Defy 620, 621 User Manual

You can rely on Defy. To simplify

OWNER’S MANUAL

FOR MODELS:

620 Kitchenaire

Spiral plates

621 Kitchenaire

Solid plates

CONTENTS

2 Introduction
2 Unpacking
2 Installation
2 Electrical installation
2 Anti-tilt mechanism
3 Anti-tilt mechanism assembly
4 Safety advice
5 Control panel
5 6 Position selector knob
6 Using the oven
7 Solid plates
8 Spiral plates
8 Warming drawer
8 Maintenance
9 Cleaning the oven
9 Replacing the oven lamp
9 Removable oven door
10 Do and Don’t guide
11 Problem check
11 Owners responsibility
11 Service centres
12 Warranty

Kitchenaire

Stove

The Manufacturer

strives for continuous

improvements.

For this reason, the text

and illustrations in this

book are subject to

change without notice.

12 Purchase details

Part Number 068 364

PAGE 1 OF12

Please register your

product at

www.defy.co.za

Introduction

Congratulations on the purchase of this quality product.
We trust that you will enjoy many years of trouble free use. Please read these instructions
carefully before using the stove. This manual will provide you with information on how
to operate and care for your product in order that you gain the maximum benefit from it.

Unpacking

• Please ensure that packaging material is disposed of in a responsible manner.

• Plastic bags should be cut up to prevent children playing with them and accidentally

suffocating.

• Remove all packing from the oven cavity and position the accessories.

• If the appliance is damaged in any way, do not use it. Report the damage to your dealer,

who will take the necessary corrective action.

Installation

• Levelling feet are provided to assist you in positioning your stove, so that it will stand

firm and level. To adjust the level, turn the relevant foot to either raise or lower the
stove.

• Surfaces immediately adjacent to the oven should be able to withstand temperatures of

up to 100°C without delaminating or discolouring.

Electrical installation

This appliance must be earthed and the manufacturer and the seller do not accept
responsibility for any damage due to incorrect installation or electrical connection.

This appliance should not be connected through an earth leakage system.
Refer to S.A.N.S. 10142

Connection to the power supply

This appliance has a ‘Y’ type supply cord connection and must be installed by a licensed
electrician, who will ensure that the stove is correctly connected and safely earthed. The
rated current is printed on the serial number label attached to the stove upper back panel.
.
The appliance must be connected to the mains through an All pole isolating switch which
has a minimum clearance between the contacts of 3 mm. in All poles.
A means for disconnection must be provided in the fixed wiring.

Anti-tilt mechanism

WARNING

All stoves can tilt if you or a child sit or lean on an open oven door.
Safety regulations stipulate that the ANTI-TILT mechanism supplied with the stove,
must be fitted as shown on page 3.

PAGE 2 OF12

Anti-Tilt mechanism

• “A” 1 x Stability chain

• “B” 1 x Stability hook with anchor sleeve

• “A” is factory fitted at the rear of the stove in the centre. (See overleaf for instructions

if the removable splashback is to be fitted)

• Position the stove and move “A” to touch the wall behind the stove.

• Mark the hole where “A” touches the wall behind the stove.

• Move the stove away from the wall to allow for an area to work in.

• Using a 8.0 mm concrete bit, drill a hole at the marked position.

• Using the Stability hook and anchor sleeve “B”, firmly secure “B” to the wall.

• Slide the stove back in position and engage the stability chain “A” onto the Stability

hook “B”.

• The stove is then secured and will not accidentally tilt if downward pressure is applied

to the open oven door.

Safety regulations stipulate that the ANTI-TILT mechanism supplied with the stove,
must be fitted as shown.

PAGE 3 OF12

Safety advice

This section contains safety instructions that
will help you avoid risk of injury and
damage. All warranties will become void if
you do not follow these instructions.

General safety

• This appliance is not intended for use by

persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
the use of the appliance by a person
responsible for their safety.

• Children should be supervised to ensure

that they do not play with the appliance.

• Connect the appliance to an earthed outlet/

line protected by a fuse of suitable
capacity. Have the earth installation made
by a qualified electrician. Our company
shall not be liable for any problems arising
due to the appliance not being earthed in
accordance with the local regulations.

• If the supply cord is damaged, it must be

replaced by the manufacturer, its service
agent or similar qualified persons in order
to avoid a hazard.

• Do not operate the appliance if it is

defective or has any visible damage.

• Do not carry out any repairs or

modifications on the appliance.

• Never wash down the appliance with

water! There is the risk of electric shock!

• Never use the appliance when your

judgment or coordination is impaired by
the use of alcohol and/or drugs.

• The appliance must be disconnected from

the mains during installation, maintenance,
cleaning and repair procedures.

• Be careful when using alcoholic drinks in

your dishes. Alcohol evaporates at high
temperatures and may cause a fire since it
can ignite when it comes into contact with
hot surfaces.

• Do not heat closed tins and glass jars in the

oven. The pressure that would build up in
the tin/jar may cause it to burst.

• Do not place baking trays, dishes or

aluminium foil directly onto the bottom of
the oven. The heat accumulation might
damage the bottom of the oven.

• Keep all ventilation slots clear of

obstructions.

• The appliance may be hot when it is in

use. Never touch the hot burners, inner
sections of the oven, heaters etc.

• Always use heat resistant oven gloves

when putting in or removing dishes from
the hot oven.

• Do not use the appliance with the front

door glass removed or cracked.

• The rear surface of the oven gets hot when

it is in use. Make sure that the gas/
electrical connection does not come into
contact with the rear surface as
connections may get damaged.

• Do not trap the mains cable between the

oven door and frame and do not route it
over hot surfaces as the cable insulation
may melt and cause a fire as a result of a
short circuit.

• Make sure that the function knobs are

switched off after every use.

• When using Gas, ensure that the room is

well ventilated.

• Always keep children and infirm persons

away from the appliance when it is in use.

• Only use the appliance for preparing food.

• Use a deep pan, large enough to cover the

appropriate burner.

• Always dry food thoroughly before

placing it in hot oil or fat. Frozen food in
particular will spit and splatter if added too
quickly.

• Never fill the pan more than one third full

of fat or oil.

• Never heat fat or fry with a lid on the pan.

• Do not fry too much food at once. This

lowers the temperature of the oil or fat and
results in fatty foods.

• Do not leave hot fat or oil unattended. If

overheating occurs, these could catch fire.

• Do not store flammable items in the oven.

• Always keep the oven door gasket clean.

PAGE 4 OF12

The control panel

WARME R

DRA WER

621

Kitchenaire

6 PO SIT ION

SELEC TOR KN OB

OVE N
THERM OSTAT

L FR ON T

PLA TE

L REAR

PLA TE

R REAR

PLA TE

R FRONT

PLA TE

WARME R

DRA WER

6 PO SIT ION

SELEC TOR KN OB

OVE N
THERM OSTAT

L FR ON T

PLA TE

L REAR

PLA TE

R REAR

PLA TE

R FRONT

PLA TE

620

Kitchenaire

Note: Model 620 has energy regulators controlling the spiral plates and as a result, does not feature plate

indicator lights.

6 Position selector knob

OFF POSITION

Oven Light: To switch on the light, turn
the selector knob until the light icon,
depicted on the knob, is at the top. The
light remains on when any other functions

Switches on

the Oven Light

0

G

Selects the Grill

R

element only

I

L

L

are selected.

Top and Bottom elements (Conventional
Bake): Both the bottom bake element and

Selects both the Top

and Bottom elements

Selects the Top
element only

the top heat element are utilised. This
position is ideal for baking, roasting and

Selects the Bottom element only

cooking.

Bottom element only: Selecting only the bottom element and setting the thermostat at the lowest
temperature, allows the oven to be used as an additional warming space, should the warming

drawer be fully utilised.

Top element only: Selecting only the top element assists in gentle defrost.

Grill: Select the grill function for conventional grilling.

Note: All ovens extract moisture from the food being cooked, especially so during the winter months. This
is normal and not detrimental to the food or the oven.

PAGE 5 OF12

Using the oven

Baking

• This product is supplied with one chromed oven shelf and an extra large roast

pan. If required, additional shelves, roast pans and a broiler may be purchased
from any Defy Service Centre.

• Set the selector knob to the desired baking mode. See descriptions on page 5. Top and

Bottom elements or Bottom element only or Top element only.

• Set the oven thermostat to the required temperature.

• The thermostat indicator light will glow and remain on until the oven has reached the

selected temperature. The light will then switch off.

• Thereafter place the food in the oven.

• During the baking cycle, the indicator light will switch on and off as the thermostat

maintains the selected temperature.

• After baking is completed, the thermostat and the selector knob must be turned to

the "0"position in an anti clockwise direction.

• Note: The oven thermostat is marked down to 70°C. When set to this position, the

oven may be used as a warmer.

Baking Guide:

• Where possible, bake on the middle shelf position of the oven.

• Place the food halfway between the back of the oven and the door.

• Do not open the oven door until at least two thirds of the baking time has lapsed.

• The roast pan must not be used for baking purposes.

• For best baking results use an aluminium bake tray (380mm x 260mm x 30mm).

These are available from all Defy Parts Centres. Part number 067610.

• Teflon coated baking trays are not recommended.

Grilling

• The oven door must remain partially open (approx. 80 mm) during grilling.

• Both the wire shelf and roast pan/shelf may be used for grilling.

• The roast pan may also be used as a drip tray under the wire shelf.

• Position the shelf in the desired position below the grill element.

• Set the selector switch and oven thermostat to their respective Grill positions.

• The thermostat indicator light will glow.

• Pre-heat the grill element for about 5 minutes.

• Partially withdraw the shelf and place the food in the centre of the shelf.

• Slide the shelf back into position and partially close the door.

• Monitor the grilling to avoid burning the food.

• After grilling is completed, the oven thermostat and the selector switch must be re-

turned to the "0" position in an anti-clockwise direction.

WARNING

Accessible parts may become hot when grilling. Always use oven gloves when handling
food in the oven and keep children well away from the stove when it is in use

PAGE 6 OF12

Solid plates (621 Kitchenaire)

Red dot plates

• Plates featuring a red dot in the centre are high speed, high wattage plates for increased

performance

• For your safety these plates are fitted with thermal limiters. Should a plate be accidentally

switched on and left unattended, the limiter will reduce the power output of the plate and
minimise the risk of overheating and the possibility of fire.

Caring for Solid Plates

• Before using the plates for the first time, switch them on for about 4 minutes at the

highest setting. This allows the factory applied protective coating to burn in.

• To prevent blotchy discolouration and corrosion, moisture from spatters and spills should

be cleaned off immediately.

• To clean the plates, wipe them with a damp cloth or nylon pad. A little liquid detergent

may be used. Do not use metal scourers or sharp metal objects to clean the plates.

• After cleaning, dry the plates by switching them on for a short while.

• To prevent rust, periodically apply some, sewing machine oil or electrical hotplate

polish - available from Defy Service Centres. Extra attention is required in areas of
high humidity or in close proximity to the sea.

Recommendations

• Use only pots with a solid level base. An uneven base can prolong cooking times and

waste energy.

• Use pots with a base diameter slightly larger than the plate. This will ensure even heat

distribution and prevent spillage from dripping onto and staining the hot plate.

• Always cover the pot with a lid. This will conserve energy and minimise spillage.

• Thermal shock could damage the plates. Do not put cold pots on very hot plates.

Plate controls—variable

• Select the heat level by turning the knob to the required setting.

• You may select any setting.

• 1= low , 3 = medium and 6 = high.

• The relevant plate indicator light will glow, when the plate is switched on. (model 621

only).

WARNING

PAGE 7 OF12

The warranty does not cover the replacement or repair

of rusted or corroded plates.

Spiral plates (620 Kitchenaire )

Spiral plate control knobs.

• The plate will operate at any setting between minimum and maximum as depicted on the

control knob. With a little experience you will soon find the ideal position for:

• Gentle simmer to simmer.

• Fast simmer to medium heat

• Hot to maximum heat

Spiral plate care.

• Use pots with a base diameter slightly larger than the plate. This will ensure even heat

distribution and prevent spillage from dripping onto and staining the plate.

• Always cover the pot with a lid as this will conserve energy and minimise spillage.

Cleaning spiral plates.

• Switch off the electrical supply point to the stove.

• When the plates are cold, lift the hinged spiral plate up and remove the supports, under-

cups and trims.

• Use hot soapy water to clean the plates, plate supports, trims and under-cups.

• Use a nylon brush on badly soiled items.

• Wipe dry after cleaning and replace items.

Warming drawer

• The warming drawer has a rotary on off switch control.

• On models 620 and 621 only, an indicator light will glow when the drawer has been

switched on.

• Food left for too long in the warmer drawer could dry out and spoil. As a precaution food

should always be covered, to minimise the drying effect.

• The drawer can be removed for cleaning purposes.

• Pull the drawer out to the bump- stop, then lift the front slightly and continue pulling till

the drawer slides free.

• Refit by lifting the rear of the drawer over the bump-stop and then sliding it back.

Maintenance

General cleaning

• Switch off the electrical power supply before cleaning any part of the appliance.

• Wipe down glass panels, cabinet, door, control knobs, trims and handles with a hot soapy

cloth. Do not use a steam cleaner.

• Use only liquid household cleaners and avoid abrasive powders, scouring pads and

caustic cleaners.

• Rinse and wipe down with a clean cloth.

PAGE 8 OF12

Cleaning the oven

• Switch off the electrical power supply before cleaning any part of the appliance.

• Open the oven door and allow the oven to cool down.

• For improved access, the shelf, roast pan and oven door may be removed.

• Clean the oven with a damp, hot soapy cloth. Do not use a steam cleaner.

• It may be necessary to soak burnt soils with a liquid cleaner to soften them before

scrubbing them with a nylon brush or scouring sponge.

• Heavy soils on the bottom of the oven may require overnight soaking under a sponge

liberally sprinkled with household ammonia. The soil can then be removed the following
morning by washing normally.

• Do not use metal objects or steel wool to

ELEMENT GUARD

clean the oven.

• After cleaning, fit the bottom element into

ELEMENT

the hooks of the element guard. Failure to
observe this precaution would allow the

HOOK

element to rest on and possibly damage the
oven enamel.

Oven light

The oven light is switched on by the oven thermostat and switches off when the thermostat
knob is returned to 0.
To replace a faulty light bulb, proceed as follows.

• Switch off the power at the wall isolator to avoid the possibility of electric shock.

• Remove the light cover by unscrewing it in an anti-clockwise direction

• Unscrew the faulty bulb and fit a new 25 watt bulb rated for 300’C

• Refit the light cover.

Removable oven door

The oven door may be removed to improve access to the oven for cleaning purposes.
1 Open the door fully to expose the hinges (A) on either side.
2 Flip the hinge locking levers (B) to the upright position.
3 Partialy close the oven door and lift it free of the side panel retaining slots.
4 After cleaning, re-fit the oven door in reverse order making sure that the bottom hinge

notches © locate properly onto the bottom edges of the side panel retaining slots.

PAGE 9 OF12

B

A

SIDE OF DOOR

SIDE OF DOOR

1 2 3

C

R

O

O

D

F

O

E

D

I

S

OVER THE YEARS, DEFY'S SERVICE CENTRES

HAVE IDENTIFIED THIS LIST OF DO'S AND DON'TS

AS BEING IMPORTANT FOR CUSTOMER SATISFACTION AND

SAFETY. PLEASE READ IT AND

FAMILIARISE YOURSELF WITH ITS CONTENTS.

Do

• Clean your appliance regularly This

will prolong it's good looks and
enhance hygiene levels.

• Use flat bottomed pots and pans

when cooking on the hotplates. This
will maximise efficiency and reduce
electricity costs.

• Keep children well away from the

cooking appliance. Explain the
dangers to them. Being safety
conscious is being safe, not sorry.

• Supervise the cooking process.

Overcooked or spoiled food is
wasteful.

• Leave about a 40mm. air gap

between baking tins and the oven
walls. Adequate air circulation is
important for good baking results.

• Get into the habit of wearing oven

gloves when handling utensils in a
hot oven. This will help to avoid
accidental burns.

• Partly slide out the oven shelf before

removing hot dishes from the oven.
This will prevent accidental contact
with the hot oven sides.

Don’t

• Use pots which are smaller than the

hotplate diameter. This wastes
electricity and allows the pot
handles to overheat.

• Leave the appliance unattended

especially when grilling. This is
good practice and avoids accidents.

• Place anything on the open oven

door. The glass is not a work
surface and could get scratched.

• Use abrasive cleaning materials.

They will scratch surfaces and facia
graphics.

• Allow fat splashes to dry and bake

onto the stove/oven surface before
cleaning them. It is easier to clean
spills while they are still slightly
warm and soft.

• Put baking tins on the floor of the

oven. This will prevent heat
circulation and spoil baking results.

• Use the appliance to heat the home.

Neither the hotplates nor the oven
were designed for this purpose and
damage could occur.

• Allow pot handles to overhang the

front of the appliance. Children
might be tempted to grab them with
harmful consequences.

PAGE 10 OF12

Problem check

Do not attempt any repairs yourself.
Before calling a service technician to assist with a problem, please check:

• The mains distribution board for tripped circuit breakers.

• The wall switch is on.

Remember that you may be charged for a service call even during the warranty
period if the fault is due to or caused by any of the above.

Owner’s responsibility

Since the following are not factory faults, they are the owner’s responsibility.

• Damage to exterior finish.

• Breakage of glass and other components.

• Replacement of the light bulb.

• Damage through improper installation or use of the appliance.

• Damage caused by moving the appliance.

WARNING: Under no circumstances should the bake element be
covered with aluminium foil. Nor should a pan or tray be positioned
directly above the bake element.

Doing so would reflect the heat from the bake element downwards. Heat
to the oven would be restricted and overheating of the space below the
element would result in damage to the oven enamel.

Service Centres

IF YOU HAVE FOLLOWED THE INSTRUCTIONS AND STILL HAVE A PROBLEM, CONTACT THE NEAREST
DEFY SERVICE CENTRE. THEY WILL BE ABLE TO ADVISE YOU ON ANY ASPECT OF THE PRODUCT OR
SEND A QUALIFIED TECHNICIAN TO REPAIR IT.

BLOEMFONTEIN

160 Long Street, Hilton,
Bloemfontein 9301.
Tel. [phone]
[e-mail]

CAPE TOWN

5A Marconi Rd.
Montague Gardens, 7441.
Tel. [phone]
[e-mail]

DURBAN

35 Intersite Avenue,
Umgeni Business Park, Durban

4051.
Tel. [phone]
[e-mail]

EAST LONDON

16 Bowls Rd. Arcadia,
East London 5201.
Tel. [phone]
[e-mail]

POLOKWANE

87 Nelson Mandela Drive.
Superbia 0699.
Tel. [phone] / 7 / 8 / 9.
[e-mail]

PORT ELIZABETH

112 Patterson Road,
North End, Port Elizabeth 6001.
Tel. [phone]
[e-mail]

JOHANNESBURG

Commercial Head Office,
Administration, Distribution,
National Groups, Tel. Sales,
Contracts and Credit.
Cnr. Mimetes & Kruger Sts.
Denver ext.12
Johannesburg. 2094.
Tel. [phone] or 011 621
0300
[e-mail]

PRETORIA.
Block A1 Old Mutual Industrial
Park.
Cnr. D.F.Malan Drive & Moot Str.
Hermanstad. 0082.
Tel. [phone]
[e-mail]

OTHER AREAS ARE SERVICED BY OVER 200 AUTHORISED SERVICE AGENTS.

PLEASE CONSULT THE NEAREST REGIONAL DEFY SERVICE CENTRE FOR DETAILS

PAGE 11 OF12

WARRANTY

This certificate is issued by DEFY APPLIANCES LIMITED manufacturers of Defy and Ocean
products, hereinafter the Company, to the original purchaser only, of the appliance described on the
certificate and shall constitute the only warranty given in respect of this appliance.
The Company warrants to the original purchaser that for a period of TWO YEARS from date of
purchase the appliance is free from defect under normal domestic use, both in workmanship and
material, subject to the following conditions.

1. Repair or replacement of any part of this appliance, found by the Company to be defective, shall
be at the election of the Company. The Company reserves the right to effect such service through
any of its Service Divisions or Authorised Service Dealers. The cost of such service shall be borne
by the Company in full, provided that the appliance is located no further than 50 km from a
Company Service Centre or an Authorised Service Dealer. Where the appliance is located
beyond the 50 km radius, the purchaser shall be liable for the standard travelling charges, as
determined by the Company.

CARRY IN SERVICE Microwave ovens, Compact cookers and small appliances are repaired in

our service centres and are not collected from the customers home. Faulty units should be
delivered to the purchasing dealer or to the nearest Company Service Centre for warranty repairs.

2. Rusted or corroded solid plates, vitreous enamelware, fuses and lamps are specifically excluded
from these warranties. It is an express condition of these warranties that the purchaser takes due
care and attention in the use and maintenance of the appliance. Abuse, misuse in conflict with
operating instructions, connection to incorrect voltages and subjection to commercial use shall
release the Company from its obligations.

3. This warranty shall become void and cease to operate if the appliance is dismantled by, or any
repairs to the appliance are effected by any persons not duly authorised by the Company, or if
substitute parts not approved by the Company are used in the appliance, or if the serial number of
the appliance is removed.

4. The Company shall not be responsible for damages resulting from fire, flood, civil disturbances or
any Act of God. The Company shall not, in terms of these warranties be responsible nor held liable
for any consequential loss or damage of any kind caused by or due to the failure or malfunction of
the appliance.

5. The Company shall not be responsible for transportation or other costs other than those incurred
within the provisions of Point 1 of this Certificate.

6. These warranties shall not apply to the appliance if it is purchased or used beyond the borders of
the Republic of South Africa, Namibia, Botswana, Swaziland and Lesotho.

7. Where service is requested under warranty and no fault or defect can be found by the Company,
all costs incurred will be for the purchaser's account.

8. This Certificate as well as your invoice will serve as proof of purchase. For the purpose of
warranty, it will be essential to produce this Certificate and invoice. Failure to do so, will render the
purchaser liable for service costs.

KEEP THIS CERTIFICATE AND SALES INVOICE AS PROOF OF PURCHASE

FOR WARRANTY PURPOSES.

For future reference, record the listed information in the space below. The Serial number may be found on
the label located at the upper back panel.

SERIAL No.

DATE OF PURCHASE.

PURCHASED FROM

PAGE 12 OF12

Part Number 068 364