THANK YOU
for purchasing the Definitive Technology ProCinema 6D System. This high-performance six-speaker
system is designed to deliver equally superb sound for home theater and music. Please read the
instructions carefully to familiarize yourself with the speaker system.
PROCINEMA 6D SYSTEM Overall Frequency Response: 22 Hz – 30 kHz Recommended Amplification: 10 – 175 watts/channel
PROCENTER 6D CENTER CHANNEL
Dimensions: 10.5” W x 4.25” D x 4” H
Frequency Response: 55 Hz – 30 kHz
Efficiency: 89 dB
Nominal Impedance: Compatible with 4 – 8 ohm outputs
Driver Complement: Two 3.25” BDSS bass/midrange drivers
coupled to two 3.25” pressure-driven
planar low-frequency radiators, 1”
Pure Aluminum Dome Tweeter
Recommended
Amplification: 10 – 175 watts
PROSUB 6D SUBWOOFER
Dimensions: 10.38” W x 13” D x 13” H
Frequency Response: 22 Hz – 150 Hz
Driver Complement: One 8” woofer with polymer cone,
one 8” infrasonic radiator
Built-in Amplifier: 250 watts RMS
High Pass Filter: 6dB/octave speaker level at 100 Hz
Low Pass Filer: 24dB/octave continuously variable
(40 Hz – 150 Hz)
Power Consumption: 60Hz 100-120V, 2.1A
PROMONITOR 6D SATELLITE SPEAKERS
Dimensions: 4” W x 4.25” D x 7” H
Frequency Response: 65 Hz – 30 kHz
Efficiency: 88 dB
Nominal Impedance: Compatible with 4 – 8 ohm outputs
Driver Complement: One 3.25” BDSS bass/midrange driver
coupled to one 3.25” pressure-driven
planar low frequency radiator, 1” Pure
Aluminum Dome Tweeter
Recommended
Amplification: 10 – 150 watts
REGISTER YOUR NEW DEFINITIVE TECHNOLOGY PRODUCTS AT
definitivetechnology.com/register
PLEASE INSPECT FOR SHIPPING DAMAGE
Each loudspeaker leaves our plant in perfect condition. Any visible or concealed damage
most likely occurred in handling after it left our plant and should be reported at once to
your Definitive dealer or the shipping company which delivered your loudspeaker.
PROCINEMA 6D SYSTEM OWNER’S MANUAL
SAFETY PRECAUTIONS (Read these safety instructions before operating the unit.)
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding t ype
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protec t the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufac turer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
FCC INFORMATION (FOR U.S. CUSTOMERS)
1. COMPLIANCE INFORMATION
This product complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this product may not cause harmful interference, and (2)
this product must accept any interference received, including inter ference that may
cause undesired operation.
Sound United, LLC
1 Viper Way, Vista, CA 92081
United States
Phone: +1 760-536-5300
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual,
meets FCC requirements. Modification not expressly approved by Sound United may
void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital
This product generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this product does cause harmful interference to
radio or television reception, which can be determined by turning the product OFF
and ON, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the local retailer authorized to distribute this type of product or an
experienced radio / TV technician for help.
4. IMPORTANT (FOR NETWORK MODEL)
When connecting this product to network hub or router, use only a shielded STP
or ScTP LAN cable which is available at retailer. Follow all installation instructions.
Failure to follow instructions could void your authority, granted by the FCC, to use
the product.
5. CAUTION (FOR BLUETOOTH/WI-FI MODEL)
• To comply with FCC RF exposure compliance requirement, separation distance of at
least 20 cm must be maintained between this product and all persons.
• This product and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
IC INFORMATION (FOR CANADIAN CUSTOMERS)
CAN ICES-3 (B) / NMB-3 (B)
CAUTION:
To completely disconnect this product from the mains, disconnect the plug from the
wall socket outlet. The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
CAUTIONS ON INSTALLATION:
For proper heat dispersal, do not install this unit in a confined space, such as a
bookcase or similar enclosure.
Amplifier: 0.3 m or more
Other units: 0.1 m or more
CAUTION (FOR AMPLIFIER):
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal heat sink may become hot when
operating this product continuously. Do not touch hot areas,
especially around the “Hot surface mark” and the top panel.
NOTES ON USE
WARNINGS
• Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack.
• Handle the power cord carefully. Hold the plug when unplugging the cord.
• Keep the unit free from moisture, water, and dust.
• Unplug the power cord when not using the unit for long periods of time.
• Do not obstruct the ventilation holes.
• Do not let foreign objects into the unit.
• Do not let insecticides, benzene, and thinner come in contact with the unit.
• Never disassemble or modify the unit in any way.
• Ventilation should not be impeded by covering the ventilation openings with items,
such as newspapers, tablecloths or curtains.
• Naked flame sources such as lighted candles should not be placed on the unit.
• Observe and follow local regulations regarding battery disposal.
• Do not expose the unit to dripping or splashing fluids.
• Do not place objects filled with liquids, such as vases, on the unit.
• Do not handle the mains cord with wet hands.
• When the switch is in the OFF (STANDBY) position, the equipment is not completely
switched off from MAINS.
• The equipment shall be installed near the power supply so that the power supply is
easily accessible.
• Do not keep the battery in a place exposed to direct sunlight or in places with
extremely high temperatures, such as near a heater.
• Do not bend forcedly the plug on the equipment for the connection between the
connector and micro USB/USB cable.
HOT SURFACE MARK
PROCINEMA 6D SYSTEM OWNER’S MANUAL
WHEN MOUNTING
THE SPEAKERS ON A WALL
• The speakers can be mounted on a wall using the
keyhole hook on its rear panel.
• When you mount the speakers, be sure to install
them properly and securely.
1. Screw in one self-tapping screw (commercially available
5/32 inch / 4mm to 3/16 inch / 5mm diameter) into a
wall that has sufficient strength to support the weight
of the speaker,or into reinforcing material on the wall.
2. Hook the keyhole hook on the back of the speaker
onto the head of the self-tapping screw.
• Check that the head of the self-tapping screw hooks securely
into the keyhole hook hole.
• Do not attempt to install this product onto a wall made of material
that may crumble easily, such as mortar or decorative plywood.
Doing so may result in the screw pulling out and speaker falling,
causing damage to the speaker or injury.
• Do not install the speaker using other methods such as nails or
double-sided tape. The nails may become loose due to vibration or
the double-sided tape may peel off due to prolonged use, causing
the speaker to fall.
• Be sure to fix the cables in place so that they cannot be pulled or
tripped over by accident.
• Be sure to check that the product is safe after installation. Please
note that we cannot accept any liability for accidents, etc. that occur
as a result of where or how this product is installed. If you are
unsure of how to install this product safely, request a professional
contractor do the installation work.
PROCINEMA 6D SIX-PIECE
SURROUND SOUND SYSTEM
This system is designed to be used as a 5.1 Dolby/DTS surround
sound home theater.
CONNECTING YOUR LOUDSPEAKERS
FIGURE 3 – WIRING AND POLARITY
+
-
Strip 0.25” (6mm) wire.
1
2
1. Unscrew binding post and insert wire.
2. Tighten until wire is secure.
METHOD 1
1. First, wire the + (red) terminal of the left channel speaker wire
output of your receiver or amplifier to the + (red) terminal of the
left channel speaker wire (high-level) input of your ProSub 6D.
2. Next, wire the – (black) terminal of the left channel speaker wire
output of your receiver or amplifier to the – (black) terminal of
the left channel speaker wire (high-level) input of the ProSub 6D.
3. Repeat Steps 1 and 2 for the right channel.
4. Wire the + (red) terminal of the left ProMonitor 6D to the left
Identify markings on wire and assign +/-.
Satellite Speakers
Receiver/Amplifier
Ensure that the speaker is always connected
to the receiver or amplifier+ to + and – to –.
channel +(red) speaker wire (high-level) out on the back of
the ProSub 6D.
5. Wire the – (black) terminal of the left ProMonitor 6D to the left
channel – (black) speaker wire (high-level) out on the back of
the ProSub 6D.
6. Repeat steps 4 and 5 for the right ProMonitor 6D.
7. Set the low frequency filter control on the back of the
subwoofer to approximately 10 – 12 o’clock. Please note that
the exact frequency will depend on many factors including
specific positions of the speakers in the room, so you might
experiment with a slightly higher or lower setting to achieve
ideal blending between the sub and the satellites for your
particular setup. Listen to a wide variety of music to determine
the correct setting for this in your system.
8. Set the subwoofer level control to approximately 12 o’clock.
Please note that the exact level depends on many factors
including your room size, positions of the speakers, etc. as well
as your personal listening taste, so you might experiment with
the subwoofer level while listening to a wide variety of music
until you achieve the ideal setting for your system.
9. Wire your center channel to the center channel out on your
receiver (or center channel amplifier) and your left and right rear
surround speakers to the rear channel outputs on your receiver
or rear channel amplifier (taking care that all speakers are in
phase, i.e. + (red) to + (red) and – (black) to – (black)).
10. Set the bass management system of your receiver or decoder
for “Large Left and Right Main Speakers,” “Small Center,”
and “Small Rear Surround Speakers” and “No Subwoofer.”
All the bass information including the .1 channel LFE signal
will be directed to the main left and right channels and into
the subwoofer giving you all the benefits of Dolby Digital.
OPTION FOR METHOD 1 HOOK-UP
In addition to the hook-up as described above, you may use an
RCA-to-RCA low level cable to connect the LFE/sub-out on your
receiver to the low-level LFE/sub-in on a ProSub 6D. Set your
Speaker Setup to “Large Left and Right Main Speakers” and a
“Subwoofer” and “Small Center” and “Small Surrounds.”
METHOD 2
1. Wire the left front ProMonitor 6D directly to the left front
channel of your amplifier or receiver and the right front
ProMonitor 6D directly to the right channel of your amplifier or
receiver taking care that the speakers are in phase, i.e. + (red)
to + (red) and – (black) to – (black).
2. Use an RCA-to-RCA low-level cable to connect the LFE
subwoofer out on your receiver to the LFE input on your subwoofer.
3. Wire your center channel to the center channel out on your
receiver (or center channel amplifier) and your left and right rear
surround speakers to the rear channel outputs on your receiver
or rear channel amplifier (taking care that all speakers are in
phase, i.e. + (red) to + (red) and – (black) to – (black)).
4. Set the Speaker Setup of your receiver or decoder for “Small
Left and Right Main Speakers,” “Small Center” and “Small
Rear Surround Speakers” and “Yes Subwoofer.”
5. Set the variable low-pass crossover to 150 and set the
subwoofer level control to 12 o’clock. Please note that you
can set the subwoofer level either by turning the subwoofer
level control on the back of the subwoofer or with LFE level
adjustment in your receiver. We suggest setting the subwoofer
to 12 o’clock and then making fine adjustments to the
subwoofer level using the LFE level control on your receiver.
POSITIONING YOUR
SPEAKERS IN YOUR ROOM
It is important that some simple setup recommendations be
followed in order to assure optimum performance in your room.
Please remember that although these recommendations are
usually valid, all rooms and listening setups are somewhat unique,
so do not be afraid to experiment with the speakers. Remember,
whatever sounds best to you is correct.
POSITIONING THE PROMONITOR 6D SATELLITE
SPEAKERS IN YOUR ROOM
When used as front or side/rear surround speakers, the ProMonitor
6Ds may be placed on a stand, a shelf, or mounted on the wall or
ceiling. If you place the speakers on a shelf, try to position them
forward on the shelf with the front of the speaker even with the
front of the shelf. If you wish to use a stand, we recommend the
Definitive ProStand 60/80/600/800. Definitive stands have been
designed for optimal performance and style. The ProMonitor 6Ds
may be wall mounted by using the keyhole built into the speaker or
by using a ProMount 80/800 pivoting mount available separately.
POSITIONING YOUR PROMONITOR 6D FRONT SPEAKERS
Your two ProMonitor 6D front speakers (please note all ProMonitor
6Ds are exactly the same) should be placed 6 to 8 feet apart and
kept away from side walls and corners if possible. A good rule is
to place the speakers separated by one half the length of the wall
they are positioned along.
Speakers may be angled in toward the listening position or
pointed straight ahead. Note: Angling the speakers in so that
they point directly at the listeners will result in more detail and
greater clarity.
POSITIONING YOUR PROMONITOR 6D REAR/SIDE
SURROUND SPEAKERS
The surround speakers may be located on the side or behind the
listeners. When used on the sides, take care never to locate the
speakers forward of the listeners. The speakers may be located
at or above ear level. If the speakers are placed on the rear wall,
follow the same guidelines given for positioning the front speakers
along the wall.
POSITIONING YOUR PROCENTER 6D CENTER
CHANNEL SPEAKER
The ProCenter 6D can be placed either above or below the TV. If
you are putting the ProCenter 6D on a shelf or on a TV, try to place
it forward with the front of the speaker even with the front of the
TV or the front of the shelf.
PROCENTER 6D VERTICAL ANGLE ADJUSTMENT
Your ProCenter 6D loudspeaker has a simple built-in device which
allows you to adjust the vertical angle of the speaker. Please note
that on the rear/center/underside of the speaker there is a foot.
When you set the speaker down, the speaker will lean back and
rest on the foot. By varying how far you screw in the foot, you
can adjust the vertical angle of the speaker. We suggest that you
position the speaker so that it aims directly toward the height of
the listener’s ear.
SUBWOOFER PLACEMENT
Your Definitive Technology subwoofer has been designed to
operate at frequencies generally below 150 Hz. Because low-
frequency information in this range essentially is non-directional,
your subwoofer can be located anywhere in your listening room
that is most convenient. Also, the continuously variable low-pass
filter operates at a very fast roll-off, ensuring great performance
wherever you place your subwoofer. There are, however, some
general rules that you should bear in mind when locating your
subwoofer:
1. For maximum output, the subwoofer should be placed in
a corner or against the wall, leaving roughly 2”– 4” clearance
between the subwoofer and the wall(s).
2. Corner placement will increase the subwoofer’s efficiency, which
in turn will increase your system’s maximum output and improve
the dynamic capability of the subwoofer.
3. While one Definitive Technology subwoofer will always
sound great, the use of two subwoofers will definitely enhance
your system’s performance by providing a smoother and more
consistent response pattern. Here, it is recommended that you
locate the subwoofers on the same side of the room as the
main speaker of the same channel.
4. Always remember that frequency response and output level
are greatly influenced by the subwoofer’s placement. A
movement of even a foot or two can dramatically change your
system’s response characteristics. You should experiment with
placement in your particular listening room in order to achieve
the highest performance from your subwoofer.
5. Your subwoofer contains a powerful amplifier inside its
cabinetry. When placing the subwoofer into a built-in cabinet,
please be sure it receives a clear flow of cooling air. If your
subwoofer is to be located in a closed-back cabinet, be sure
to put some ventilation holes in the cabinet back behind the
subwoofer’s back panel.
POWERING UP YOUR SUBWOOFER
Your subwoofer contains a built-in, active powered subwoofer
section as well as an electronic crossover and so each subwoofer
must be plugged into an electrical socket of the appropriate
voltage (as indicated on the back of your unit). The subwoofer has
a special circuit which automatically turns the powered subwoofer
section on when a signal is fed to the loudspeaker and does
not require an on-off switch. The red LED on the back panel will
light up when a signal is sensed and the amplifier turns on. It will
automatically turn off a little while after the signal is discontinued.
Please note that after the cessation of a signal, it may take up to an
hour for the amplifier to actually turn off from active to standby mode.
SUBWOOFER OPERATING CONTROLS
Your Definitive Technology ProSub 6D subwoofer is equipped
with a full complement of operating controls to ensure complete
flexibility and maximum performance in any installation. Most of
them basically are the “set and forget” type, although occasionally
certain controls will require minor adjustments.
LEVEL CONTROL
This control varies how loud the subwoofer plays. Please
follow the level control suggestions in the hook-up section.
LOW-PASS FILTER
Your subwoofer’s back panel features a continuously variable
low-pass filter. If you are using the low-level LFE input, you will
normally turn the Low-Pass Filter Control all the way up to 150. If
you are using Method 1 System Hook-up, you will normally set the