OPERATOR MANUAL
& PARTS CATALOG
DEGELMAN INDUSTRIES LTD.
BOX 830-272 INDUSTRIAL DRIVE,
REGINA, SK, CANADA, S4P 3B1
FAX 306.543.2140 PH 306.543.4447
1.800.667.3545 DEGELMAN.COM
143351 v1.3
JOHN DEERE
9R SERIES - FT4
9370R, 9420R, 9470R, 9520R, 9570R, 9620R
QUICK GUIDE INDEX
Introduction 1
Safety 2
Operation 4
Maintenance 6
Transport & Storage 11
Troubleshooting 12
Blade Attachments 13
Blade Components 14
Pivot & Main Frame 15
Mounting Brackets
Single Reduction (SR) Axle Models 16
Double Reduction Axle Models with
HydraCushion™ Suspension (HC) 18
Double Reduction (DR) Axle Models 20
Mounting Brackets - Optional Mounts 21
Cylinders 22
Hydraulic Routing 23
Mounting Procedure 27
Warranty 28
Record Serial Number:
...........................................................
DEGELMAN INDUSTRIES LTD.
BOX 830-272 INDUSTRIAL DRIVE,
REGINA, SK, CANADA, S4P 3B1
FAX 306.543.2140 PH 306.543.4447
1.800.667.3545 DEGELMAN.COM
IMPORTANT:
READ MANUAL
Introduction
WELCOME
Degelman is proud to welcome you to our rapidly
increasing family of high quality and dependable
product owners. This product was designed and
built specifically for you, the customer. Through our
research and with your input and feedback, we
present to you our 69/7200 Series Dozer Blades.
Designed with durability, safety, and performance in
mind, this dozer blade is ready for years of quality
service. In order to help you keep your dozer blade
in top operating condition we have provided you
with this manual.
ABOUT THIS MANUAL
This manual has been designed to help you with
three extremely important issues: Operation, Safety,
and Maintenance. It is strongly recommended that
you read through the entire manual and review it
annually for:
• your own personal safety.
• the safety of others.
• helpful and effective operation
techniques.
• maintenance procedures.
• preventative maintenance.
Your authorized Degelman dealer can be contacted
for ordering any replacement parts, decals, or
manuals. Since many of our parts are specially
designed specifically for this dozer blade we
strongly recommend you always replace them with
genuine Degelman parts only.
This manual and its contents were current at the time
of its first printing. To increase product performance
and operation, some part modifications and changes
may occur that are not reflected in this manual.
Note: The description “Right”or“Left” as used in this
manual is determined by the direction the tractor
will travel while in use (unless otherwise stated).
PROOF OF OWNERSHIP
Serial Number Plate
Your serial number is
found on the serial number plate.
It is important to record the serial and model
number of your dozer for proof of ownership and
for any required service or maintenance assistance.
Serial Number
Owner Name
Model
Purchase Date
Dealer Name
Address
Phone
DESCRIPTION
The 69/7200 Dozer Blades consists of a dozer
blade connected to a pivot/main frame assembly.
Typically, this assembly mounts to side and axle
brackets that are bolted securely onto the frame of
your tractor.
The blade is attachable/detachable with a simple
HQT (Hydraulic Quick-Tach) mounting system and
hydraulic hook-up.
The 6900 Blade has two hydraulically controlled
ranges of motion – lift & angle.
Left
Side
143351 - 69/7200 Series (12-May-2017)
Right
Side
The 7200 Blade has three hydraulically controlled
ranges of motion – lift, angle & tilt.
Lift Angle Tilt
(7200 Only)
-1-
Safety
Why is SAFETY
important to YOU?
3 BIG Reasons:
• Accidents Can Disable and Kill
• Accidents Are Costly
• Accidents Can Be Avoided
SAFETY ALERT SYMBOL
The Safety Alert Symbol means:
ATTENTION!
BECOME ALERT!
YOUR SAFETY IS INVOLVED!
The Safety Alert Symbol identifies important safety
messages applied to the dozer blade and in this
manual. When you see this symbol, be alert to the
possibility of injury or death. Follow the
instructions provided on the safety messages.
YOU are RESPONSIBLE
. . . for your own safety and that of others!
- If you are not familiar with basic agriculture &
industrial safety, you must get training.
- Owners of equipment must give operating
instructions to other operators such as family
members or a hired hand.
- Making any design changes to equipment could
cause a hazard, damage your machine & void
your warranty.
YOU are responsible for the SAFE operation and
maintenance of your Degelman implement. YOU
must ensure that you and anyone else who is going
to operate, maintain, or work around the machine
be familiar with the operating and maintenance
procedures, and related SAFETY information
contained in this manual. This manual will take you
step-by-step through your working day and will
alert you to good safety practices that should be
adhered to while operat ing this equipment.
Remember, YOU are the key to safety. Good
safety practices not only protect you, but also
the people around you. Make these practices a
working part of your safety program. Be certain
that EVERYONE operating this equipment is familiar
with the recommended operating and maintenance
procedures and follows all the safety precautions.
Most accidents can be prevented. Do not risk injury
or death by ignoring good safety practices.
SIGNAL WORDS
Note the use of the Signal Words: DANGER, WARNING,
and CAUTION with the safety messages. The appropriate
Signal Word has been selected using the following
guidelines:
DANGER: Indicates an imminently hazardous situation
that, if not avoided, WILL result in death or serious injury
if proper precautions are not taken.
WARNING: Indicates a potentially hazardous situation
that, if not avoided, COULD result in death or serious
injury if proper precautions are not taken.
CAUTION: Indicates a potentially hazardous situation
that, if not avoided, MAY result in minor or moderate
injury if proper practices are not taken, or, serves as a
reminder to follow appropriate safety practices.
143351 - 69/7200 Series (12-May-2017)
• Owners must give operating instructions to
operators or employees before allowing them to
operate the unit, and at least annually thereafter
per OSHA regulation 1928.57.
• The most important safety device on this
equipment is a SAFE operator. It is the operator’s
responsibility to read and understand ALL Safety
and Operating instructions in the manual and to
follow these. All accidents can be avoided!
• A person who has not read and understood ALL
operating and safety instructions is not qualified
to operate the machine. An untrained operator
exposes himself and bystanders to possible
serious injury or death.
• Do not modify the equipment in any way.
Unauthorized modifica tion may impair the
function and/or safety and could affect the life of
the equipment.
-2-
Safety
GENERAL SAFETY
1. Read and understand the Operator's Manual
and all safety signs before using. Review safety
related items with all operators annually.
2. Lower blade to ground, stop tractor engine,
place all controls in neutral, set park brake and
remove ignition key before servicing, adjusting
or repairing.
3. Keep hands, feet, hair and clothing away from
all moving and/or rotating parts.
4. DO NOT allow riders on the machine or tractor
during operation or transporting.
5. Clear the area of all bystanders, especially
children, before starting.
6. DO NOT operate machine on steep side hills or
slopes.
7. Be careful when working around or maintaining
a high-pressure hydraulic system. Ensure all
components are tight and in good repair before
starting.
8. Clean all reflectors, lights and the SMV sign
before transporting on a highway or public
road. Be sure to check with local highway
authorities and comply with their lighting
requirements.
9. Stay well back from machine when operating.
Keep others away.
10. DO NOT operate the Dozer without an
adequate amount of rear wheel ballast.
Wear Protective Equipment
Note: Before working on machine, always turn
tractor off, set controls in neutral, and remove
ignition key.
• Wear proper safety equipment such
as safety glasses and shoes, hearing
protection, hard
hats, or any other
appropriate items
to prevent injury.
• Loss of hearing or hearing impairment may result
from prolonged exposure to loud noise. Wear
suitable hearing protective devices such as
earmuffs or earplugs to protect your hearing.
• Safely operating this equipment requires the full
attention of the operator. Do not wear radio or
music headphones, or talk on your phone while
operating this machine. Never operate while
under the influence of alcohol or drugs or allow
anyone under the influence to operate the tractor.
HYDRAULIC
• Keep all parts clean.
• Replace worn or damaged parts.
• Don’t try any makeshift repairs.
• Before operating check that everything is tight and
not broken.
• Wear gloves and eye protection when searching
for leaks. Use a piece of wood or cardboard but
not your hand. High pressure oil will penetrate
your skin. If that happens you risk serious injury.
Prepare for Emergencies
• Keep a first aid kit and
fire extinguisher handy.
• Keep emergency numbers
for doctor, hospital, ambulance, and
fire department near your phone.
Doctor
Ambulance
Hospital
Fire Department
143351 - 69/7200 Series (12-May-2017)
BLADE
• Lower blade to the ground when not in use.
• Keep clear of blade when tractor is running.
• Keep hands & feet away from under blade.
• Turn engine off when hooking up hydraulics.
TRANSPORTING
• Lift blade up then hold with safety chain.
• Make sure SMV sign & reflectors are clean.
• Use your hazard lights.
-3-
Operation
TO THE NEW OPERATOR OR OWNER
The Degelman Dozer Blade is a push type tractor
attachment designed primarily for excavating,
levelling and filling of dirt, snow and silage.
It is the owners or operators responsibility to read
this manual carefully to learn how to operate
the machine safely and how to set it to provide
maximum efficiency. Safety is everyone’s business.
By following safe operating practices, a safe
environment is provided for the operator and
bystanders.
The manual will take you step-by-step through
your working day. By following the operating
instructions in conjunction with a good
maintenance program your machine will provide
many years of trouble-free service.
PRINCIPLES OF OPERATION
The dozer blade consists of a blade/cutting edge
unit attached to a pivot-main frame combination
suspended from the tractor by the front and side
mount brackets. By driving the tractor forward
with the blade either straight ahead or angled,
and allowing the cutting edge to run just under the
ground surface - dirt, silage or snow is relocated
as desired.
BREAK-IN
Although there are no operational restrictions on
the Dozer Blade when it is new, there are some
mechanical checks that must be done to ensure
the long term integrity of the unit. When using the
machine for the first time, follow this procedure:
TRACTOR PREPARATION
1. Wheel Spacing
Important: To avoid possible damage from
over stressing tractor axles, use no tire combination
which results in overall width greater than the
width of the angle blade.
Important: Before beginning operation, turn
the wheel fully to the right and left to be sure there
is sufficient clearance between the tires and the
angling cylinders. If necessary, move the wheels
to a wider setting to provide clearance. See your
Tractor Operator's Manual.
2. Rear Wheel Weight and Tire Inflation:
Add necessary rear end weights for efficient
operation and safety. Any of the cast-iron weights
recommended for your tractor or liquid in the tires,
may be used for necessary ballast. Be sure the
weight is distributed equally on each rear wheel.
Inflate front and rear tires to proper pressure as
recommended in the Tractor Operator’s Manual for
heavy front-mounted implements.
3. Checking Hydraulic Oil Level:
Check the oil level in the tractor hydraulic system
daily. Refer to your tractor operator's Manual for
Instructions. Keep the oil supply up to the proper
level. Before checking oil supply, fully extend
and retract angle and lift cylinders 3 - 4 times and
return the blade to the ground.
ATTACHING THE DOZER BLADE
A. Before using:
1. Read Operator's Manual.
2. Lubricate all points shown in the
Maintenance Section.
3. Check all bolt tightness.
B. After operating for 2 hours:
1. Check all hardware.
2. Check all hardware tightness.
3. Check all hydraulic system connections.
Tighten if any are leaking.
C. After operating 10 hours:
1. Repeat Step B.
2. Go to the service schedule as outlined in the
Maintenance Section.
143351 - 69/7200 Series (12-May-2017)
NOTE: Please refer to the assembly section of this
manual - for full instructions for attaching your
specific tractor and blade model.
BLEEDING THE HYDRAULICS
Before beginning operation, bleed the hydraulic
system to remove any air. To do this, cycle the
hydraulics several times by holding the cylinder
fully extended for several seconds. This will cause
any trapped air to be purged from cylinder.
COLD WEATHER OPERATION
To assure smooth operation in cold weather, cycle
the cylinders several times to warm the oil in the
hydraulic system.
-4-
Operation
OPERATOR’S RESPONSIBILITY
Every operator should read this manual and
be instructed in safe operating procedures. An
untrained operator is not qualified to operate this
machine and could place themselves or bystanders
in danger.
OPERATING SPEED
For normal operation, operate the tractor at a
comfortable or manufacturer recommended speed.
When operating over rough terrain or limited to
space, reduce engine speed. The actual forward
speed will be determined by tractor horsepower,
land density and depth of cut.
Experience will teach you the most efficient operating
speed, but as a rule 3-4 MPH (5-7 km/h) is a normal
operating range.
FLOATING THE DOZER BLADE
Here are some the things you can do with your
hydraulic system in float position:
• Skim the top of pavement
• Run on the skid shoes
• Back drag
BLADE DEPTH
Gauge the depth of cut to push the most material
possible without losing speed through spinning
the wheels or slowing the tractor engine. Do this
by setting the depth shoes, and by regulating the
depth for the blade height with the lifting cylinder
operating lever.
The distance the material is pushed should be kept
to a minimum. Dig and cut the material downgrade
whenever possible.
DEPTH/SKID SHOES
Soft uneven ground
• Skid shoe low
• Blade high
Blade
High
Skid Shoe
Low
Hard even ground
• Skid shoe high
• Blade low
Blade
Low
Skid Shoe
High
By placing the remote cylinder operating lever for
the lift function in float position, the blade may be
used to smooth an area by running the tractor in
reverse (refer to Tractor Operator's Manual). On
moderate grades, the tractor can be driven up
the slope and the blade dropped down for backdragging. It may also be used to push dirt or snow
on pavement or other smooth surfaces.
ANGLING DOZER BLADE
The dozer blade can be hydraulically angled
approximately 30° to the right or left by operating
the proper tractor remote cylinder lever. In the
angled position, the dozer blade can be used
for backfilling trenches, side-casting into ditches,
levelling and grading.
A dual relief valve is incorporated to protect
the hydraulic angling system when the blade is
overloaded. (This valve will bypass the hydraulic
fluid and diminish the degrees that the blade was
initially angled.)
Important: To avoid damage to tractor or
blade, the hydraulic system must be hooked up
properly including line to hydraulic tank drain.
PRE-OPERATION CHECKLIST
Efficient and safe operation of the Dozer Blade
requires that each operator reads and understands
the operating procedures and all related safety
procedures outlined in this manual.
Before Using for the FIRST Time
• Lubricate all points
• Torque all hardware to correct setting
• Check hardware torque & hydraulics
after the first 2 hrs & again after 10 hrs.
Before Using EVERY Time
Check: • If all points lubricated
• All components attached securely
• Condition of cutting edge
• Depth/skid shoe wear
• Hydraulics:
- Tractor’s oil reservoir
- Condition of hoses, lines & fittings
143351 - 69/7200 Series (12-May-2017)
-5-
Maintenance
MAINTENANCE SAFETY
1. Review the Operator’s Manual and all safety
items before working with, maintaining or
operating the machine.
2. Lower machine to ground, stop the tractor
engine, place all controls in neutral, set
park brake and remove ignition key before
servicing, adjusting or repairing.
3. Clear the area of bystanders, especially
children when carrying out any maintenance
and repairs or making adjustments.
4. Place safety stands or large blocks under
the frame before removing tires or working
beneath the machine.
5. Be careful when working around or
maintaining a high-pressure hydraulic system.
Wear proper eye and hand protection when
searching for a high pressure hydraulic leak.
Use a piece of wood or cardboard as a
backstop when searching for a pin hole leak
in a hose or a fitting.
LUBE AFTER EVERY 8 HRS.
Items to Grease Qty.
Angle Cylinder Pins 2 per cylinder
Lift Cylinder Pins 2 per cylinder
Tilt Cylinder Pins 2 per cylinder
Blade Pivot Pin 1 on left side
Tilt Ring 2 per side
Tilt Bell Plate 1 per side
Side Bracket Pins 1 per side
Main Pivot Pins 1 per side
Tilt Cylinder Pins
(7200)
(7200)
(7200)
6. Always relieve pressure before disconnecting
or working on hydraulic system.
GREASING
1. Use only a hand-held grease gun for all
greasing.
2. Wipe grease fitting with a clean cloth before
greasing, to avoid injecting dirt.
3. Replace and repair broken fittings
immediately.
4. If fittings will not take grease, remove and
clean thoroughly. Also clean lubricant
passageway. Replace fitting if necessary.
5. Inject grease until you see grease being
expelled from the pin or bushing areas.
Tilt Ring
Tilt Bell Plate
(Typical both sides)
Side Bracket Pins
(Both sides)
Main/Pivot Pins
(Both sides)
Please note: The frame assemblies for your particular fit-up
may differ significantly from those shown in the diagram,
however, the basic grease points should be similar.
Lift Cylinder Pins
(Both sides)
Angle Cylinder Pins
(Both sides)
Blade Pivot Pin
143351 - 69/7200 Series (12-May-2017)
-6-
Maintenance
HYDRAULIC SAFETY
1. Always place all tractor hydraulic controls in
neutral before dismounting.
2. Make sure that all components in the hydraulic
system are kept in good condition and are clean.
3. Replace any worn, cut, abraded, flattened or
crimped hoses and metal lines.
4. Do not attempt any makeshift repairs to the
hydraulic lines, fittings or hoses by using tape,
clamps or cement. The hydraulic system operates
under extremely high pressure. Such repairs will
fail suddenly and create a hazardous and unsafe
condition.
5. Wear proper hand and eye protection when
searching for a high pressure hydraulic leak. Use a
piece of wood or cardboard as a backstop instead
of hands to isolate and identify a leak.
6. If injured by a concentrated high-pressure stream of
hydraulic fluid, seek medical attention immediately.
Serious infection or toxic reaction can develop from
hydraulic fluid piercing the skin surface.
7. Before applying pressure to the system, make sure
all components are tight and that lines, hoses and
couplings are not damaged.
Think SAFETY! Work SAFELY!
HARDWARE TORQUE SETTINGS
The tables below give correct torque values for various
bolts and capscrews. Tighten all bolts to values in
charts unless otherwise noted. Check tightness of bolts
periodically, using torque charts as a guide. Replace
hardware with the same strength (Grade/Class) bolt.
IMPERIAL TORQUE SPECIFICATIONS
(based on “Zinc Plated” values)
SAE-5 SAE-8
Size Grade 5 Grade 8
1/4” 7 (10) 10 (14)
5/16” 15 (20) 20 (28)
3/8” 25 (35) 35 (50)
7/16” 40 (55) 60 (80)
1/2” 65 (90) 90 (120)
9/16” 90 (125) 130 (175)
5/8” 130 (175) 180 (245)
3/4” 230 (310) 320 (435)
7/8” 365 (495) 515 (700)
1” 550 (745) 770 (1050)
1-1/8” 675 (915) 1095 (1485)
1-1/4” 950 (1290) 1545 (2095)
1-3/8” 1250 (1695) 2025 (2745)
1-1/2” 1650 (2245) 2690 (3645)
lb.ft (N.m) lb.ft (N.m)
CHECK HARDWARE TORQUE
Important: Check torque on all
hardware periodically. Check after
first 2, 10, 40, then every 200 hours.
• Torque values listed are for general
use only. If a different torque value
or tightening procedure is specified for a specific
application, do not use these values.
• Refer to the “Parts” section for proper grade and
length of bolts for replacement parts.
• Do not replace locknuts with nuts and lock washers.
Replace all parts with original, specified parts only.
• Dry values shown mean the bolt/nut is plain or zinc
plated without any lubrication.
Unless otherwise stated:
Hardware - Hex, GR5 UNC (imperial) or P8.8 (metric)
Hoses - 3/8, ends come with 3/4 JIC female swivel.
TORQUE
all hardware
METRIC TORQUE SPECIFICATIONS
(based on “Zinc Plated” values)
8.8 10.9
Size Class 8.8 Class 10.9
M6 7 (10) 10 (14)
M8 16 (22) 23 (31)
M10 30 (42) 45 (60)
M12 55 (75) 80 (108)
M14 90 (120) 125 (170)
M16 135 (185) 195 (265)
M18 190 (255) 270 (365)
M20 265 (360) 380 (515)
M22 365 (495) 520 (705)
M24 460 (625) 660 (895)
M27 675 (915) 970 (1315)
M30 915 (1240) 1310 (1780)
M33 1250 (1695) 1785 (2420)
M36 1600 (2175) 2290 (3110)
lb.ft (N.m) lb.ft (N.m)
HYDRAULIC FITTING TORQUE
Size lb.ft (N.m)
3/4 75 (100)
7/8 90 (122)
143351 - 69/7200 Series (12-May-2017)
-7-
Maintenance
HYDRAULIC CYLINDER REPAIR
PREPARATION
Types of Cylinders
When cylinder repair
(Wire Ring / Threaded Head)
is required, clean off
unit, disconnect hoses
and plug ports before
removing cylinder.
When removed, open
the cylinder ports and
drain the cylinder's
hydraulic fluid.
Examine the type of
Set Screw
cylinder. Make sure
you have the correct
tools for the job.
You may require the
following tools:
• Proper Seal Kit
Locking Ring
• Rubber Mallet
• Screwdriver
• Punch
• Pliers
• Emery cloth
• Torque Wrench
REPAIRING A WIRE RING CYLINDER
Wire Ring
Threaded
Head
Threaded
Head
5. Take the plastic removal ring from the seal kit:
a) Straighten the ring and remove any kinks or
excessive curl to make installation easier and
prevent it from falling out.
b) Insert the removal ring into the internal
groove with the feathered
end pointing into the tube.
5
c) Use a screwdriver or a finger to hold one end of
the ring in the groove while fitting the other end
of the ring into the groove. The tips should snap
in together. Ensure it is secure and fully seated
before the next step.
IMPORTANT: It is important to ensure the
removal ring is completely in the groove
before pulling the rod out. If the ring sticks out
it will get stuck between the head and tube.
6. a) Extend the rod to pull head out of tube. If the
rod does not pull out easily, push the head back
in and ensure the ring is properly in the groove.
Replace ring if necessary.
1. Retract the rod assembly.
2. Remove the external steel wire ring.
2
Inner Ring
Initial Ring Positions
External Ring
3. Remove any dirt that may have accumulated on
the cylinder head.
4. Using the mallet and punch, push the head
into the cylinder tube until the
internal tube groove
4
is fully exposed.
This will also move the
internal wire ring into
its removal position.
Inner Ring
Internal Groove
4
Outer
Wire Ring
(Removed)
Inner Wire Ring
6
Plastic Ring
Note: Excessive force will not overcome a
jammed ring and could damage the cylinder.
b) Completely remove rod and head from tube.
7. Remove plastic removal ring from the cylinder
tube.
7
143351 - 69/7200 Series (12-May-2017)
-8-
Maintenance
8. Remove locknut, piston and head from rod.
Piston Seal (2pcs)
Wear Ring
Locknut
Piston
Head/Gland
Wear Ring
Wiper Seal
U-Cup Rod Seal
O-Ring
Dual Seal
9. a) Inspect and replace all of the seals with new
components.
b) Inspect the inside of the cylinder barrel,
piston, rod and other polished parts for burrs
and scratches. Smooth areas as needed with an
emery cloth.
c) During re-assembly of head/gland assembly,
leave the outer O-Ring Dual Seal loose on the
rod to re-install at a later step.
10. Replace piston and torque the locknut to
required value. (Refer to chart below)
11. b) Tighten the band clamp to ensure the wire
ring is fully seated. Then, loosen the clamp
approx. 1/2 a turn to allow band clamp to slide
during final assembly.
12. Lubricate the cylinder tube and piston seals.
13. Insert the piston into the tube. Tap the cylinder
head into the tube until the clamp slides over
and the inner wire ring is inside the tube.
13
14
15
14. Loosen the clamp and remove.
15. Install the O-Ring Dual seal.
16. Tap the head the rest of the way until the end is
flush with the tube.
16
O.D. Threads =
Locknut Size
LOCKNUT SIZE (PISTON) TORQUE VALUE
3/8 - 24 UNF 25-30
1/2 - 20 UNF 40-60
5/8 - 18 UNF 95-105
3/4 - 16 UNF 175-225 lb.ft
7/8 - 14 UNF 200-275
1 - 14 UNF 300-380 lb.ft
1 1/8 - 12 UNF 400-500
1 1/4 - 12 UNF 500-600
1 1/2 - 12 UNF 700-800
1 3/4 - 12 UNF 800-900
lb.ft (35-42 N.m)
lb.ft (55-80 N.m)
lb.ft (130-140 N.m)
(240-305 N.m)
lb.ft (270-370 N.m)
(405-515 N.m)
lb.ft (540-675 N.m)
lb.ft (675-810 N.m)
lb.ft (950-1085 N.m)
lb.ft (1085-1220 N.m)
11. a) Install the supplied band clamp to compress
the inner wire ring on the head/gland assembly
so it will fit into the tube.
Note: Make sure the cam of the band clamp is
not overtop of the gap in the ring.
Flush with edge
IMPORTANT: The head/gland must be inserted until
it is flush with the tube to allow the inner wire ring to
snap into its seated position in the internal cylinder
groove. Failure to insert the head flush as shown will
result in the head and rod assembly coming out of
the tube when pressure is applied to the cylinder.
Inner Wire Ring is pushed back
into the internal
Tube Groove
16
17. Pull the rod out to expose the external wire ring
groove in cylinder head, and then install the
external ring.
a) Extend Rod
b) Pull out Head for
Wire Ring Groove
Forward
17
c) Install External
Wire Ring
143351 - 69/7200 Series (12-May-2017)
Inner Ring
External Ring
18. Before using the cylinder, ensure that you double
check your work.
-9-
Maintenance
REPAIRING A THREADED HEAD CYLINDER
SET SCREW
STYLE
Wear
Ring
Lock
Nut
Piston
Barrel
Piston
Seal
U-Cup
Seal
Wear Ring
Gland
Rod
Assembly
DISASSEMBLY
1. Loosen Set Screw and turn off end cap.
2. Carefully remove piston/rod/gland assemblies.
3. Disassemble the piston from the rod assembly
by removing lock nut.
Set Screw
Dual Seal
Wiper
Seal
End
Cap
REPAIRING A THREADED HEAD CYLINDER
Locking
Ring Style
Lock
Nut
Piston
Piston Seals
(Style may vary,
"5 Part Seal" shown)
Wear Ring
Rod Seal
Rod Wiper Seal
DISASSEMBLY
1. Loosen Locking Ring and turn off end cap.
2. Carefully remove piston, rod and end cap.
3. Disassemble the piston from the rod assembly
by removing lock nut.
Barrel
Locking
Ring
O-Rings
Assembly
Pin Assembly
Flat Washer
Shoulder Bolt
End
Cap
Rod
NOTE: DO NOT clamp rod by chrome surface.
4. Slide off gland assembly & end cap.
5. Remove seals and inspect all parts for damage.
6. Install new seals and replace damaged parts with
new components.
7. Inspect the inside of the cylinder barrel, piston, rod
and other polished parts for burrs and scratches.
Smooth areas as needed with an emery cloth.
REASSEMBLY
1. Reinstall rod through end cap & gland assembly.
2. Secure piston to rod with lock nut. Torque lock nut
to proper value (refer to chart on previous page
for proper torque value).
3. Lube inside of barrel, piston seals, and gland seals
with hydraulic oil.
4. With cylinder body held gently in a vise, insert
piston, gland, end cap and rod combination using
a slight rocking motion.
5. Apply loctite anti-seize before installing cylinder
end cap.
6. Torque cylinder end cap to 440 lb.ft (600 N.m).
NOTE: DO NOT clamp rod by chrome surface.
4. Slide off end cap.
5. Remove seals and inspect all parts for damage.
6. Install new seals and replace damaged parts with
new components.
7. Inspect the inside of the cylinder barrel, piston, rod
and other polished parts for burrs and scratches.
Smooth areas as needed with an emery cloth.
REASSEMBLY
1. Reinstall rod through end cap.
2. Secure piston to rod with lock nut. Torque lock nut
to proper value (refer to chart on previous page
for proper torque value).
3. Thread lock ring fully onto barrel.
4. Lube inside of barrel and piston seals with
hydraulic oil.
5. With cylinder body held gently in a vise, insert
piston, end cap and rod combination using a
slight rocking motion.
6. Turn end cap fully against lock ring then back off
end cap to align ports.
7. Tighten Set Screw on end cap to 6 lb.ft (8 N.m).
143351 - 69/7200 Series (12-May-2017)
7. Tighten Locking Ring against end cap using a
punch and hammer.
-10-
Transport & Storage
TRANSPORT SAFETY
• Read and understand ALL the information in the
Operator's Manual regarding procedures and
SAFETY when operating the machine in the field/
yard or on the road.
• Check with local authorities regarding machine
transport on public roads. Obey all applicable
laws and regulations.
• Always travel at a safe speed. Use caution when
making corners or meeting traffic.
• Make sure the SMV (Slow Moving Vehicle)
emblem and all the lights and reflectors that are
required by the local highway and transport
authorities are in place, are clean and can be
seen clearly by all overtaking and oncoming
traffic.
• Keep to the right and yield the right-of-way to
allow faster traffic to pass. Drive on the shoulder,
if permitted by law.
• Always use hazard warning flashers on tractor
when transporting, unless prohibited by law.
STORAGE
After the season's use, completely inspect all major
systems of the machine. Repair or replace any worn
or damaged components to prevent unnecessary
down time at the beginning of next season.
Since the unit can be used in extremely adverse
conditions during the season, the machine should be
carefully prepared for storage to ensure that all dirt,
mud, debris and moisture has been removed.
Follow this procedure when preparing to store:
1. Wash the entire machine thoroughly using a water
hose or pressure washer to remove all dirt, mud,
debris or residue.
2. Inspect all parts to see if anything has become
entangled in them. Remove the entangled
material.
3. Lubricate all grease fittings to remove any
moisture.
4. Inspect all hydraulic hoses, fittings, lines and
couplers. Tighten any loose fittings. Replace any
hose that is badly cut, nicked or abraded or is
separating from the crimped end of the fitting.
TRANSPORTING
Follow this procedure when preparing to transport:
1. Clear the area of bystanders, especially small
children, before converting into transport
configuration.
2. Operate the lift hydraulics to raise the blade fully
and install a certified safety chain to secure it.
3. Clean the SMV sign, lights and reflectors.
4. Maintain a safe speed. Slow down when
cornering and on rough roads.
5. Slow down and pull off to the side of the road
when meeting other traffic.
6. Use hazard flashers on tractor unless prohibited
by law.
STORAGE SAFETY
• Store unit in an area away from human activity.
• Do not permit children to play near the stored unit.
5. Touch up all paint nicks and scratches to prevent
rusting.
6. Oil the exposed rams on the hydraulic cylinder to
prevent rusting.
7. Select an area that is dry, level and free of debris.
REPLACEMENT DECALS
Decals, especially safety and reflective, should be
replaced when they become damaged or worn.
Contact your dealer.
Safety Decals
142545 Mounting Decal, Use Handle 2
142546 Remove Jack Decal 2
142386 Warning Decal, Falling Blade 2
143240 Tow Cable Routing (Optional) 2
Reflective Decals
142280 Red Reflector, 6 3/8” lg 2
142279 Amber Reflector, 3-1/4” lg 1
Product Decals
142008 Degelman Logo, 25-3/4” lg 2
142908 7200 Blade Decal 1
142907 6900 Blade Decal 1
143351 - 69/7200 Series (12-May-2017)
-11-
Troubleshooting
GENERAL TROUBLESHOOTING
SYMPTOM PROBLEM SOLUTION
Blade falls down in
transport.
Blade angle won’t
hold.
Cutting edge wearing
excessively in center
of the blade.
Cutting edge wearing
excessively at ends of
the blade.
Hydraulic angle circuit
hoses pop out of valve
stack.
Cannot Retract HQT
Cylinder Pins when
attached to tractor.
Lift cylinder hydraulic circuit not connected
correctly.
Excessive loading of dozer. Reduce amount of material pushing. Equipped with safety angle
Excessive impact on dozer. Reduce speed of impact on high load. Equipped with safety angle
High downward force of dozer in contact
with crown of road.
High downward force on ends of dozer. Run dozer tilt circuit (7200-models) in float to contour to ground.
Relief valve tank drain hose not connected
properly.
Blade not raised off the ground. Lift blade off ground. (Raising the blade off the ground removes
*Ball Valve not open. Open Ball Valve.
Trace your hoses from front to back of tractor, making sure angle
circuit connected to rear relief valve, not lift circuit.
relief valve, pressure exceeded.
relief valve, pressure exceeded.
Adjust skid shoes to prevent cutting edge contact with road
crown.
Change operation of the dozer to prevent running on crown of
road.
Change operation to prevent this type of contact.
Adjust skid shoes to prevent contact.
Ensure hydraulic tank drain hose goes directly to tank with no
internal pressure.
pressure from the HQT - ”Hydraulic Quick-Tach” pins.)
Breaking cutting
edge bolts.
Blade won’t angle or
will not come back
from full angle.
Blade not following
ground contour.
Cannot align front
bracket roller with
main frame front
quick attach lug.
Cutting edge bolts not properly torqued. Under torqued bolts allows impact to break bolts.
Torque 5/8” GR8 bolts to 225 lb-ft
Torque 3/4” GR8 bolts to 400 lb-ft
Hoses not properly coupled in valve stack. Remove and re-install hoses into valve stack.
Angle relief valve return to tank line not
properly installed.
Tilt circuit (7200-models) not allowed to
float.
Heights are not aligned. Use dozer hydraulic lift circuit to adjust main frame front lug
Over torqued bolts can fail from too much tension loading.
Change return to tank line so that no internal pressure, run direct
to tank.
Float hydraulic tilt circuit.
height.
Use jacks on side on main frame to adjust height.
143351 - 69/7200 Series (12-May-2017)
-12-
Blade Attachments
OPTIONAL BLADE ATTACHMENTS
Silage Extension
112852 - 16 ft (shown)
112851 - 14 ft
112850 - 12 ft
Silage Extension Hardware
118410 - Nut, 3/4” (8)
118509 - Lock Washer, 3/4” (8)
118516 - Flat Washer, 3/4” (16)
118047 - Bolt, 3/4”x 2-1/2” (8)
Top Extension
112168 - 16 ft (shown)
112136 - 14 ft
112135 - 12 ft
Top Extension Hardware
118410 - Nut, 3/4” ( 4 or 8)
118509 - Lock Washer, 3/4” ( 4 or 8)
118516 - Flat Washer, 3/4” ( 4 or 8)
118047 - Bolt, 3/4”x 2-1/2” ( 4 or 8)
112112 - Extension, 1’ (1)
115243 - Side Plate,
LH (shown) (1)
115242 - Side Plate,
RH (1)
12’/14’ 16’
Side Plate/Extension Hardware
118410 - Nut, 3/4” (5)
118509 - Lock Washer, 3/4” (5)
118043 - Bolt, 3/4”x 2” (5)
143351 - 69/7200 Series (12-May-2017)
-13-
Blade Components
6900 Series Dozer Blades
112362 - 16 ft
112361 - 14 ft (shown)
112360 - 12 ft
7200 Series Dozer Blades
112199 - 16 ft
112205 - 14 ft (shown)
112200 - 12 ft
Note: Some 69/7200 blade
fit-ups require the “Angle
Conversion Kit” shown.
69/7200 PIVOT PIN
112274 - Pivot Pin (1)
118048 - Bolt, 3/4” x
2-1/2” UNC GR8 (2)
118775 - Flat Washer,
3/4” F436 (4)
117414 - Lock Nut,
3/4” UNC (2)
7200 TILT COMPONENTS
112181 - Tilt Plate
Assembly (1)
117087 - Bushing (2)
COMMON COMPONENTS
118204 - Scraper
Bolt, 5/8”x 2-1/4”
UNC GR5 (ar)
Cutting Edge
5/8”x 6”
116206 - 6’ (2)
116207 - 7’ (2)
116208 - 8’ (2)
118448 - Lock Nut,
5/8”- Unitorque (ar)
806014 - Skid Shoe (2)
118901 - Pin,
Lynch 1-1/2” (2)
115402 - Pin,
3/4” (2)
Note: Some 69/7200 blade
fit-ups require the “Angle
Conversion Kit” shown.
ANGLE CONVERSION KIT COMPONENTS
118611 - Bolt, 1/2” x 2-1/4” (2)
118587 - Flat Washer, 1/2” F436 (4)
118504 - Lock Washer, 1/2” (2)
118405 - Nut, 1/2” (2)
790090 -
Jack Holder,
LH (1)
Top Holes (2) - Bolt Hardware
117558 - Bolt, 1-1/4” x 3-1/2” (4)
118445 - Lock Nut, 1-1/4” UNC GR5 (4)
Bottom Holes (2) - Bolt Hardware
118984 - Bolt, 1-1/4” x 3” (4)
131206 - Flat Washer, 1-1/4” F436 (4)
117559 - Lock Nut, 1-1/4” - thin (4)
790081 - Lug
Adapter (2)
790087 - Pin
Assembly (2)
112272 Tilt Ring (2)
118051 - Bolt,
117414 - Lock Nut,
3/4” UNC GRC (6)
790091 -
Jack Holder,
RH (1)
790089 -
Spacer (1)
3/4” x 3”
UNC GR8 (6)
Located on
bottom plate.
143351 - 69/7200 Series (12-May-2017)
-14-
Pivot & Main Frame
PIVOT & MAIN FRAME OVERVIEW
PIVOT & MAIN FRAME COMPONENTS
123082 - Cylinder, 4-1/2 x 20 x 2 (2)
Previously: 123470 - Cylinder (2)
117145 -
Bushing (2)
117413 - Bolt, 5/16
x 3-3/4 (2)
780333 - Clamp
Block Plate (4)
780332 - Hose
Clamp Block (6)
118121 - Bolt,
5/16 x 2 (2)
791200 - Main Frame
790730 - Pivot
Frame Assembly (1)
Assembly (1)
790022 - Angle Pin,
1-1/2 x 5-1/2 (2)
117145 - Bushing (2)
118611 - Bolt, 1/2 x 2-1/4 (2)
118587 - Flat Washer, 1/2
SAE F436 (4)
118504 - Lock Washer, 1/2 (2)
118405 - Nut, 1/2 (2)
132051 -Sidewind
Jack (2)
143351 - 69/7200 Series (12-May-2017)
789580 - Pivot Pin,
pivot/main (2)
118514 - Flat Washer, 5/8 F436 (2)
118508 - Lock Washer, 5/8 (2)
118645 - Bolt, 5/8 x 1-1/4 (2)
-15-
Mounting Brackets - Single Reduction (SR)
UNDER CARRIAGE BRACKET LOCATIONS
SINGLE REDUCTION (SR)
AXLE MODELS
If installed, remove Toolbox (Front
Left), Tow Cable Attachment Bracket
(Front Right), and Front Weight Stack
Components mounting bracket.
IMPORTANT-TORQUE
Torque all bolts properly!
Refer to maintenance section
for torque specifications.
IMPORTANT
NO GAPS!
* Use Shims
only as required to
ensure “No-Gap”
between the tractor
axle & frame and
the new bracket.
SINGLE REDUCTION (SR)
Non-Slotted Axle Mount
791295 - Nut Retainer, Rear-RH (1)
791296 - Nut Retainer, Rear-LH (1)
791293 - Nut Retainer, Front (2)
118749 - Flat Washer,
M20 - SAE (20)
(LH side)
117553 Bolt, M20 x
2.5 x 70 (5)
HQT CYLINDER
DETAIL
123059 - Cylinder,
HQT - 2 x 4.59 x
1-1/4, double (1)
(Previously: 122340)
122345 - HQT
Pin, 2-1/2 x
5-5/8” (2)
118750 - Lock Nut,
M20 x 2.5 (10)
791290 - HQT Cylinder
791285 - Hyd Multi-
Coupler Brkt (1)
118643- Bolt,
1/2 x 4 GR8 (2)
118504 - Lock
Washer, 1/2 (2)
118537 - Flat Washer, 5/8 F436 (6)
118448 - Lock Nut, 5/8 GRB Unitorq (3)
791252 - U/C
Bracket Assembly,
RH (1)
Bracket (1)
791251 - U/C
Bracket Assembly,
LH (1)
(Note:
Apply Blue Loctite
242 to HQT Pin Bolt
threads when installing)
118028 - Bolt, 5/8 x 2-1/2 (3)
118749 - Flat Washer, M20 - SAE (10)
117553 - Bolt, M20 x 2.5 x 70 (10)
118751 - Bolt, M20 x 2.5 x 60 (5)
(RH
side)
(See HQT
Cylinder Detail)
791247 - Rear
X-Member (1)
*791248 - Shim, 3 hole (8)
118777 - Flat Washer, M24 (12)
117592 - Bolt, M24 x 3
x 60 P10.9 (12)
*791262 - Shim, 4 hole (4)
(Non-Slotted
Mount)
791298 -
Bolt Plate (2)
117416 - Lock Nut, 7/8
GRC Unitorque (4)
117416 - Lock Nut, 7/8 - Unitorque (16)
118774 - Flat Washer, 7/8 F436 (16)
117482 - Scraper Bolt, 7/8 x 3 (16)
117595 - Jam Nut, 1 UNF GR8 (8)
117594 - Bolt, 1 x 3 UNF GR8 (8)
Previous
Components
117416 -
Lock Nut, 7/8
GRC Unitorque (4)
(Both sides)
* Use shims
only as
required
to ensure
“No-Gap”
between
tractor axle
and new
bracket.
118777 - Flat
Washer, M24 (8)
117593 - Bolt,
M24 x 3 x 140
P8.8 (8)
(Same as other
location)
117474 - Bolt,
7/8 x 4 GR8 (4)
118774 - Flat
Washer, 7/8
118768 - Bolt, 7/8
x 3-1/2 GR8 (4)
118774 - Flat
Washer, 7/8
F436 (8)
F436 (8)
143351 - 69/7200 Series (12-May-2017)
-16-
Mounting Brackets - Single Reduction (SR)
UNDER CARRIAGE BRACKET LOCATIONS
SINGLE REDUCTION (SR)
AXLE MODELS
If installed, remove Toolbox (Front
Left), Tow Cable Attachment Bracket
(Front Right), and Front Weight Stack
Components mounting bracket.
IMPORTANT-TORQUE
Torque all bolts properly!
Refer to maintenance section
for torque specifications.
SINGLE REDUCTION (SR)
Slotted Axle Mount
791295 - Nut Retainer, Rear-RH (1)
791296 - Nut Retainer, Rear-LH (1)
791293 - Nut Retainer, Front (2)
118749 - Flat Washer,
M20 - SAE (20)
(LH side)
117553 Bolt, M20 x
2.5 x 70 (5)
HQT CYLINDER
DETAIL
123059 - Cylinder,
HQT - 2 x 4.59 x
1-1/4, double (1)
122345 - HQT
Pin, 2-1/2 x
5-5/8” (2)
118750 - Lock Nut,
M20 x 2.5 (10)
791285 - Hyd Multi-
Coupler Brkt (1)
118643- Bolt,
1/2 x 4 GR8 (2)
118504 - Lock
Washer, 1/2 (2)
118448 - Lock Nut, 5/8 GRB Unitorq (3)
791252 - U/C
Bracket Assembly,
RH (1)
791290 - HQT Cylinder
Bracket (1)
791251 - U/C
Bracket Assembly,
(Note:
Apply Blue Loctite
242 to HQT Pin Bolt
threads when installing)
118028 - Bolt, 5/8 x 2-1/2 (3)
118537 - Flat Washer, 5/8 F436 (6)
118749 - Flat Washer, M20 - SAE (10)
117553 - Bolt, M20 x 2.5 x 70 (10)
118751 - Bolt, M20 x 2.5 x 60 (5)
(RH
side)
(Slotted
Mount)
(See HQT
Cylinder Detail)
791247 - Rear
X-Member (1)
LH (1)
117416 - Lock Nut, 7/8 - Unitorque (16)
118774 - Flat Washer, 7/8 F436 (16)
117482 - Scraper Bolt, 7/8 x 3 (16)
IMPORTANT
NO GAPS!
* Use Shims
only as required to
ensure “No-Gap”
between the tractor
axle & frame and
the new bracket.
(Both sides)
*791248 - Shim, 3 hole (8)
791265 - Washer, 3 Hole (4)
117202 - SHCS, M24
x 3 x 80 P10.9 (12)
*791262 - Shim, 4 hole (4)
118777 - Flat
Washer, M24 (8)
117593 - Bolt, M24
791298 Bolt Plate (2)
117416 - Lock Nut, 7/8
GRC Unitorque (4)
117595 - Jam Nut, 1 UNF GR8 (8)
117594 - Bolt, 1 x 3 UNF GR8 (8)
* Use shims
only as
required
to ensure
“No-Gap”
between
tractor axle
and new
bracket.
Torque: 620 lb.ft
(840 N.m)
x 3 x 140
P8.8 (8)
(Same as other
location)
117474 - Bolt,
7/8 x 4 GR8 (4)
118774 - Flat
Washer, 7/8
F436 (8)
143351 - 69/7200 Series (12-May-2017)
-17-
Mounting Brackets - HydraCushion Suspension (HC)
UNDER CARRIAGE BRACKET LOCATIONS
DOUBLE REDUCTION AXLE
MODELS with HydraCushion™
Suspension (HC)
If installed, remove Toolbox (Front Left), Tow
Cable Attachment Bracket (Front Right), and
Front Weight Stack Components mounting
bracket.
IMPORTANT-TORQUE
Torque all bolts properly!
Refer to maintenance section
for torque specifications.
IMPORTANT
NO GAPS!
* Use Shims
only as required to
ensure “No-Gap”
between the tractor
axle & frame and
the new bracket.
HydraCushion™ Suspension (HC)
DOUBLE REDUCTION AXLE
Non-Slotted Axle Mount
791295 - Nut Retainer, Rear-RH (1)
791296 - Nut Retainer, Rear-LH (1)
791293 - Nut Retainer, Front (2)
118749 - Flat Washer,
M20 - SAE (20)
(LH side)
117553 Bolt, M20 x
2.5 x 70 (5)
HQT CYLINDER
DETAIL
123059 - Cylinder,
HQT - 2 x 4.59 x
1-1/4, double (1)
(Previously: 122340)
122345 - HQT
Pin, 2-1/2 x
5-5/8” (2)
118750 - Lock Nut,
M20 x 2.5 (10)
791290 - HQT Cylinder
791285 - Hyd Multi-
Coupler Brkt (1)
791271 - U/C Bracket
118643- Bolt,
1/2 x 4 GR8 (2)
118504 - Lock
Washer, 1/2 (2)
118028 - Bolt, 5/8 x 2-1/2 (3)
118537 - Flat Washer, 5/8 F436 (6)
118448 - Lock Nut, 5/8 GRB Unitorq (3)
791272 - U/C
Bracket Assembly,
RH (1)
Bracket (1)
Assembly, LH (1)
(Note:
Apply Blue Loctite
242 to HQT Pin Bolt
threads when installing)
118749 - Flat Washer, M20 - SAE (10)
117553 - Bolt, M20 x 2.5 x 70 (10)
118751 - Bolt, M20 x 2.5 x 60 (5)
*791281 - Shim, 2 hole (4)
118777 - Flat Washer,
117592 - Bolt,
M24 x 3 x 60 (4)
*791248 - Shim,
3 hole (4)
(Non-Slotted
Mount)
(See HQT
Cylinder Detail)
791247 - Rear
X-Member (1)
791298 -
Bolt Plate (2)
117416 - Lock Nut, 7/8
GRC Unitorque (4)
117416 - Lock Nut, 7/8 - Unitorque (16)
118774 - Flat Washer, 7/8 F436 (16)
117482 - Scraper Bolt, 7/8 x 3 (16)
117595 - Jam Nut, 1 UNF GR8 (8)
117594 - Bolt, 1 x 3 UNF GR8 (8)
Previous
Components
117416 -
Lock Nut, 7/8
GRC Unitorque (4)
(Both sides)
M24 (4)
(RH side)
* Use shims
only as
required
to ensure
“No-Gap”
between
tractor axle
and new
bracket.
118777 - Flat
Washer, M24 (6)
117592 - Bolt,
M24 x 3 x 60 (6)
117474 - Bolt,
7/8 x 4 GR8 (4)
118774 - Flat
Washer, 7/8
F436 (8)
118768 - Bolt, 7/8
x 3-1/2 GR8 (4)
118774 - Flat
Washer, 7/8
F436 (8)
143351 - 69/7200 Series (12-May-2017)
-18-
Mounting Brackets - HydraCushion Suspension (HC)
UNDER CARRIAGE BRACKET LOCATIONS
DOUBLE REDUCTION AXLE
MODELS with HydraCushion™
Suspension (HC)
If installed, remove Toolbox (Front Left), Tow
Cable Attachment Bracket (Front Right), and
Front Weight Stack Components mounting
bracket.
IMPORTANT-TORQUE
Torque all bolts properly!
Refer to maintenance section
for torque specifications.
IMPORTANT
NO GAPS!
* Use Shims
only as required to
ensure “No-Gap”
between the tractor
axle & frame and
the new bracket.
HydraCushion™ Suspension (HC)
DOUBLE REDUCTION AXLE
Slotted Axle Mount
791295 - Nut Retainer, Rear-RH (1)
791296 - Nut Retainer, Rear-LH (1)
791293 - Nut Retainer, Front (2)
118749 - Flat Washer,
M20 - SAE (20)
(LH side)
117553 Bolt, M20 x
2.5 x 70 (5)
HQT CYLINDER
DETAIL
123059 - Cylinder,
HQT - 2 x 4.59 x
1-1/4, double (1)
(Previously: 122340)
122345 - HQT
Pin, 2-1/2 x
5-5/8” (2)
118750 - Lock Nut,
M20 x 2.5 (10)
791290 - HQT Cylinder
791285 - Hyd Multi-
Coupler Brkt (1)
791271 - U/C Bracket
118643- Bolt,
1/2 x 4 GR8 (2)
118504 - Lock
Washer, 1/2 (2)
118028 - Bolt, 5/8 x 2-1/2 (3)
118537 - Flat Washer, 5/8 F436 (6)
118448 - Lock Nut, 5/8 GRB Unitorq (3)
791272 - U/C
Bracket Assembly,
RH (1)
Bracket (1)
Assembly, LH (1)
(Note:
Apply Blue Loctite
242 to HQT Pin Bolt
threads when installing)
118749 - Flat Washer, M20 - SAE (10)
117553 - Bolt, M20 x 2.5 x 70 (10)
118751 - Bolt, M20 x 2.5 x 60 (5)
*791281 - Shim, 2 hole (4)
791266 - Washer, 2 Hole (4)
117202 - SHCS, M24
x 3 x 80 P10.9 (4)
Torque: 620 lb.ft (840 N.m)
791265 - Washer,
3 Hole (2)
*791248 - Shim,
3 hole (4)
Slotted
Mount)
(See HQT
Cylinder Detail)
791247 - Rear
X-Member (1)
791298 -
Bolt Plate (2)
117416 - Lock Nut, 7/8
GRC Unitorque (4)
117416 - Lock Nut, 7/8 - Unitorque (16)
118774 - Flat Washer, 7/8 F436 (16)
117482 - Scraper Bolt, 7/8 x 3 (16)
117595 - Jam Nut, 1 UNF GR8 (8)
117594 - Bolt, 1 x 3 UNF GR8 (8)
(Both sides)
(RH side)
* Use shims
only as
required
to ensure
“No-Gap”
between
tractor axle
and new
bracket.
117202 - SHCS,
M24 x 3 x 80 (6)
Torque: 620 lb.ft
117474 - Bolt,
7/8 x 4 GR8 (4)
118774 - Flat
Washer, 7/8
(840 N.m)
F436 (8)
143351 - 69/7200 Series (12-May-2017)
-19-
Mounting Brackets - Double Reduction (DR)
UNDER CARRIAGE BRACKET LOCATIONS
DOUBLE REDUCTION (DR)
AXLE MODELS
(without HydraCushion™)
If installed, remove Toolbox (Front
Left), Tow Cable Attachment Bracket
(Front Right), and Front Weight Stack
Components mounting bracket.
IMPORTANT-TORQUE
Torque all bolts properly!
Refer to maintenance section
for torque specifications.
IMPORTANT
NO GAPS!
* Use Shims
only as required to
ensure “No-Gap”
between the tractor
axle & frame and
the new bracket.
791295 - Nut Retainer, Rear-RH (1)
791296 - Nut Retainer, Rear-LH (1)
(LH side)
117553 Bolt, M20 x
2.5 x 70 (5)
HQT CYLINDER
DETAIL
123059 - Cylinder,
HQT - 2 x 4.59 x
1-1/4, double (1)
(Previously: 122340)
122345 - HQT
Pin, 2-1/2 x
5-5/8” (2)
Bracket Assembly,
791293 - Nut Retainer, Front (2)
118749 - Flat Washer,
M20 - SAE (20)
118750 - Lock Nut,
M20 x 2.5 (10)
791290 - HQT Cylinder
Bracket (1)
791285 - Hyd Multi-
Coupler Brkt (1)
791221 - U/C Bracket
118643- Bolt,
1/2 x 4 GR8 (2)
118504 - Lock
Washer, 1/2 (2)
(Note:
Apply Blue Loctite
242 to HQT Pin Bolt
threads when installing)
118028 - Bolt, 5/8 x 2-1/2 (3)
118537 - Flat Washer, 5/8 F436 (6)
118448 - Lock Nut, 5/8 GRB Unitorq (3)
791222 - U/C
RH (1)
Assembly, LH (1)
118749 - Flat Washer, M20 - SAE (10)
117553 - Bolt, M20 x 2.5 x 70 (10)
118751 - Bolt, M20
(See HQT
Cylinder Detail)
791247 - Rear
X-Member (1)
117416 - Lock Nut, 7/8 - Unitorque (16)
118774 - Flat Washer, 7/8 F436 (16)
117482 - Scraper Bolt, 7/8 x 3 (16)
x 2.5 x 60 (5)
*791248 - Shim, 3 hole (8)
117416 - Lock Nut, 7/8
117595 - Jam Nut, 1 UNF GR8 (8)
117594 - Bolt, 1 x 3 UNF GR8 (8)
(RH side)
118777 - Flat Washer,
M24 (6)
117591 - Bolt, M24
x 3 x 120 (6)
*791249 - Shim,
2 hole (4)
791298 -
Bolt Plate (2)
GRC Unitorque (4)
Previous
Components
117416 -
Lock Nut, 7/8
GRC Unitorque (4)
(Both sides)
* Use shims
only as
required
to ensure
“No-Gap”
between
tractor axle
and new
bracket.
118777 - Flat
Washer, M24 (4)
117591 - Bolt, M24
x 3 x 120 (4)
117474 - Bolt,
7/8 x 4 GR8 (4)
118774 - Flat
Washer, 7/8
F436 (8)
118768 - Bolt, 7/8
x 3-1/2 GR8 (4)
118774 - Flat
Washer, 7/8
F436 (8)
143351 - 69/7200 Series (12-May-2017)
-20-
Mounting Brackets
OPTIONAL KITS
TOOLBOX, TOW CABLE, &
EURO LIGHT RELOCATION KITS
- Front tractor bumper (R296504) needs
to be removed prior to installation of the
“Tow Cable Relocation Kit”.
- The “Toolbox or Euro Light Relocation
Kits” do not require removal of the front
bumper, but it could aid in installation.
791340 - Tow Cable
Relocation Kit (1)
791335 - Tow Cable Bracket Assembly (1)
comes with...
118816 - Pin, KLIK - 7/16 (2)
118552 - Flat Wash-
791339 - Pin, 1-1/2 x 7-5/8 (1)
118447 - Lock Nut, 5/8 GRC Unitorque (2)
118537 - Flat Washer, 5/8 - F436 (4)
118027 - Bolt, 5/8 x 2 - GR8 (2)
er, 1-1/2 SAE (2)
791347 - Toolbox Relocation Kit (1)
Re-use existing toolbox mounting bracket &
hardware. Use holes shown to center bracket.
Located by hood latch base, remove/
replace existing hardware with new...
117596 - Bolt, M8 x 90 - P8.8 (2)
791342 - Toolbox Bracket
Assembly (1)
117598 - Flat Washer, M8 (4)
117597 - Lock Nut, M8 - CL8 (2)
791349 - Euro Light Relocation Kit (1)
...with integrated toolbox relocation mount
Re-use existing
mounting
hardware...
Toolbox (if applicable) can also be
relocated by re-using existing toolbox
mounting hardware (See above)......
143351 - 69/7200 Series (12-May-2017)
Located by hood latch base,
remove/replace existing
hardware with new...
117596 - Bolt, M8 x
100 - P8.8 (2)
117598 - Flat Washer, M8 (4)
791345 - Euro Light Bar
Bracket Assembly (1)
117597 - Lock Nut, M8 - CL8 (2)
-21-
Cylinders
TILT CYLINDERS
123196 - Cylinder, 4” x 8” x 2”
123079 - Seal Kit
123238 - Pin, Kit - includes
118930 - Pin, 1” x 2-13/16” (2)
118924 - Flat washer, .59” ID x .9” OD (2)
118796 - Shoulder bolt, 1/2” GR8 UNC (2)
LIFT CYLINDERS
123082 - Cylinder, 4-1/2” x 20” x 2”
123083 - Seal Kit
PREVIOUS: 122734 - Cylinder, 4” x 8” x 2”
118946 - Lock nut,
1-1/4” UNF GR5
unitorque (1)
122774 - Piston (1)
122775 - Rod & Clevis (1)
122785 - Seal Kit (1)
PREVIOUS: 123470 - Cylinder, 4-1/2” x 20” x 2”
118946 - Lock nut,
1-1/4” UNF GR5
unitorque (1)
123480 - Piston (1)
118930 - Pin, 1” x 2-13/16” (2)
118924 - Flat washer, .59” ID x .9” OD (2)
118796 - Shoulder bolt, 1/2” GR8 UNC (2)
121796 - Barrel (1)
122783 - Lock Ring (1)
122781 - Open Cap (1)
123472 - Barrel (1)
123479 - Lock Ring (1)
123477 - Open Cap (1)
123236 - Pin, Kit - includes
122670 - Pin, 1-1/2” x 2-3/4” (2)
118924 - Flat washer, .59” ID x .9” OD (2)
118796 - Shoulder bolt, 1/2” GR8 UNC (2)
ANGLE CYLINDERS
123080 - Cylinder, 4” x 40-1/2” x 2-1/2”
123081 - Seal Kit
HYDRAULIC QUICK-TACH CYLINDER
123059 - Cylinder, 2” x 4-19/32” x 1-1/4”
(Internal Rod Thread)
123484 - Seal Kit (1)
118796 - Shoulder bolt, 1/2” GR8 UNC (2)
118924 - Flat washer, .59” ID x .9” OD (2)
PREVIOUS: 122980 - Cylinder, 4” x 40-1/2” x 2-1/2”
122922 - Barrel (1)
118946 - Lock nut, 1-1/4”
UNF GR5 unitorque (1)
122974 - Piston, Unitised (1)
122962 - Rod & Ball (1)
122978 - Seal Kit (1)
PREVIOUS: 122340 - Cylinder, 2” x 4-19/32” x 1-1/4”
(Internal Rod Thread)
122966 - Open Cap (1)
122506 - Open Cap (2)
122508 - Lock Ring (2)
122305 - Rod &
Clevis (1)
122670 - Pin, 1-1/2”
x 2-3/4” (2)
122783 - Lock
Ring (1)
123060 - Seal Kit
143351 - 69/7200 Series (12-May-2017)
-22-
118441 - Lock nut,
7/8” UNF unitorque (2)
122513 - Piston (2)
122521 - Seal Kit (2)
122342 - Barrel (1)
122344 - Rod (2)
Hydraulic Routing
HYDRAULIC & COUPLER MOUNTING BRACKETS
141674 - Flush Face Quick
Coupler-m (4 or 6)
141618 - Nipple,
3/4 JIC-m x 1-1/16
ORB (4 or 6)
118718 - Lock Nut, 5/16 (4)
118731 - Flat Washer, 5/16 (8)
118110 - Bolt, 5/16 x 1 (4)
789722 - Hydraulic Coupler
Bracket (1)
141675 - Flush Face
Quick Coupler-f (4 or 6)
117545 - Jam
Nut 3/4 (4 or 6)
117546 - Star
118718 - Lock Nut, 5/16 (4)
Washer (4 or 6)
118731 - Flat Washer, 5/16 (4)
117489 - U Bolt, 5/16 (2)
141504 - 90° Elbow,
3/4 JIC-m x ORB (1)
141518 - 90° Elbow,
3/4 JIC-m x JIC-f (1)
141515 - Nipple,
3/4 JIC-m x ORB (1)
141597 - Ball
Valve, 3/4 ORB (1)
COMMON HYDRAULIC FITTINGS
This is a quick visual reference of the most common hydraulic fittings for Dozer Blade / PileDriver hydraulic systems. The icon and numbers
are used for reference in the routing diagrams on the following pages. Some fitting types shown may not be used on your particular fit-up.
141504 - 90° Elbow,
3/4 m JIC x ORB
8 9
2 3 4
141527 - Tee, 3/4 JIC-m
x JIC-m x ORB
3/4 JIC-m x JIC-f
10
141581 - Quick
Coupler-m - 3/4 ORB
11
141515 - Nipple, 3/4
JIC-m x ORB
12
61 5
141505 - Tee, 3/4
JIC-m x ORB x JIC-m
13
7
141501- Tee, 3/4 JIC-m141518 - 90° Elbow,
14
15
141513 - 90° Elbow,
3/4 JIC-m
16
141577 - Dust Cap
Coupler-m
23
141597 - Ball
Valve, 3/4 ORB
141616 - 45° Elbow
3/4 JIC-m x ORB
17
141578 - Dust Plug
Coupler-f
24
141574 - Relief Valve
143351 - 69/7200 Series (12-May-2017)
141620 - 45° Elbow
3/4 JIC-m x f-sw
141560 - 90° Elbow,
3/4 JIC-m x 9/16 ORB
25
26
248385 - Plug,
Kinecor
141618 - Nipple, 3/4
JIC x 1-1/16 ORB
1918
141561 - Nipple, 3/4
JIC-m x 9/16 ORB
141119 - Relief Valve
-23-
141674 - Flush Face
Quick Coupler -m
20
141573 - Flush Face
Coupler, 3/4 ORB
141672 - Nipple, 1/2 SAE
141671 - Coupler, 1/2 SAE
141675 - Flush Face
Quick Coupler -f
21
126675 - Hose 3/8 x 5-5/8 2WB 3/4 JIC F-SW W/EL
27
141588 - Quick Coupler Unit (1)
117546 - Star Washer
117545 - Jam Nut 3/4
22
141506 - Orifice
Plate - 0.07” ID
Hydraulic Routing
TILT CYLINDER ROUTING
123196 - Cylinder, 4 x 8 x 2 (2)
Previously: 122734 - Cylinder (2)
25
126690 - Hose, 1/2 x 25 (2)
169
126572 - Hose, 1/2 x 169 (2)
1
2
3
141504 - 90° Elbow, 3/4 JIC-m x ORB (2)
141527 - Tee, 3/4 JIC-m x JIC-m x ORB (2)
141518 - 90° Elbow, 3/4 JIC-m x JIC-f (2)
LIFT CYLINDER ROUTING
123082 - Cylinder, 4-1/2 x 20 x 2 (2)
Previously: 123470 - Cylinder (2)
75
126566 - Hose, 1/2 x 75 (1)
86
126598 - Hose, 1/2 x 86 (1)
100
126603 - Hose, 1/2 x 100 (1)
130
126694 - Hose, 1/2 x 130 (1)
1
141504 - 90° Elbow, 3/4 JIC-m x ORB (2)
2
141527 - Tee, 3/4 JIC-m x JIC-m x ORB (2)
3
141518 - 90° Elbow, 3/4 JIC-m x JIC-f (2)
7200 Models Only
25
2
25
3
169
169
Refer to Front Hydraulic
Connection Detail for
connection options.
86
32
130
32
100
75
Refer to Front Hydraulic
Connection Detail for
connection options.
2
11
3
1
Ports
1
Face Up
ANGLE CYLINDER ROUTING
123080 - Cylinder, 4 x 40-1/2 x 2-1/2 (2)
Previously: 122980 - Cylinder (2)
70
126693 - Hose, 1/2 x 70 (2)
75
126566 - Hose, 1/2 x 75 (2)
140
126599 - Hose, 1/2 x 140 (2)
1
3
5
6
7
21
22
141504 - 90° Elbow, 3/4 JIC-m x ORB (2) (4)
141518 - 90° Elbow, 3/4 JIC-m x JIC-f (2)
141515 - Connector, 3/4 JIC-m x ORB (2)
141505 - Tee, 3/4 JIC-m x ORB x JIC-m (2)
141501- Tee, 3/4 JIC-m (2)
126675 - Hose, 3/8 x 5-5/8 - 2WB
3/4 JIC F-SW W/EL (2)
141506 - Orifice Plate, 0.07” ID (2)
Use inner lug holes
7
75
1
22
21
6
75
70
140
140
5
Previous
1
Refer to Front Hydraulic
Connection Detail for
connection options.
7
3
70
3
22
1
21
6
Ports
Face Up
5
Previous
1
6
1
22
21
143351 - 69/7200 Series (12-May-2017)
-24-
Hydraulic Routing
FRONT HYDRAULIC CONNECTION DETAIL
Front
311
311
264
Front of
311
311
264
From Front Cylinders
From Angle Cylinders
From Lift Cylinders
From Tilt Cylinders
141618 - Nipple, 3/4 JIC-m
x 1-1/16 ORB (4 or 6)
141674 - Flush Face Quick
Coupler-m (4 or 6)
141675 - Flush Face Quick
Coupler-f (4 or 6)
789722 - Hydraulic
Coupler Mount
117546 - Star Washer (4 or 6)
117545 - Jam Nut 3/4 (4 or 6)
140
75
169 169
140
100
11
12
Lift Cylinders
Tilt Cylinders
Angle Cylinders
Hoses from
front cylinders
are wrapped
together in a
large protective
hose wrap.
LH Side
Bracket
13
14
15
To Rear Connection
*Hose wrap is supplied
for High Wear areas.
Tractor
BALL VALVE ROUTING
75
126566 - Hose, 1/2 x 75 (1)
311
126610 - Hose, 1/2 x 311 (1)
141515 - Connector,
3/4 JIC-m x ORB (1)
141597 - Ball Valve,
3/4 ORB (1)
141504 - 90° Elbow,
3/4 JIC-m x ORB (1)
141518 - 90° Elbow,
3/4 JIC-m x JIC-f (1)
1
3
5
311
75
From Rear
Connection
To HQT
Cylinder
HQT (HYDRAULIC QUICK-TACH) ROUTING
123059 - Cylinder, 2” x 4-19/32” x 1-1/4” - Internal Rod Thread
Previously: 122340 - Cylinder - Internal Rod Thread
9
126578 - Hose, 3/8 x 9 (2)
311
126610 - Hose, 1/2 x 311 (1)
To Rear Hydraulic
141501- Tee, 3/4 JIC-m (1)
141561 - Connector, 3/4
JIC-m x 9/16 ORB (1)
141560 - 90° Elbow, 3/4
JIC-m x 9/16 ORB (2)
Connection
9
18
From Ball Valve
Connection
311
75
7
9
19
18
REAR HYDRAULIC ANGLE
RELIEF VALVE & COMPONENTS
Mounts to existing
threaded bosses
117413 - Bolt, 5/16
x 3-3/4 (2)
791288 - Relief Bracket (1)
141616 - 45° Elbow
3/4 JIC-m x ORB (2)
141574 - Relief Valve (1)
118538 - Flat Washer, 5/16 (2)
118530 - Lock Washer, 5/16 (2)
118427 - Nut, 5/16 (2)
141504 - 90º Elbow, 3/4 m JIC x ORB (3)
117464 - Lock
Washer, M10 (2)
117463 - Bolt,
M10 x 1.5 x 20
P8.8 (2)
143351 - 69/7200 Series (12-May-2017)
-25-
Hydraulic Routing
REAR HOSE ROUTING
52
126597 - Hose, 1/2 x 52 (3)
264
126513 - Hose, 1/2 x 264 (2)
311
126610 - Hose, 1/2 x 311 (2 or 4)
1
4
9
16
20
24
141504 - 90° Elbow, 3/4 JIC-m x ORB (10 or 12)
141581 - Quick Coupler-m, 3/4 ORB (6 or 8)
141616 - 45° Elbow, 3/4 JIC-m x ORB (2)
141577 - Dust Cap, Coupler-m (6 or 8)
141573 - Flush Face Coupler, 3/4 ORB (1)
141574 - Relief Valve (1)
RELIEF VALVE CONNECTION DETAIL
IMPORTANT
MUST be used on Angle Hydraulic System
Alternate drain, some
models only (see below)
Connects to
hydraulic
tank drain.
IMPORTANT
MUST be zero pressure
in return line.
1 4 16
24
264
1
9
264
1
140
20
1
52
52
52
Note: 7200 Models require
extra hoses for Tilt System.
IMPORTANT
system/tank drain and then to rear
Refer to Front Hydraulic
Connection Details
9 9
75
311
311
264
311
311
264
311
311
Run hoses down one side
then cross over at the joint.
Ensure there is enough
slack for turning.
264
1
140
24
ANGLE SYSTEM ONLY
MUST connect to rear relief valve
hydraulic connections - see detail.
264
Alternate drain,
some models only
(see below)
IMPORTANT:
Secure the hoses
so they do not
rub the driveline
or wear on any
other surfaces.
311
311
311
TILT, LIFT & HQT
311
SYSTEMS ONLY
311
to rear hydraulic
311
1 4 16
Connect direct
connections.
MUST connect
to rear tractor
hydraulic connections.
*ALTERNATE DRAIN
Remove existing tractor plug
Models without a motor seal drain
kit (SR: BRE10112 or DR & HC:
BRE10113) require a drain line
routed to the hydraulic tank.
Remove existing plug, install nipple
and attach hose (140) routed from
rear relief valve.
Install new nipple (141677)
Requires:
126599 - Hose, 1/2 x 140 (1)
141677 - Nipple, 3/4 JIC-m x M18M STR (1)
IMPORTANT
Connect to hydraulic tank drain.
(sample image only: actual tractor
location and arrangement may differ)
143351 - 69/7200 Series (12-May-2017)
-26-
Mounting
HYDRAULIC QUICK-TACH
Please note: The brackets and frame
assembly for your particular fit-up may
differ significantly from those used in the
diagram, however, the basic mounting
procedure should remain the same.
(Refer to the “10 STEP MOUNTING”
procedure and diagram below)
10
STEPSTEP
Mounting
Extend Lift
Cylinders
4
1
1
Hydraulics
3
Level
Open
Tow Cable
Side Bracket
Pin
Ball Valve
2
2
HQT
Cylinder Pin
10 STEP MOUNTING PROCEDURE
Procedure to mount blade:
1. Align the tractor behind the main frame.
(Unhook & lower front Tow Cable - if applicable)
2. Open the HQT (Hydraulic Quick-Tach) circuit ball
valve. Check and ensure HQT Cylinder pins are
retracted.
3. Drive forward close enough to connect the hydraulics.
Hook up the hydraulics.
4. Extend the lift cylinders fully.
5. Jack up frame until the main frame hooks are lifted up
level with the side bracket roller pins.
6. Drive forward to engage the side bracket pins.
7. Lower main frame hooks onto side bracket pins with
jacks until the jack base(s) are approximately 4” to 6”
off the ground.
8. Retract the lift cylinders bringing the rear main frame
connection into position. (By retracting the lift cylinder,
the weight of the front of the blade swings the back
frame upward, positioning the HQT Cylinder pins)
9. Activate the HQT Cylinder and ensure both axle pins
are engaged and fully secured.
10. Remove frame jacks and place in their storage
IMPORTANT: Close the ball valve to prevent
accidental operation of this circuit.
positions on back of blade. (Re-attach front Tow Cable
on front bracket hook - if applicable)
Jack
5
6
7
Ball Valve
Retract Lift
Cylinders
8
10
Close
9
Important:
There should be a
small gap (3/8”-1/2”)
between the inside of
the Hook to the front
of the Roller Pin.
Main Frame Hook
Side Bracket
Pin
Main Frame Hook
Hook
9
HQT
Cylinder Pin
3/8 - 1/2 gap
Side Bracket
Pin
UNHOOKING - REMOVING BLADE
DANGER
retract the lift cylinders to lift blade before disengaging the
HQT (Hydraulic Quick-Tach) cylinder pins! This transfers
the weight to the main frame hooks from the rear axle.
Otherwise, the whole assembly may come crashing down.
Procedure to remove blade:
1. Retract lift cylinder to lift blade.
2. Open the HQT circuit Ball Valve. Activate the HQT
Cylinder to Fully Retract both HQT pins.
3. Lower blade by extending the lift cylinders.
(Main frame will disengage from axle bracket)
4. Install frame jacks. Raise jack to fully support frame.
Roller pins should be raised slightly from hooks in
order to back out.
5. Close Ball Valve, disconnect Hydraulics and front
Tow Cable (if applicable). Check that connection
points are disconnected and clear to back out.
6. Back tractor out. (Re-attach tow cable - if applicable)
IMPORTANT: You must
143351 - 69/7200 Series (12-May-2017)
-27-
Warranty
2 Year
Limited Warranty
Degelman Industries Ltd. (“Degelman”) warrants to the original purchaser of any new Degelman equipment, purchased
from an authorized Degelman dealer, that the equipment will be free from defects in material and workmanship for a
period of two (2) years from the date of delivery, for non-commercial use (including farm, institutional, government, and
municipality) and (1) year from the date of delivery for commercial use. The obligation of Degelman to the purchaser
under this warranty is limited to the repair or replacement of defective parts in the first year and to the provision, but not
the installation of replacement parts in the second year. Degelman reserves the right to inspect any equipment or parts
which are claimed to have been defective in material or workmanship.
This warranty limits its replacement or repair coverage to what is consistent with the warranty of Degelman’s suppliers of
purchased components. Replacement or repair parts installed in the equipment covered by this limited warranty are
warranted for ninety (90) days from the date of delivery of such part or the expiration of the applicable new equipment
warranty period, which ever occurs later. Warranted parts shall be provided at no cost to the user at an authorized
Degelman dealer during regular working hours. Warranted replacement parts will either be replaced or rebuilt at
Degelman’s discretion.
Disclaimer of implied warranties & consequential damages
This warranty shall not be interpreted to render Degelman Industries Ltd. liable for injury, death, property damage or
damages of any kind, whether direct, consequential, or contingent to property. Without limiting the generality of the
foregoing, Degelman shall not be liable for damages resulting from any cause beyond its reasonable control, including,
without limitation, loss of crops, any expense or loss of labour, supplies, rental machinery or loss of use.
No other warranty of any kind whatsoever, express or implied is made with respect to this sale; and all implied warranties
of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are
hereby disclaimed and excluded from this sale. This exclusion shall not apply in any jurisdiction where it is not permitted
by law.
This limited warranty shall not apply:
1. If, in the sole opinion of Degelman, the unit has been subjected to misapplication, abuse, misuse, negligence,
accident or incorrect installation.
2. To any goods that have sustained damage or deterioration attributable to a lack of routine maintenance (eg. Retorque of mounting hardware.)
3. If parts not made or supplied by Degelman have been used in the connection with the unit, if, in the sole judgement
of Degelman such use affects its performance, safety, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Degelman dealership in a manner which, in the
sole judgement of Degelman, affects its performance, safety, stability or reliability.
5. To expendable or wear items such as cutting edges, skid shoes, and any other items that in the company’s sole
judgement is a wear item.
No employee or representative of Degelman Industries Ltd. is authorized to change this limited warranty in any way or
grant any other warranty unless such change is made in writing and signed by the Degelman Service Manager.
This limited warranty is subject to any future availability of supply, which may directly affect Degelman’s ability to obtain
materials or manufacture replacement parts.
Degelman reserves the right to make improvements in design or changes in specifications at any time, without incurring
obligations to owners of equipment previously delivered.
This limited warranty is subject to compliance by the customer to the enclosed Retail Customer’s Responsibility Under
Degelman Warranty.
Make certain the warranty registration card has been forwarded to: Degelman Industries Ltd.
Box 830
272 Industrial Dr.
Regina, SK, Canada
S4P 3B1
143351 - 69/7200 Series (12-May-2017)
-28-
Loading...