Degelman Landroller LRX Series, Landroller LRX36, Landroller LRX41, Landroller LRX 46, Landroller LRX51 Quick Start Manual
...
QUICK-START GUIDE
T
O
B
E
E
L
I
G
I
B
L
E
F
O
R
Y
O
U
M
U
S
T
R
E
G
I
S
T
E
R
WARRANTY
REMEMBER! You must complete Product
Registration to be eligible for Warranty.
*
for LRX LANDROLLERS
* Refer to operators manual for complete safety and operation info.
1
Connect Hydraulics
A
Opening into Field Position
B
LATCH & END WHEELS....Latch & End Wheel Cylinders
2
SWING ARM CIRCUIT..................Power-fold Cylinders
3
CTR WHEEL & FLOAT....Hitch & Center Wheel Cylinders
1) Drive the LRX Landroller onto an area of level ground
large enough to open the wings. Ensure the Landroller is
positioned straight behind the tractor.
2) Remove the four Red Transport Bars from the End Wheel
& Center Wheel cylinders. Place the transport bars onto
the frame mounted storage brackets and secure with the
lock-pins.
2
Note: You may need to activate (extend) the
hydraulic cylinders slightly to allow easier
removal of the cylinder Transport Bars.
3) Activate the End Wheel
Cylinders to completely
raise the end wheels and
1
1
lower the ends of the
drums to the ground.
4) Extend the Power-fold Cylinders to fully open the
2
wings. Ensure the swing-arm shafts properly latch into
place.
4
2
2
4
4
6) Retract the Center Frame Cylinders to raise the center
3
frame wheels (lowering the center section to the ground).
3
3
6
6
7) Remove the Red
Transport Pin from the
float hitch and secure
it in storage position.
8) Open the Hydraulic
Ball Valve.
3
9) Retract the Hitch Cylinder
to place the Landroller into Float Position.
10) The LRX Landroller should now be in the proper position
for field use. Read manual for further information.
3
8
3
9
7
5) IMPORTANT:
Retract the
5
POWER-FOLD
Cylinders
Remember to retract
the Power-fold
Cylinders back into
the fully closed position
before use.
2
2
(Refer to operators manual for complete safety and operation info.)
Maintenance
2
• Check for missing, worn or damaged parts.
• Working points & pins
• Hydraulic Connections & Hoses
• Hubs & Spindles
(Check Machine Daily)
143376 v1.1
Moving Into Transport Position
C
1) Drive the LRX Landroller onto an area of level ground with plenty
of room to drive straight forward.
1
5) IMPORTANT: Ensure the POWER-FOLD
Cylinders are RETRACTED (closed)
Ensure that the Power-Fold Cylinders have been fully retracted
before moving forward. Failure to do so could damage the
Power-Fold cylinders and require replacement.
2
2) Fully extend the Front Hitch & Center Frame Cylinders.
This places the float hitch
into Transport Position
and also fully lowers the
Center Frame Wheels
(raising the center section
off the ground).
IMPORTANT:
3)
• Secure the Float Hitch
in place with the Red
Transport Pin.
• Close the Hydraulic Ball Valve.
4) Completely extend the End Wheel & Latch Cylinders to lower
the End Wheels and open the Swing-Arm Latches.
1
3
3
2
1
3
3
1
4
4
6) Drive forward until roller wings trail straight behind tractor.
5
6
1
4
7) Install the four Red Transport Bars onto the End Wheel &
Center Wheel cylinder shafts and secure in place using the
lock-pins.
Ensure front Red Transport Pin has also been installed correctly
into the float hitch (refer to step 3).
8) Read and follow necessary safety procedures outlined in
Transport Safety section of the manual.
Loading...