5/8” GRC-Unitorque (6)
500853 - Center Skid Shoe (2)

118964 - Carriage Bolt, 3/8” x 3” (23)
118511 - Flat Washer, 3/8” (23)
118417 - Lock Nut 3/8” UNC GR5 (23)

Frame

See Detail

500604 - 4 Bolt Chain
Safety Bar (5)

500913 - Cable, 1/4” x 65” (1)
(Optional)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-41-

Center Frame Assembly

118901 - Lynch Pin, 3/6” x 1-1/2” (1)

118378 - Bolt, 5/8”x 1-3/4” (2)
118447 - Lock Nut, 5/8”

GRC-Unitorque (2)

118537 - Flat Washer,

5/8” SAE (2)

501005 - Urethane Bumper (2)

118982- Bolt, M8 x .125
x 20 P8.8 (2)

118556 - Lock Washer,
M8 (2)

118731 - Flat Washer,
5/16” SAE (2)

500719 - Shield Bumper Plate (1)

118795 - Bolt, 5/8” x 2-1/4” GR8 (6)
118537 - Flat Washer, 5/8” SAE (6)
118447 - Lock Nut, 5/8” GRC-Unitorque (6)

118447 - Lock Nut, 5/8” GRC-Unitorque (4)
143123 - Hose Holder Spring (4)
118537 - Flat Washer, 5/8” SAE (4)

118024 - Bolt, 5/8” x 1-1/2” UNC (4)

Counter Clockwise
170063 - Gearbox 1000 RPM

OR
170017 - Gearbox 540 RPM

Clockwise
170061 - Gearbox 1000 RPM

OR
170019 - Gearbox 540 RPM

118983 - Bolt, 1/4” x 3/4” (4)
118555 - Flat Washer, 1/4” (4)
133100 - Manual Holder (1)
118555 - Flat Washer, 1/4” (4)
118483 - Lock Nut, 1/4”

- Unitorque (4)

118483 - Lock Nut, 1/4”

- Unitorque (2)
142135 - SMV Sign (1)
118983 - Bolt, 1/4”

x 3/4” (2)

118005 - Bolt, 3/8”
x 1” UNC (2)

500137 - Bracket (1)
118417 - Lock Nut,

3/8” UNC (2)

118729 - Lock Nut, 1/2” GRC-Unitorque
500825 - Wing Float Link
117087 - Bushing, 1-1/4” OD x 1”
500817 - Pin, 1-1/4” x 2-7/16”
118112 - Bolt, 1/2” x 3” UNC

117111 - Bushing, 1-1/2” OD x 1” (2)

118087 - Bolt, 3/8” x 2” UNC
501007 - Rubber Spring
118417 - Lock Nut, 3/8” UNC

118957 - Transport Pin, 3/4” x 6”
118830 - Hair Pin, 3/16” x 3-1/4”

118729 - Lock Nut, 1/2” GRC-Unitorque (4)
500815 - Pin, 1-1/4” x 3” (4)
118009 - Bolt, 1/2” x 1-1/4” UNC (4)

2 of each
Req’d for
1520 Model

2 of each
Req’d for
1520 Model

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-42-

Right / Left Wing Assembly

(Right Wing Assembly Shown)

500608 - 5 Bolt Chain Safety Bar (3)

500912 - Cable, 1/4” x 71” (1)
(Optional)

500600 - 3 Bolt Chain
Safety Bar (2)

Wing Driveline
160002 - (1000 / 540 RPM)

500200 - Right Wing Frame (shown)
500201 - Left Wing Frame

500837 - Hinge Pin, 1-3/16” x 97-3/4”
118966 - Roll Pin, 5/16” x 1-3/4” (4)
500848 - End Retainer, 1-3/4” x 1” (2)
500612 - Hinge Safety Chain Bar (2)

500869 - Wing Skid Shoe - LH (1)
118729 - Lock Nut, 1/2” GRC Unitorque (6)
118512 - Flat Washer, 1/2” (6)

118642 - Carriage Bolt, 1/2” x 1-1/4” (6)
500868 - Wing Skid Shoe - RH (1)

118417 - Lock Nut, 3/8”
UNC GR5 (25)

118511 - Flat Washer,
3/8” (25)

118964 - Carriage Bolt,
3/8” x 3” (25)

500604 - 4 Bolt
Chain Safety Bar (1)

500914 - Cable,1/4” x 67” (1)
(Optional)

118982- Bolt, M8 x .125 x 20 P8.8 (4)
118556 - Lock Washer, M8 (4)
118731 - Flat Washer, 5/16” SAE (4)
160004 - Cone Shield, 9” Diameter (1)

133088 - Cap,

plastic (1)

Right Wing - Counter Clockwise
170005 - Gearbox 1000 RPM

OR
170015 - Gearbox 540 RPM

118795 - Bolt, 5/8” x 2-1/4” GR8 (6)
118537 - Flat Washer, 5/8” SAE (6)
118447 - Lock Nut, 5/8” GRC-Unitorque (6)

118972 - Jam Nut, 1-1/4” UNC GR2 (2)
500844 - Wing Link Adjustment (1)
117110 - Bushing, 1-1/4” OD x 3/4” (1)

117087 - Bushing, 1-1/4” OD x 1” (1)

Left Wing - Clockwise
170003 - Gearbox 1000 RPM

OR
170013 - Gearbox 540 RPM

118962 - Lock Nut, 1-1/4” UNF GR8 (1)
131206 - Flat Washer, 1-1/4” SAE (1)
500331 - Bolt, 1/4” UNF X 7 1/2”

GR8 PL (1)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-43-

Counterweight Assembly

118966 - Roll Pin, 5/16” x 1-3/4” (2)

500837 - Hinge Pin, 1-3/16” x 97-3/4” (1)

(1020 Model Only)

500265 - Counterweight Frame (1)
500870 - Counterweight Skid (1)

118984 - Bolt, 1-1/4” x 3” GR5 (2)
500257 - Bolt Plate (2)
118445 - Lock Nut, 1-1/4” GR5 (2)

500869 - Wing Skid Shoe - LH (1)

500260 - Weight Plate, 1” (12)
118456 - Lock Nut, 1” GR5 (6)
118520 - Flat Washer, 1” (6)

117436 - Bolt, 1” x

8-1/2” GR5 (6)

118417 - Lock Nut, 3/8”
UNC GR5 (4)

306356 - Chain, 5/16”

- 11 Links (4)

118511 - Flat Washer, 3/8” (8)

118136 - Bolt, 3/8” x 1-1/2” (4)

500868 - Wing Skid Shoe - RH (1)
118642 - Carriage Bolt, 1/2” x 1-1/4” (10)
118587 - Flat Washer, 1/2” F436 PL (10)
118729 - Lock Nut, 1/2” GRC Unitorque (10)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-44-

Hitch Assembly

143111 - Hose Holder (1)
118024 - Bolt, 5/8” x 1-1/2” UNC (1)
118514 - Washer, 5/8” (1)
118447 - Lock Nut, 5/8” UNC

Unitorque (1)

118336 - Grease Fitting, 1/4” (1)

118962 - Lock Nut, 1-1/4” UNF GR8 (1)

131206 - Flat Washer, 1-1/4” SAE (1)
500312 - Swivel Hitch (1)

500300 - Hitch Frame (1)
118422 - Lock Nut, 3/4” UNC (3)
118516 - Flat Washer, 3/4” (6)
500328 - Jack Holder (1)
118043 - Bolt, 3/4” x 2” UNC (3)

117111
Bushing (2)

132051 - Sidewind
Jack (1)

118929 - Lock Pin, 3/8”
x 1-1/2” (1)

500330 - Bolt, 1-1/4”
x 7-1/2” UNF
c/w Grease Fitting (1)

118336 - Grease Fitting, 1/4” (1)

Precision Hitch Assembly

500340 - Precision Hitch Assembly

- includes -

118965 - Bolt, 1-1/4” x 5-1/2” UNF GR8 (1)
500325 - Washer, 4” OD (1)
118951 - Retainning Ring, 2” Ext. (1)
500318 - Hitch Tongue (1)

- includes -

118950 - Bushing, 2-1/2” OD (1)

118336 - Grease Fitting, 1/4” (1)

500324 - Bushing, 4” OD (1)
500327 - Washer, 3” OD (1)
118962 - Lock Nut, 1-1/4” UNF GR8 (1)

118952 - Cotter Pin, 5/16” x 3-1/2” (1)
118457 - Castle Nut, 1-1/2” UNF GR5 (1)
500326 - Flat Washer, 4” OD (1)
117082 - Bushing, 83.2mm OD (2)
116244 - Safety Chain, -10,100 lbs (1)

Clevis Hitch Assembly

500335 - Hitch Clevis

- OR -

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-45-

Center Shield and Hydraulic Hose Clamps

500715 - Center Shield Assembly (1)

- includes -

133093 - Capscrew, M8 x 1.25 x 30mm (2)
133092 - Plastic Handle (1)
133094 - Nut, M8 x 1.25mm (2)

Single Acting Hose Clamp Layout

118144 - Bolt, 5/16
x 1-1/2 UNC (2)

780279 - Top Plate (2)

780278 - Hose Clamp Block (2)

Hose Clamp Layout Assembly
(See Detail Below)

Double Acting Hose Clamp Layout

118945 - Bolt, 5/16
x 2-3/4 UNC (1)

118144 - Bolt, 5/16
x 1-1/2 UNC (1)

780279 - Top Plate (2)

780278 - Hose Clamp Block (3)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-46-

Rockshaft Assembly

Rockshaft Suspension Detail

Preloading of rubber spring required
on all strut assemblies. Exposed
thread length should be
approximately 1/2”
when using correct
hardware.

1/2”

117454 - Bolt,

1-1/4” x 8“

UNF GR8

500840 - Transport Lock

243500 - Lock Pin, 5/16” x 2-1/2”

131020 - Flat Washer 1” SAE (2)

118966 - Roll Pin, 5/16” x 1-3/4” (2)
500412 - Pin, 1” x 4-11/16”

500400 - Rockshaft

117111 - Bushing,
1-1/2” OD x 1”

118962 - Lock Nut,
1-1/4” UNF GR8

131206 - Flat Washer,
1-1/4” SAE

131206 - Flat Washer, 1-1/4” SAE

118962 - Lock Nut, 1-1/4” UNF GR8

500330 - Bolt, 1-1/4”
x 7-1/2” UNF
(c/w Grease Fitting)

Walking Axle

500726 - Walking Axle (opposite confi guration)
500725 - Walking Axle

500730 - Lower Strut

(Strut Only)

118447 - Lock Nut, 5/8”
UNC GRC -Unitorque

117462 - Flat Washer, 5/8”
501003 - Bumper, 2” x 5/8”

501006 - Rubber Spring
117461 - Bolt, 5/8” x 6” UNC GR8

118336 - Grease

Fitting, 1/4” (1)

Hub & Spindle Assembly (2)
(see detail on page 49)

118644 - Bolt, 3/8” x 3” UNC GR5 (2)

118417 - Lock Nut, 3/8” UNC GR5 (2)

117082 - Bushing, 83.2mm OD (2)
500729 - Pin, 2-7/8” OD x 5-3/4” (1)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

-47-

Wheel Strut Assemblies

Wing Suspension Detail

Preloading of rubber spring required
on all strut assemblies. Exposed
thread length should be
approximately 3/8”
when using correct
hardware.

3/8”

Suspension Components

117461 - Bolt, 5/8” x 6” UNC GR8
501006 - Rubber Spring

501003 - Bumper, 2” x 5/8”
117462 - Flat Washer, 5/8”

118447 - Lock Nut, 5/8” UNC
GRC -Unitorque

Lower Strut
Double Wheel

Upper Strut
Common

500450 - Upper Strut,

- Right Side (Not Shown)

500455 - Upper Strut,

- Left Side (Shown)

500330 - Bolt, 1-1/4”
x 7-1/2” UNF
(c/w Grease Fitting)

131206 - Flat Washer,1-1/4” SAE
118962 - Lock Nut,1-1/4” UNF GR8

Lower Strut
Single Wheel

500730 - Lower Strut,
Double Wheel - Common

118963 - Flat Washer, 1-1/4IN GR8 (1)
118962 - Lock Nut, 1-1/4” UNF GR8 (2)
117454 - Bolt, 1-1/4” x 8“ UNF GR8 (2)

Walking Axle

500726 - Walking Axle - Right Wing (not shown)
500725 - Walking Axle - Left Wing

500735 - Lower Strut,
Single Wheel

118417 - Lock Nut,
3/8” UNC GR5

118644 - Bolt, 3/8”
x 3” UNC GR5

Hub & Spindle Assembly
(see Detail on page 49)

118336 - Grease

Fitting, 1/4” (1)

Hub & Spindle Assembly (2)
(see detail on page 49)

143245 - Rotary Cutter 1020/1520 (30-March-2007)

118644 - Bolt, 3/8” x 3” UNC GR5 (2)

118417 - Lock Nut, 3/8” UNC GR5 (2)

117082 - Bushing, 83.2mm OD (2)
500729 - Pin, 2-7/8” OD x 5-3/4” (1)

-48-